Emerson Asset Management Tag Manuale utente
Installation, Operation and Maintenance Manual
D104482X012
Asset Management Tag
I
Installation, Operation and Maintenance Manual
D104482X012
Table of Contents
May 2019
Table of Contents
Table of Contents
Section 1: Introduction
1.1 Scope of Manual ............................................................................................ 1
1.2 Description .................................................................................................... 2
1.3 Specications ................................................................................................ 3
1.4 Education Services ........................................................................................ 3
Section 2: Device Information
Section 3: Installation
3.1 Mounting Considerations .............................................................................. 6
3.2 Installing a Casing Mounted Asset Management Tag ..................................... 7
3.3 Installing a Yoke Mounted Asset Management Tag ........................................ 8
3.4 Installing a Universal Mounted Asset Management Tag ................................. 8
Section 4: Related Documents
Section 5: Parts Ordering
Section 6: Kits
Installation, Operation and Maintenance Manual
D104482X012
1
Section 1: Introduction
May 2019
Introduction
Section 1: Introduction
1.1 Scope of Manual
This instruction manual includes product specications, reference materials, installation,
and parts ordering information for the Emerson Asset Management Tag.
The instruction manual also describes using Asset Connect software to access information
on the Asset Management Tag. Refer to the Asset Connect Quick Start Guide for
information on how to use this downloadable application as well as information on
requirements for the reader/writer, and PC or tablet.
Do not install, operate or maintain an Asset Management Tag without being fully trained
and qualied in valve, actuator, valve accessory, and other applicable process equipment
installation, operation, and maintenance. To avoid personal injury or property damage,
it is important to carefully read, understand, and follow all the contents of this manual,
including all safety cautions and warnings. If you have any questions about these
instructions, contact your Emerson sales ofce before proceeding.
Installation, Operation and Maintenance Manual
D104482X012
2Introduction
Section 1: Introduction
May 2019
1.2 Description
Asset Management Tags are intrinsically safe devices which use Radio Frequency
Identication (RFID) technology to allow for digital storage, collection, and identication
of equipment information. Asset Management Tags can be ordered as an accessory on an
assembly or can be purchased individually for existing in-eld equipment to be populated
utilizing Asset Connect software or with the support of your Emerson sales ofce and
service center.
A reader/writer device is needed to communicate with the Asset Management Tag
using UHF RFID wireless technology. Information gathered from the Asset Management
Tag which has been read by the reader/writer will then be shared to the Asset Connect
Software on either a PC or Tablet using Bluetooth wireless technology.
1. Asset Management Tag 2. Reader/Writer
Reader/Writer not available
for sale from Emerson
Automation Solutions
Additional information can
be found in the Quick Start
Guide
3. PC or Tablet
Asset Connect software is
designed specically for
the Asset Management Tag
Compatible with Windows
7 or Windows 10 operating
systems
Bluetooth radio and
applicable drivers must be
installed
Figure 1 Equipment for reading/writing an Asset Management Tag
Installation, Operation and Maintenance Manual
D104482X012
3
Section 1: Introduction
May 2019
Introduction
1.3 Specications
Specications for the Asset Management Tag are listed in table 1.
Table 1. Specications
Temperature Limits Operating: -40°C to 85°C (-40°F to 185°F)
Storage: -40°C to 90°C (-40°F to 194°F)
Operating Frequency 860-960 MHz (Worldwide)
Construction Materials Tag Housing: PPS, Polyphenylene Sulde
Mounting Bracket: 316 SST
Mounting Screws (Tag Housing to Mounting Bracket):
Steel with RoHS Compliant Zinc Chromate
Mounting Styles Casing
Yoke
Universal
Minimum Read/Write Range Distance
20 ft (6.09 m) read range
1 ft (0.30 m) write range
Range dependent on reader/writer selected
Hazardous Area Approvals FM (US/Canada) – Intrinsically Safe (refer to D104401X012)
ATEX – Intrinsically Safe (refer to D104402X012)
IECEx – Intrinsically Safe (refer to D104403X012)
Electrical Classications Type 4X, IP68
Other Standards UHF EPC Class 1 Gen 2
ISO/IED 18000-6C
GS1 EPC TDS 1.6
ATA Spec 2000
SAE AS5678
DIN 40050-9
1.4 Education Services
For information on available courses for the Asset Management Tag, as well as a variety of
other products and services, contact:
Emerson Automation Solutions
Educational Services - Registration
Phone: +1-641-754-3771 or +1-800-338-8158
emerson.com/education
Installation, Operation and Maintenance Manual
D104482X012
4Device Information
Section 2: Device Information
May 2019
Section 2: Device Information
Available elds for stored information on the Asset Management Tag are shown below in
gure 2.
Figure 2 Asset Management Tag Storage Fields
Installation, Operation and Maintenance Manual
D104482X012
5
Section 3: Installation
Asset Management Tags can be ordered as an accessory to be installed on an assembly or
can be purchased for existing in-eld equipment to be populated utilizing Asset Connect
software or with the support of your Emerson sales ofce and service center.
If the Asset Management Tag assembly is being installed on process equipment in the eld,
observe all installation warnings, cautions, and notes provided in the Instruction Manuals
for all applicable equipment.
Figure 3 Asset Management Tag Assembly
WARNING
Avoid personal injury or damage to property from sudden release of pressure or
uncontrolled process uid. Before starting installation on, or removal from, existing in-eld
equipment:
• Always wear protective gloves, clothing, and eyewear when performing any
installation or removal operations to avoid personal injury.
• Follow all warnings, cautions, notes, and instruction procedures provided in the
Instruction Manuals for all applicable equipment to ensure hazardous conditions
are not created.
• If mounting onto or removing from a valve, use bypass valves or completely shut
off the process to isolate the valve from process pressure. Relieve process pressure
on both sides of the valve. Drain the process media from both sides of the valve.
• If mounting onto or removing from an actuator casing, vent the power actuator
loading pressure.
• If mounting onto or removing from other equipment containing process pressure
or process uid, relieve and isolate the equipment from process pressure and drain
process media.
• Use lock-out procedures to be sure that the above measures stay in effect while
you work on the equipment.
• Check with your process or safety engineer for any additional measures that must
be taken to protect against process media.
Installation
Section 3: Installation
May 2019
Installation, Operation and Maintenance Manual
D104482X012
6
Figure 4 Emerson Asset Management Tag shown on a Fisher™ easy-e™ with
Fisher 667 size 45i Actuator and FIELDVUE™ DVC6200 Digital Valve
Controller
The Asset Management Tag is pre-afxed to the bracket and must remain installed as an
assembly for optimal read range. Three mounting styles have been engineered to optimize
read range as well as provide mounting exibility onto a wide range of equipment,
reference table 2 for assembly part numbers.
3.1 Mounting Considerations
• Installation of the Asset Management Tag assembly must take into consideration
line-of-sight when using the reader/writer to communicate.
• To avoid negatively impacting the read/write distance, the Asset Management Tag
assembly should not be obscured by tubing or other metal equipment and should
not be installed such that the wings of the bracket touch any metal surface.
Installation
Section 3: Installation
May 2019
Installation, Operation and Maintenance Manual
D104482X012
7
Figure 5 Casing Mounted Asset Management Tag Assembly
3.2 Installing a Casing Mounted Asset Management Tag
1. Review Mounting Considerations when planning installation location of Asset
Management Tag.
2. When available, mount using a longer casing bolt, and mount below the lower
casing with the bracket pointed downward and facing outward. Reference gures
3 and 4 above.
3. Ensure that mounting of the Asset Management Tag, does not prevent full thread
engagement of the casing bolting. If mounting the tag prevents complete thread
engagement, mount using a longer casing bolt of the same material specication.
4. Ensure casing bolt is tightened per torque specications in the applicable product
instruction manual.
Installation
Section 3: Installation
May 2019
Bracket wing Bracket
Indice
Altri manuali Emerson Controllori
Emerson
Emerson Fisher 2052 Manuale utente
Emerson
Emerson Fisher 92C Manuale utente
Emerson
Emerson CASH VALVE B Series Manuale
Emerson
Emerson Bettis D Series Manuale di istruzioni
Emerson
Emerson Dixell XW60LH Schema elettrico
Emerson
Emerson CASH VALVE B Manuale utente
Emerson
Emerson Dixell iPro Master IPM500D Schema elettrico
Emerson
Emerson EC3 Series Manuale utente
Emerson
Emerson Fisher FIELDVUE DVC6200 SIS Manuale utente
Emerson
Emerson FRANSEL REGAL 3 Manuale utente
Emerson
Emerson FISHER 670 Series Manuale utente
Emerson
Emerson Fisher 657C Manuale utente
Emerson
Emerson TARTARINI FL Series Manuale utente
Emerson
Emerson PACSystems RSTi-EP Manuale utente
Emerson
Emerson EC3-X33 Manuale utente
Emerson
Emerson Fisher L2 Manuale utente
Emerson
Emerson Fisher FIELDVUE DVC6200 SIS Manuale utente
Emerson
Emerson Fisher 667NS Manuale utente
Emerson
Emerson Powerdrive F300 Manuale utente
Emerson
Emerson Fisher M Series Manuale utente
