ELTEX NTU-RG-5402G-W Manuale utente
FW 2.3.0 NTU-RG-54xx. User manual (user)
Optical network terminals
NTU-RG-5402G-W
NTU-RG-5421G-Wac
NTU-RG-5421GC-Wac
NTU-RG-5421G-WZ
NTU-RG-5440G-WZNTU-RG-5440G-Wac
Firmware version 2.1.0 (07.2020)
IP address: http://192.168.1.1
Login: user
Password: user
Introduction
A GPON is a network of passive optical networks (PON) type. It is one of the most effective state-of-the-art solutions of the last mile issue that enables
cable economy and provides information transfer downlink rate up to 2.5 Gbps and uplink rate up to 1.25 Gbps. Being used in access networks, GPON-
based solutions allow end users to have access to new services based on IP protocol in addition to more common ones.
The key GPON advantage is the use of one optical line terminal (OLT) for multiple optical network terminals (ONT). OLT converts Gigabit Ethernet and
GPON interfaces and is used to connect a PON network with data communication networks of a higher level. ONT device is designed to connect user
terminal equipment to broadband access services. It can be used in residential areas and office buildings.
The range of ONT NTU equipment produced by ELTEX comprises of terminals with four UNI interfaces of 10/100/1000Base-T and supports for FXS , Wi-
1
Fi, USB, Z-Wave , RF :
23
NTU-RG-5402G-W, NTU-RG-5421G-Wac, NTU-RG-5421GC-Wac, NTU-RG-5421G-WZ, NTU-RG-5440G-WZ, NTU-RG-5440G-Wac
This user manual describes intended use, main specifications, configuration, monitoring, and firmware update for NTU-RG optical terminals
.
Notes and warnings
Except NTU-RG-5440G-WZ, NTU-RG-5440G-Wac
1
For NTU-RG-5421G-WZ, NTU-RG-5440G-WZ
2
3 Only for NTU-RG-5421GC-WAC
Product Description
Purpose
NTU-RG GPON ONT
(Gigabit Ethernet Passive Optical Network) devices represent high-performance user terminals designed to establish a connection
with upstream passive optical network equipment and to provide broadband access services to the end user. GPON connection is established through the
PON interface, while Ethernet interfaces are used for connection of terminal equipment.
The key GPON advantage is the optimal use of bandwidth. This technology is considered as the next step in provisioning of new high-speed Internet
applications at home and office. Being developed for network deployment inside houses or buildings, these ONT devices provide robust connection with
high throughput and at long distances for users living and working at remote apartment and office buildings.
An integrated router allows local network equipment to be connected to a broadband access network. The terminals protect PCs from DoS and virus
attacks with the help of firewall and filter packets to control access based on ports and MAC/IP addresses of source and target. Users can configure a
home or office web site by adding a LAN port into DMZ. Parental Control enables filtration of undesired web sites, blocks domains and allows for
compilation of a schedule of Internet use. Virtual private network (VPN) provides mobile users and branch offices with a protected communication channel
for connection to a corporate network.
FXS port enable IP telephony and provide various useful features such as display of caller ID, three-way conference call, phone book, and speed dialling.
This makes dialling and call pick-up user friendly.
Notes contain important information, tips, or recommendations on device operation and setup.
Warnings inform users about hazardous conditions which may cause injuries or device damage and may lead to the device malfunctioning or
data loss.
USB ports can be used for USB-enabled devices (USB flash drives, external HDD).
Network router NTU-RG-5402G-W provides the connection via b/g/n Wi-Fi standard and ensures 2,4 GHz operation of the device. NTU-RG-5421G-Wac,
NTU-RG-5421G-WZ, NTU-RG-5421GC-Wac, NTU-RG-5440G-WZ, NTU-RG-5440G-Wac network routers allow Wi-Fi clients to be connected using IEEE
802.11a/b/g/n/ac standard. 802.11ac standard support ensures data transfer rate of 1733 Mbps and allows wireless network to be used for delivery of
modern high-speed services to client equipment. Two integrated Wi-Fi network controllers enable simultaneous 2.4 GHz and 5 GHz dual-band operation.
NTU-RG-5421G-WZ, NTU-RG-5440G-WZ come with «Smart Home» controller.
«Smart Home» controller allows organizing an energy-efficient wireless channel specifically for remote control. Unlike Wi-Fi and other IEEE 802.11 data
transmission standards, designed mainly for large streams of information, the «Smart Home» technology operates in the frequency range up to 1 GHz and
is optimized for transmitting simple control commands with low delays (for example, turn on/off , change the volume, brightness, etc.). Selection of low
radio-frequency range results from the small quantity of potential interfering sources (unlike the loaded 2,4 GHz band within which it is necessary to resort
to measures that reduce potential interference from various wireless home appliances – Wi-Fi, ZigBee, Bluetooth).
«Smart Home» controller is intended to create low-cost and energy-efficient consumer electronics, including battery-powered devices such as remote
controls, smoke detectors and temperature, humidity, motion sensors as well as other security sensors.
NTU-RG-5421GC-Wac device has an integrated RF output, to which a TV is connected to watch analog or digital cable television (if the service is provided
by the carrier).
Models
NTU-RG series devices are designed to support various interfaces and features, see Table 1 .
Table 1 – Models
Model name WAN LAN FXS Z-Wave TV Wi-Fi USB
NTU-RG-5402G-W
1xGPON 41Gigabit 2 - - 802.11n, 2*2 - 300 / – 2,4 1
NTU-RG-5421G-Wac
1xGPON 41Gigabit 1 - - 802.11n, 2*2 - 300 / – 2,4
802.11ac, 2*2 - 866 / – 5 1
NTU-RG-5421GC-Wac
1xGPON 41Gigabit 1 - 1 802.11n, 2*2 - 300 / – 2,4
802.11ac, 2*2 - 866 / – 5 1
NTU-RG-5421G-WZ
1xGPON 41Gigabit 1 1 - 802.11n, 2*2 - 300 / – 2,4
802.11ac, 2*2 - 866 / – 5 1
NTU-RG-5440G-Wac
1xGPON 41Gigabit - - - 802.11n, 2*2 - 300 / – 2,4
802.11ac, 4*4 - 1733 / – 5 1
NTU-RG-5440G-WZ
1xGPON 41Gigabit - 1 - 802.11n, 2*2 - 300 / – 2,4
802.11ac, 4*4 - 1733 / – 5 1
Device Specification
Device is equipped with the following interfaces:
RJ-11 ports to connect network devices (FXS):
2 ports in NTU-RG-5402G-W;
1 port in NTU-RG-5421G-Wac, NTU-RG-5421G-WZ, NTU-RG-5421GC-Wac.
1xPON SC/APC port for connection to provider's network (WAN);
Ethernet RJ-45 LAN ports for connection of network devices (LAN):
4 ports of RJ-45 10/100/1000Base-T.
Wi-Fi transceiver:
11b/g/n for NTU-RG-5402G-W;
11a/b/g/n/ac for NTU-RG-5421G-Wac, NTU-RG-5421G-WZ, NTU-RG-5421GC-Wac , NTU-RG-5440G-WZ, NTU-RG-5440G-Wac.
1xUSB 1 port for external USB or HDD storages.
«Smart Home» controller, forms a part of NTU-RG-5421G-WZ, NTU-RG-5440G-WZ;
1 RF port for cable TV (CaTV) connection for NTU-RG-5421GC-Wac.
The terminal uses an external adapter for 220V/12V power supply.
The device supports the following functions:
Network functions:
bridge or router operation mode;
PPPoE (auto, PAP, CHAP, MSCHAP authorization);
IPoE (DHCP-client and static);
static IP address and DHCP (DHCP client on WAN side, DHCP server on LAN side);
Multicast traffic transmission via Wi-Fi;
DNS (Domain Name System);
DynDNS (Dynamic DNS);
UPnP (Universal Plug and Play);
IPsec (IP Security);
NAT (Network Address Translation);
Firewall;
NTP (Network Time Protocol);
QoS;
IGMP snooping;
IGMP proxy;
Parental Control;
Storage service;
SMB, FTP, Print Server;
VLAN in accordance with IEEE 802.1Q.
Wi-Fi:
support for IEEE 802.11a/b/g/n/ac standards;
Simultaneous dual-band operation: 2.4 GHz and 5 GHz.
VoIP
SIP
Audio codecs: G.729 (A), G.711(A/U), G.723.1;
ToS for RTP packets;
ToS for RTP packets;
Echo cancellation (G.164 and G.165 guidelines);
Voice activity detection (VAD);
Comfort noise generator (CNG);
DTMF signal detection and generation
DTMF transmission (INBAND, RFC2833, SIP INFO)
Fax transmission: G.711, T.38;
Caller ID display.
Value added services (VAS):
Call Hold;
Call Transfer;
Call Waiting;
Forward unconditionally;
Forward on «no answer»;
Forward on «busy»;
Caller ID Display for ETSI FSK;
Anonymous calling;
Warmline;
Flexible dial plan;
Voice mail notifications (MWI);
Anonymous call blocking;
Call Barring;
DND (Do not disturb).
Firmware updates via web interface, TR-069, OMCI.
Remote monitoring, configuration, and setup:
TR-069;
Web interface;
OMCI;
CaTV 1.
Only for
1NTU-RG-5421GC-Wac
The figures below illustrate application schemes of NTU-RG.
Figure 1 – NTU-RG-5402G-W application diagram
Figure 2 – NTU-RG-5421G-Wac, NTU-RG-5421G-WZ, NTU-RG-5440G-Wac and NTU-RG-5440G-WZ application diagram
Figure 3 – NTU-RG-5421G-WZ and NTU-RG-5440G-WZ application diagram
Key Specifications
Table 2 shows main specifications of the terminals:
Table 2 – Main Specifications
VoIP protocols
Supported protocols SIP
Audio codecs
Codecs G.729, annex A
G.711(A/µ)
G.723.1 (5,3 Kbps)
Fax transmission: G.711, T.38
Parameters of Ethernet LAN interfaces
Number of interfaces 4
Connector type RJ-45
Data transfer rate, Mbps Autonegotiation, 10/100/1000 Mbps,
duplex/half-duplex
Standards IEEE 802.3i 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit
Ethernet
IEEE 802.3x Flow Control
IEEE 802.3 NWay auto-negotiation
Parameters of PON interface
Number of interfaces 1
Standards ITU-T G.984.x Gigabit-capable passive optical networks (GPON)
ITU-T G.988 ONU management and control interface (OMCI) specification
IEEE 802.1Q Tagged VLAN
IEEE 802.1P Priority Queues
IEEE 802.1D Spanning Tree Protocol
Connector type SC/APC in accordance with ITU-T G.984.2, ITU-T G.984.5 Filter, FSAN Class B+, SFF-8472
Transmission medium Fiber optical cable SMF - 9/125, G.652
Splitting ratio Up to 1:128
Maximum range of coverage 20 km
Transmitter: 1310 nm
Upstream connection speed 1244 Mbps
Transmitter power from +0,5 to +5 dBm
Optical spectrum width (RMS) 1 nm
Receiver: 1490 nm
Downstream connection speed 2488 Mbps
Receiver sensitivity from -8 to -28, BER1.0x10-10
Receiver optical congestion -8 dBm
Parameters of subscriber analogue ports
Number of ports NTU-RG-5402G-W NTU-RG-5421G-Wac
NTU-RG-5421GC-Wac
NTU-RG-5421G-WZ
2 1
Loop resistance Up to 2 k
Call reception Pulse/frequency (DTMF)
Caller ID display Yes
Wi-Fi interface parameters
Model NTU-RG-5402G-W NTU-RG-5421G-Wac
NTU-RG-5421GC-Wac
NTU-RG-5421G-WZ
NTU-RG-5440G-Wac
NTU-RG-5440G-WZ
Standard 802.11 b/g/n 802.11 a/b/g/n/ac 802.11 a/b/g/n/ac
Frequency range 2400 ~ 2483,5 MHz 2400 ~ 2483,5 MHz, 5150 ~ 5350 MHz, 5650 ~ 5850 MHz
Simultaneous Dual Band
Modulation CCK, BPSK, QPSK, 16 QAM, 64 QAM, 256
QAM CCK, BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM
Data transfer rate, Mbps – 802.11b/g/n: 1-13
– 802.11b: 1; 2; 5.5 and 11 Mbps
– 802.11g: 6, 9, 12, 18, 24, 36, 48 and 54 Mbps
– 802.11n: from 6.5 to 300 mbps (from MCS0
to MCS15)
– 802.11b/g/n: 1-13
– 802.11b: 1; 2; 5.5 and 11 Mbps
– 802.11g: 6, 9, 12, 18, 24, 36, 48 and
54 Mbps
– 802.11ac: 866 Mbps (80 MHz)
– 802.11b/g/n: 1-13
– 802.11b: 1; 2; 5.5 and 11 Mbps
– 802.11g: 6, 9, 12, 18, 24, 36, 48 and
54 Mbps
– 802.11ac: 1733 Mbps (80 MHz)
Maximum transmitter output
power – 802.11b (11 Mbps): 17 dBm
– 802.11g (54 Mbps): 15 dBm
– 802.11n (MCS7): 15 dBm
– 802.11b (11 Mbps): 17 dBm
– 802.11g (54 Mbps): 15 dBm
– 802.11n (MCS7): 15 dBm
– 802.11 (MCS0): 19 dBm
2.4 GHz:
– 802.11b (11 Mbps): 18 dBm
– 802.11g (54 Mbps): 16 dBm
– 802.11n (MCS7): 16 dBm
– 802.11n (MCS0): 18 dBm
5 GHz:
– 802.11ac (MCS7): 18 dBm
– 802.11 (MCS0): 20 dBm
MAC protocol CSMA/CA model of ACK 32 MAC
Security 64/128-bit WEP encryption;
WPA, WPA2
802.1x
AES & TKIP
MIMO 2,4 GHz- 22 2,4 GHz- 22, 5 GHz - 22 2,4 GHz- 22, 5 GHz - 44
Antenna gain 5 dBi
Operating temperature range from +5 to +40°C
Control
Local control Web interface
Remote control Telnet, TR-069, OMCI
Firmware update OMCI, TR-069, HTTP
Access resriction By password
General parameters
Model NTU-RG-5402G-W
NTU-RG-5421G-Wac
NTU-RG-5421G-WZ
NTU-RG-5421GC-Wac NTU-RG-5440G-Wac
NTU-RG-5440G-WZ
Power supply 12 V DC/220 AC power adapter
Max. power consumption 18 W
Operating temperature range From +5 to +40°C
Relative humidity Up to 80%
Dimensions 187x120x32 mm 220x120x50 mm 234x133x34 mm
Weight 0,3 kg 0,45 kg 0,57 kg
Design
Subscriber terminal is designed as desktop device in plastic housing.
The rear panel layout of the device is depicted in Figures 4, 5, 6, 7.
Figure 4 – NTU-RG-5402G-W-Wac rear panel layout
Figure 5 – NTU-RG-5421G-Wac and NTU-RG-5421G-WZ rear panel layout
The connectors and controls located on the NTU-RG-5402G-W, NTU-RG-5421G-Wac and NTU-RG-5421G-WZ rear panel are listed in .Table 3
Table 3 – Description of the connectors and controls on the rear panel
Rear panel element Description
1 On/Off
Power button
2 12V
Power adapter connector
3 PON
SC port (socket) for PON with GPON interface
4 USB
Connector for external drives and other USB devices
5 Phone
RJ-11 connector for analogue phone connection:
2 connectors in NTU-RG-5402G-W
1 connector in NTU-RG-5421G-Wac NTU-RG-5421G-WZ
6 LAN 10/100/1000 1..4
4 RJ-45 ports for connection to network devices
Figure 6 – NTU-RG-5421GC-Wac rear panel layout
Connectors and controls located on the rear panel of the device are listed in .Table 4
Table 4 – Description of the connectors and controls on the rear panel
Rear panel element Description
1 On/Off
Power button
2 12V
Power adapter connector
3 USB
Connector for external drives and other USB devices
4 TV
RF port for connecting a coaxial cable
5 Phone
RJ-11 connector for analogue phone connection
6 LAN 10/100/1000 P1..P4
4 RJ-45 ports for connection to network devices
7
Wi-Fi
Wi-Fi enabling/disabling button
8
WPS
A button which enables automatic secure Wi-Fi connection
9
F
A functional key that reboots the device and resets it to factory settings
10
PON
SC port (socket) for PON with GPON interface
Figure 7 – NTU-RG-5440G-Wac and NTU-RG-5440G-WZ rear panel layout
The connectors and controls located on the NTU-RG-5440G-Wac and NTU-RG-5440G-WZ rear panel are listed in .Table 5
Table 5 – Description of the connectors and controls on the rear panel
Rear panel element Description
1 F
A functional key to reboot the device and reset it to factory settings
2 On/Off
Power button
3 12V
Power adapter connector
4 LAN 10/100/1000 1..4
4 RJ-45 ports for connection to network devices
5 PON
SC port (socket) for PON with GPON interface
6 USB
Connector for external drives and other USB devices
7 Wi-Fi
Wi-Fi enabling/disabling button
8 WPS
A button to enable automatic secure Wi-Fi connection
Figure below shows NTU-RG-5402G-W, NTU-RG-5421G-Wac and NTU-RG-5421G-WZ side panel layout.
Figure 8 – NTU-RG-5402G-W, NTU-RG-5421G-Wac and NTU-RG-5421G-WZ side panel layout
See for detailed information about buttons located on the side panel of the device.Table 6
Table 6 – NTU-RG-5402G-W, NTU-RG-5421G-Wac and NTU-RG-5421G-WZ side panel buttons description
Rear panel element Description
1 Reset
A functional key to reboot the device and reset it to factory settings
2 Wi-Fi
Wi-Fi enabling/disabling button
3 WPS
A button to enable automatic secure Wi-Fi connection
Light Indication
Figure 9 shows NTU-RG-5402G-W, NTU-RG-5421G-Wac and NTU-RG-5421G-WZ top panel layout.
Figure 9 – NTU-RG-5402G-W (on the left) and NTU-RG-5421G-Wac, NTU-RG-5421G-WZ (on the right) top panel layout
Current status of the device is represented by means of indicators paced on the top panel. provides possible statuses of the LEDs.Table 7
Table 7 – Description of NTU-RG-5402G-W, NTU-RG-5421G-Wac and NTU-RG-5421G-WZ top panel LEDs
Top panel element LED status Description
1
– device power and activity status
indicator off device is disconnected from the power source or faulty
red device startup is in progress
green device startup completed, the current device configuration differs from the default one
orange device startup is completed, the default configuration is set
2
– optical interface activity indicator off device booting
green connection between optical line terminal and the device has been established
flashes green connection between optical line terminal and the device has been established (the device is not
activated)
flashes red no signal from optical line terminal
3
– status indicator off Internet interface is not configured
green device is ready for operation, Internet connection is established
flashes green
slowly device firmware update is in progress
flashes green
rapidly device booting/connection to the Internet is being established
4
– FXS port activity indicator
off SIP agent is not configured/not registered/off
on SIP agent is successfully registered
flashes off hook/phone call
5
– Wi-Fi activity indicator for 2.4
2.4
GHz green Wi-Fi network is active
flashes transmitting data via Wi-Fi
off Wi-Fi network is inactive
6
– Wi-Fi activity indicator for 5 GHz
5
green Wi-Fi network is active
Altri manuali per NTU-RG-5402G-W
2
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali ELTEX Hardware di rete
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
