EMC2 Celerra NS-480 System Manuale utente
EMC®Celerra®NS-480 System
(Dual Blade)
Installation Guide
P/N 300-010-732 Rev A01Version 6.0
Copyright © 2008-2010 EMC Corporation. All rights reserved. Published August, 2010
EMC believes the information in this publication is accurate as of its publication date. The information is
subject to change without notice.
THE INFORMATION IN THIS PUBLICATION IS PROVIDED “AS IS.” EMC CORPORATION MAKES
NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WITH RESPECT TO THE
INFORMATION IN THIS PUBLICATION, AND SPECIFICALLY DISCLAIMS IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE.
Use, copy, or distribution of any EMC software described in this publication requires an applicable
software license.
For the most up-to-date regulatory document for your product line, go to the Technical Documentation
and Advisories section on EMC Powerlink. For the most up-to-date listing of EMC product names, see
EMC Corporation Trademarks on EMC.com.
All other trademarks used herein are the property of their respective owners.
The label, settings, and system cabling information in this document are for your reference. Paste the
Control Station label in the provided space.
3
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
Before you begin
!
Primary internal network 128.221.252.100
Backup internal network 128.221.253.100
Netmask 255.255.255.0
IP address of storage processorA 128.221.252.200
IP address of storage processor B 128.221.253.201
Gateway IP address of storage processorA 128.221.252.104
Gateway IP address of storage processor B 128.221.253.104
Internal system addresses Factory values
Welcome
The system you are about to install comes factory pre-loaded with EMC®Celerra®Network Server
software (DART) and CLARiiON®storage array software (FLARE®).
Software upgrade
If you bought a software maintenance contract, you are entitled to software upgrades only after the
installation, Celerra Startup Assistant (CSA), and registration have successfully completed.
Site preparation
Complete the site preparation by verifying the following activities before installation:
• Network connections
• Power requirements
• Rack space requirements
Default IP addresses
The system components communicate with each other using a private Internet Protocol (IP) network.
By default, this network uses the IP addresses listed in the following table.
If your existing IP network uses addresses on these subnets, you are required to change the private
network addresses of your Celerra Network Server to different subnets before the installation.
4
Installation overview
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
This CD contains the intellectual property of
EMC Corporation or is licensed to EMC Corporation
from third parties. Use of this CD and the intellectual
property contained herein is expressly limited to the
terms and conditions of the License Agreement.
EMC® Celerra® NS20
Back Next Cancel
EMC® Celerra® NS20 System
Tutorial
CSA Installation
P/N nnn-nnn-nnn-A0n
EMC®
Tutorial
CSA Installation
P/N nnn-nnn-nnn-A0n
Step 4. Register with the
service provider.
Implementation
Step 3. Install using the
Celerra Startup Assistant.
Step 2. Assemble and cable
the Celerra NS-480 on site.
Step 1. Order the Celerra NS-480
and prepare the site.
Installation
!!
!
!!
Step 5. Configure for production. CNS-001377
5
Installation overview steps
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
Installation steps:
1. Review and complete the Celerra worksheet, pages 29-34, and verify that the site is
properly prepared for the installation of your Celerra NS-480.
About 20 minutes.
2. If your Celerra NS-480 is to be installed in a customer-supplied rack, use this document to unpack
the system from the mini-rack shipping container, remove the reusable rails, and install the system
in your available rack.
About 40 minutes.
Note: If your Celerra NS-480 system arrived at your site in a pre-installed cabinet and is
previously cabled, verify the cabling before you begin the use of your system.
Cable your system according to the instructions and illustrations contained in this document.
Ensure that all of your cables are seated securely.
About 45 minutes.
3. When you install your Celerra NS-480, use the Celerra Startup Assistant (CSA) to pre-configure
your system. The latest version of the CSA can be downloaded from the Celerra Tools section
on Powerlink®. The CSAis also on the Celerra Applications & Tools CD.
About 15 minutes.
4. Register your system with the service provider. If you do not register your system now, using the
Celerra Startup Assistant, your request for support from your service provider will be delayed.
You can also register your Celerra NS-480 by downloading the Registration Wizard on Powerlink.
About 5 minutes.
Implementation step:
5. After you have registered your Celerra NS-480 system, you must configure the system for
production. You can use the Provisioning Wizard in the CSA, one of the several pre-packaged
implementation configurations based on common usages, or your own implementation using
Unisphere to configure your system. At the end of each one of these configurations,
your system will be ready for production.
6
Unpacking the Celerra NS-480 system
If your Celerra NS-480 system was purchased and shipped in an EMC 40 Unit cabinet
(70 in. in height; 1 unit =1.75 in.), start on page 15 of this document and confirm that the cables are
installed correctly and securely; otherwise start unpacking your Celerra NS-480 system from the
disposable mini-rack shipping container.
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
CNS-001386
7
Note: The table represents components that are shipped with Celerra’s disposable mini-rack.
If additional accessory boxes are necessary, they will be shipped separately.
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
CNS-001372Front
Shrink-wrapped Installation Guide,
environmental information
and notices
Disposable mini-rack
Accessory box
Disk-array
enclosure (DAE)
Standby power supply
(SPS)
Control Station (CS)
Blade enclosure
Storage processor enclosure
(SPE)
Ganged
rails
Remove this label and
paste it on the back of
the front cover of this
installation guide.
Ganged rails
Contents of package
Disposable mini-rack Accessory box Document inventory list
Disk-array enclosure Standby power supply
interconnect cable kit
Installation guide with storage
processor options and cabling
diagrams
Control Station Fibre Channel cables
Environmental compliance
information and notices
Standby power supply Power cables
Storage processor enclosure Serial cables
Ganged rails Crossover cables
Blade enclosures:
Blade enclosure 1 area empty
Blade enclosure 0
Ethernet cables for internal network
Bezels
Hardware for non-factory installs
8
Remove ONLY
7 screws
per side.
Remove ONLY
7 screws
per side.
CNS-001384
Ganged rails
Blade enclosure
Standby power supply
Control Station
Storage processor
1
2
3
5
4
Front
Mini-rack
2 Control Station (CS)
4Storage processor
enclosure (SPE)
3 Standby power
supply (SPS)
1Disk-array
enclosure (DAE)
5Blade enclosure
Remove this label and
paste it on the back of
the front cover of this
installation guide.
Disk-array
enclosure
Remove components from shipping container
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
2. Carefully set aside each component as
it is removed from the disposable
mini-rack shipping container.
Caution: Two people are required to remove the components. Only remove screws holding
the components in place at this time. Do not remove the screws holding the rails in place; this
may cause damage to the components. Only remove one component at a time.
3. The ganged rails
remain in the mini-rack shipping
container at this time.
1. Using a Phillips-head screwdriver, remove only 7 screws per side. Keep the removed screws
to install the components in your rack.
!
9
R
e
m
o
v
e
r
a
il
s
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
Remove the screws holding the rails in place. Keep the screws to install the rails in your rack.
Remove the reusable rails from the disposable mini-rack.
Disposable mini-rack
Remove ganged rails
from mini-rack.
CNS-001383MOD
Remove 3 screws
each side.
Remove ganged rails
from mini-rack.
Remove 2 screws
each side.
Front of rack
Rear of rack
Rail slide with extensions
Threaded
screw holes
Ganged rails
Ganged rails
Rail slide with extensions
10
In
sta
ll r
a
il
s
in
to
s
i
te
r
ac
k
For more information, refer to Celerra Tools on http://Powerlink.EMC.com
Note: The rails must be aligned carefully, and two people are required to install the components.
1. Insert the rail slide and seat both rail extensions into the rear channel of your rack. We
recommend placing the top rail pin into the hole just above a U marker.
2. Align the front of the ganged rail as shown. Insert retention screws in the front and
retention screws in the back of each rail. See the following illustration.
3. Do not fully tighten the retention screws at this time. Allow some adjustment space for the
installation of the components.
Install the retaining screws
After inserting the rail
extensions, install 2 screws
on each side of your rack
to hold the rails in place.
Install 3 retaining screws
on each side of your rack
to hold the ganged rails in place.
Front customer rack
Rail slides
1
DAE
2
25
23
22
20
4
27
26
17
14
11
8
12
BE 1
BE 0
SP
SPS
CS
Rear of rack
CNS-001376
Rail slides
1
2
25
23
22
20
4
27
26
17
14
11
8
12
Threaded
screw holes
DAE
BE 1
BE 0
SP
SPS
CS
Ganged rails
Indice
Altri manuali EMC2 Magazzinaggio
EMC2
EMC2 VNX5500 Manuale utente
EMC2
EMC2 VNX Series Manuale del proprietario
EMC2
EMC2 VNXe3100 Manuale utente
EMC2
EMC2 AX100 Series Manuale di istruzioni
EMC2
EMC2 EMC VNX Series Manuale utente
EMC2
EMC2 AX100 Series Manuale utente
EMC2
EMC2 VNX Series Manuale utente
EMC2
EMC2 VNX Series Manuale utente
EMC2
EMC2 VNXe3100 Manuale utente
EMC2
EMC2 AX100 Series Manuale utente
EMC2
EMC2 VNX VNX7500 Manuale del proprietario
EMC2
EMC2 VNX Series Manuale utente
EMC2
EMC2 AX100 Series Manuale utente
EMC2
EMC2 CX3 UltraScale Series Guida all'installazione
EMC2
EMC2 AX100 Series Manuale utente
EMC2
EMC2 Data Domain DD9500 Manuale di installazione e funzionamento
EMC2
EMC2 VxRail E Series Manuale utente
EMC2
EMC2 Data Domain DD9500 Manuale per l'uso e la cura
EMC2
EMC2 AX100 Series Manuale utente
EMC2
EMC2 Data Domain DD2500 Istruzioni per il montaggio
