Elsner 70122 Guida

KNX W

Wind Sensor

Installation and Adjustment

KNX W 20...30 V DC

KNX W 230 V AC

No. 70122

No. 70123

1 Content

Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany

Wind Sensor KNX W • from software version 1.00, ETS programme version 1.1

Status: 11.11.2021 • Errors excepted. Subject to technical changes.

1. Description ........................................................................................... 3

1.1. Deliverables .............................................................................................................. 3

1.2. Technical specifications ........................................................................................... 3

2. Installation and commissioning ........................................................... 4

2.1. Location ..................................................................................................................... 5

2.2. Mounting the sensor ................................................................................................ 6

2.2.1. Attaching the mount ..................................................................................... 6

2.2.2. View of rear side and drill hole plan ........................................................... 7

2.2.3. Preparing the sensor .................................................................................... 8

2.2.4. PCB layout ..................................................................................................... 9

2.2.5. Mounting the weather station ................................................................... 10

2.3. Notes on mounting and commissioning .............................................................. 11

3. Addressing of the device at the bus .................................................. 12

4. Maintenance ....................................................................................... 12

5. Disposal ............................................................................................. 12

6. Transmission protocol ....................................................................... 14

6.1. List of all communication objects ......................................................................... 14

7. Setting of parameters ........................................................................ 17

7.1. General settings ..................................................................................................... 17

7.2. Threshold values .................................................................................................... 17

7.2.1. Wind threshold value 1 / 2 / 3 .................................................................... 17

7.3. Logic ....................................................................................................................... 19

7.4. AND Logic 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 ......................................................................... 19

7.4.1. Linkage inputs of AND Logic ..................................................................... 20

7.4.2. OR Logic 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 ................................................................ 21

7.4.3. Linkage inputs of OR Logic ........................................................................ 21

2 Clarification of signs

This manual is amended periodically and will be brought into line with new software

releases. The change status (software version and date) can be found in the contents footer.

If you have a device with a later software version, please check

www.elsner-elektronik.de in the menu area "Service" to find out whether a more up-to-

date version of the manual is available.

Clarification of signs used in this manual

Safety advice.

Safety advice for working on electrical connections, components,

etc.

DANGER! ... indicates an immediately hazardous situation which will lead to

death or severe injuries if it is not avoided.

WARNING! ... indicates a potentially hazardous situation which may lead to

death or severe injuries if it is not avoided.

CAUTION! ... indicates a potentially hazardous situation which may lead to

trivial or minor injuries if it is not avoided.

ATTENTION! ... indicates a situation which may lead to damage to property if it is

not avoided.

ETS In the ETS tables, the parameter default settings are marked by

underlining.

3 Description

Wind Sensor KNX W • Status: 11.11.2021 • Technical changes reserved. Errors reserved.

1. Description

The Wind Sensor KNX W measures wind speed and transfers the values to the KNX

system. Three switching outputs with adjustable threshold values as well as additional

AND and OR logic gates are available.The sensor system, the evaluation electronics

and the electronics of the bus connection are mounted in a compact housing.

Functions:

•Wind measurement: The wind strength measurement takes place

electronically and thus noiselessly and reliably, even during hail, snow and

sub-zero temperatures. Even turbulent air and anabatic winds in the vicinity of

the weather station are recorded

•Wind sensor monitoring: If the wind measurement value changes by less

than ± 0.5 m/s within 48 hours, the maximum measurement value of 35 m/s is

output as a fault message. All wind alarms with a limit value below 35 m/s

become active as a result

•3 threshold values can be adjusted per parameter or via communication

objects

•8 AND and 8 OR logic gates with each 4 inputs. Every switching incident as

well as 8 logic inputs (in the form of communication objects) may be used as

inputs for the logic gates. The output of each gate may optionally be configured

as 1 bit or 2 x 8 bits

Configuration is made using the KNX software ETS. The product file can be down-

loaded from the Elsner Elektronik website on www.elsner-elektronik.de in the “Ser-

vice” menu.

1.1. Deliverables

• Sensor with combined wall/pole mounting

• 2x stainless steel installation band for pole installation

1.2. Technical specifications

Housing Plastic material

Colour White / translucent

Mounting On-wall

Degree of protection IP 44

Dimensions approx. 96 × 77 × 118 (W × H × D, mm)

Weight 230 V AC version: approx. 240 g,

20...30 V DC version approx. 170 g

Ambient temperature Operation -30…+50°C, storage -30…+70°C

Operating voltage Available for 230 V AC or 20...30 V DC.

An appropriate power supply unit can be obtained from

Elsner Elektronik.

Cable cross-section Massive conductors of up to 1.5 mm² or conductors

with fine wires

4 Installation and commissioning

Wind Sensor KNX W • Status: 11.11.2021 • Technical changes reserved. Errors reserved.

The product conforms with the provisions of EU directives

2. Installation and commissioning

Installation, testing, operational start-up and troubleshooting should

only be performed by an authorised electrician.

DANGER!

Risk to life from live voltage (mains voltage)!

There are unprotected live components inside the device.

• Inspect the device for damage before installation. Only put undamaged devic-

es into operation.

• Comply with the locally applicable directives, regulations and provisions for

electrical installation.

• Immediately take the device or system out of service and secure it against un-

intentional switch-on if risk-free operation is no longer guaranteed.

Current 230 V AC version max. 20 mA.

20...30 V DC version: max. 30 mA., max. 0,4 W.

Residual ripple 10%

Data output KNX +/- bus terminal plug

Group addresses max. 254

Allocations max. 255

Communication objects 80

Measurement range Wind 0...35 m/s

Resolution (wind) 0,1 m/s

Accuracy (wind) at ambient temperature -20…+50°C:

±22% of the measurement value when incident flow is

from 45…315°

±15% of the measurement value when incident flow is

from 90…270°

(Frontal incident flow corresponds to 180°)

5 Installation and commissioning

Wind Sensor KNX W • Status: 11.11.2021 • Technical changes reserved. Errors reserved.

Use the device exclusively for building automation and observe the operating instruc-

tions. Improper use, modifications to the device or failure to observe the operating in-

structions will invalidate any warranty or guarantee claims.

Operate the device only as a fixed-site installation, i.e. only in assembled condition and

after conclusion of all installation and operational start-up tasks, and only in the sur-

roundings designated for it.

Elsner Elektronik is not liable for any changes in norms and standards which may occur

after publication of these operating instructions.

2.1. Location

Select an assembly location at the building where wind speed may be collected by the

sensor unobstructedly.

At least 60 cm of clearance must be left all round the device.This facilitates correct wind

speed measurement without eddies. The distance concurrently prevents spray (rain-

drops hitting the device) or snow (snow penetration) from impairing the measurement.

It also does not allow birds to bite it.

Fig. 1

There must be at least 60 cm of space below,

to the sides and in front of the sensor left

from other elements (structures, construction

parts, etc.).

60 cm

Fig. 2

The wind sensor must be mounted on a verti-

cal wall (or a pole).

Wall

pole

6 Installation and commissioning

Wind Sensor KNX W • Status: 11.11.2021 • Technical changes reserved. Errors reserved.

2.2. Mounting the sensor

2.2.1. Attaching the mount

The sensor comes with a combination wall/pole mount. The mount comes adhered by

adhesive strips to the rear side of the housing. Fasten the mount vertically onto the wall

or pole.

Fig. 3

The wind sensor must be mounted in the

horizontal transverse direction (horizontally).

Horizontal

Fig. 4

When wall mounting: flat side on wall, crescent-

shaped collar upward.

Collar

Fig. 5

When pole mounting: curved side on pole, collar

downward.

Collar

7 Installation and commissioning

Wind Sensor KNX W • Status: 11.11.2021 • Technical changes reserved. Errors reserved.

2.2.2. View of rear side and drill hole plan

Fig. 6

Different mounting arms are available from Els-

ner Elektronik as additional, optional accessories

for flexible installation of the weather station on

a wall, pole or beam.

Example of the use of a mounting arm:

Due to flexible ball joints, the sensor can be

brought into ideal position.

Fig. 7

Example use of the hinge arm mounting:

Fitting to a pole with worm drive hose clips

Slot hole 7,5 x 5 mm

Fig. 8 a+b

Drill hole plan

Dimensions of rear side of

housing with bracket. Sub-

ject to change for technical

enhancement.

8 Installation and commissioning

Wind Sensor KNX W • Status: 11.11.2021 • Technical changes reserved. Errors reserved.

2.2.3. Preparing the sensor

The sensor cover snaps in on the left and right along the bottom edge (see Fig.). The

cover of the 230V model is also screwed on top. Remove the cover. Proceed carefully,

so as not to pull off the wire connecting the PCB in the bottom part with the cover (sol-

dered cable connection in case of 230 V AC version, cable with plug in case of 20...30

V DC version).

Fig. 9

1 Screw-on cover (230V device)

2 Cover Snaps

3 Bottom part of housing

Unsnap cover and

remove upwards

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Elsner Sensore di sicurezza

Elsner

Elsner Sewi KNX L-Pr Guida

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente