Emerson Bettis RP3E Manuale utente

Bettis RTS Relay Board (RP3E)

Electric Actuator

Installation, Operation and Maintenance Manual

VCIOM-15746-EN Rev. 1

April 2023

Note

April 2023

Installation, Operation and Maintenance Manual

VCIOM-15746-EN Rev. 1

This page intentionally left blank.

Installation, Operation and Maintenance Manual

VCIOM-15746-EN Rev. 1

Table of Contents

April 2023

Table of Contents

Section 1: Tools

Tools.........................................................................................................................1

Section 2: Material

Material.....................................................................................................................2

Section 3: Installation

Installation................................................................................................................3

Section 4: Programming

Programming............................................................................................................8

Note

April 2023

Installation, Operation and Maintenance Manual

VCIOM-15746-EN Rev. 1

This page intentionally left blank.

Installation, Operation and Maintenance Manual

VCIOM-15746-EN Rev. 1 April 2023

Tools 1

Section 1: Tools

! WARNING

Remove all power supplies before doing the exchange. Always act with caution during

the exchange!

• Needle nose pliers

• Screw driver phillips

• Screw driver at

• Allen key 5

• Socket wrench 5

Figure 1.

April 2023

Installation, Operation and Maintenance Manual

VCIOM-15746-EN Rev. 1

Material

Section 2: Material

• 1x relay board RP3E6A (ID:13009)

• 1x adapter cable (ID:16504)

• 2x steel screw M3x16 (ID:952)

• 3x plastic distance 8 mm (ID:9896)

• 1x plastic screw M3x15 (ID:9895)

• 1x plastic nut M3 (ID:7084)

• 2x lock plates M3 red (ID:13674)

Figure 2.

Figure 3.

Installation, Operation and Maintenance Manual

VCIOM-15746-EN Rev. 1 April 2023

Installation 3

Section 3: Installation

Unscrew the 4 hexagon socket screws from the cover and remove it carefully. Mind the

connection cable between display and logic board.

Figure 4.

Unscrew the 4 cross recessed screws from the existing logic board and afterwards, tilt it

carefully to you.

Figure 5.

April 2023

Installation, Operation and Maintenance Manual

VCIOM-15746-EN Rev. 1

Installation4

Section 3: Installation

Remove carefully the connected cables: ribbon cable and 6-, 8- and 10-pole plugs

(see Figure 6, left image). Afterwards, you can remove the logic board from the control

unit and disconnect the second ribbon cable on the back (see Figure 6, right image).

Figure 6.

Remove the two steel spacers (marked with the black arrows in Figure 7) in the housing.

Figure 7.

Installation, Operation and Maintenance Manual

VCIOM-15746-EN Rev. 1 April 2023

Installation 5

Section 3: Installation

Place the 8 mm plastic spacers on the relay board as shown in the top image of Figure 8.

Insert the M3x16 steel screws through the holes next to the multi-pin connectors in the

logic board as shown in the bottom image of Figure 8. Then line up the screws with the

plastic spacers in the relay board and secure the screws with the red lock plates. For the

third hole, use the plastic screw M3x15 and secure it in place with the plastic nut.

Figure 8.

Connect the relay board with the multi-pin connector from the logic board.

! WARNING

The four pins on the left side must remain disconnected (see Figure 9).

The orientation of the mounting holes on both the logic and relay boards plus the spacers

must be aligned as shown in Figure 9.

Figure 9.

April 2023

Installation, Operation and Maintenance Manual

VCIOM-15746-EN Rev. 1

Installation6

Section 3: Installation

Connect the 10- and 6-pole connectors to the adapter cables, then connect the blue

connectors of the adapter cables to the corresponding connectors on the relay board.

Figure 10.

Altri manuali per Bettis RP3E

Indice

Altri manuali Emerson Controllori

Emerson

Emerson Fisher SR5 Manuale utente

Emerson

Emerson MultiFlex RTU Manuale utente

Emerson

Emerson Bettis PressureGuard Manuale

Emerson

Emerson Double-Acting Series Istruzioni per l'installazione

Emerson

Emerson PCM-22 Manuale utente

Emerson

Emerson E2 Manuale utente

Emerson

Emerson Fisher FIELDVUE DVC6005 Series Guida alla configurazione

Emerson

Emerson Hytork XL26 Guida

Emerson

Emerson SP Manuale utente

Emerson

Emerson Unidrive M700 Manuale utente

Emerson

Emerson FISHER 657NS Manuale utente

Emerson

Emerson Dixell XRB60CHC Schema elettrico

Emerson

Emerson Dixell XR20T Schema elettrico

Emerson

Emerson Rosemount 3490 Series Manuale utente

Emerson

Emerson NELSON HEAT TRACE CM-2201 Manuale utente

Emerson

Emerson Fisher Fieldvue DVC6030f Manuale utente

Emerson

Emerson Yarway Manuale utente

Emerson

Emerson Fisher CS400 Series Manuale utente

Emerson

Emerson Dixell XR10C Istruzioni operative

Emerson

Emerson dixell XW60LT Schema elettrico

Emerson

Emerson Unidrive M101 Manuale utente

Emerson

Emerson Bettis GVO-C Series Manuale di istruzioni

Emerson

Emerson Copeland EV2 Series Guida utente

Emerson

Emerson FISHER 657 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente

3M MicroTouch EX113 Manuale utente