Emerson Bettis SCE300 Manuale utente
Installation, Operation and Maintenance Manual
MAN-02-04-99-0739-EN Rev. 0
July 2020
Bettis SCE300
Logic Board Firmware Upgrade Programmer ICD-U64 Procedure
Installation, Operation and Maintenance Manual
MAN-02-04-99-0739-EN Rev. 0
Notes
July 2020
This page intentionally left blank
i
Installation, Operation and Maintenance Manual
MAN-02-04-99-0739-EN Rev. 0
Table of Contents
July 2020
Table of Contents
Table of Contents
Section 1: Firmware Upgrade
1.1 Tools ............................................................................................................. 1
1.2 ICD-U64 Programmer Preparation ................................................................ 3
1.3 Firmware Update .......................................................................................... 4
1.4 Firmware Upload........................................................................................... 4
1.5 Actuator Settings Checklist ......................................................................... 16
Installation, Operation and Maintenance Manual
MAN-02-04-99-0739-EN Rev. 0
Notes
July 2020
This page intentionally left blank
July 2020
Installation, Operation and Maintenance Manual
MAN-02-04-99-0739-EN Rev. 0
Firmware Upgrade 1
Section 1: Firmware Upgrade
Section 1: Firmware Upgrade
This procedure details how to program rmware on the logic board for the Bettis SCE300
electric actuator using the ICD-U64 Programmer.
1.1 Tools
! WARNING
Installation, conguration, commissioning, maintenance, and repairs must be performed
by approved and qualied personnel only.
NOTICE
Certain nameplates may carry more than one approval, and each approval may have
unique installation/wiring requirements and/or conditions of "safe use", installation, and
maintenance. These special instructions are in addition to and may override the standard
installation procedures. Special instructions are listed by approval type.
To update the rmware of the SCE300 actuators, the following tools are necessary:
• PC with program CSSLOAD-CCS Programmer Control Software installed
(Figure 1). This software can be downloaded from:
http://www.ccsinfo.com/content.php?page=ccsloadsw
• PC with USB Drivers for all CSS programmers/debuggers
• Firmware “F02_63_125_v3_11.X.production”, for models E006, E013 or
latest revision
• Firmware “F02_250_500_v4_12.X.production”, for models E025, E051, E091,
E171 or latest revision
• The Universal programmer ICD-U64 (Figure 2)
• Logic Board or Actuator
• Cable from the ICD-U64 to the processor card rmware programming connector
part number: VA001-692-15
Figure 1
July 2020
Installation, Operation and Maintenance Manual
MAN-02-04-99-0739-EN Rev. 0
Firmware Upgrade2
Section 1: Firmware Upgrade
Figure 2 ICD-U64 CCS Programmer
ICD-U64 USB Cable to PC
ICD-U64 USB Programmer
Coonector (Logic Board Side)
Figure 3 SCE300 Logic Board
Actuator size:
250/E025
500/E051
1000/E091
2000/E171
Programming
connector
Actuator size:
063/E006
125/E013
Table 1. Programming Connector Pinout
Signal ICD-U64 Pinout SCE300 Logic Board J15
Real Time Debugging Pin 1
ICSP Clock Pin 2 Pin 5
ICSP Data Pin 3 Pin 4
GND Ground Pin 4 Pin 3
VDD Power Pin 5 Pin 2
MCLR Pin 6 Pin 1
Large Logic Board Small Logic Board
July 2020
Installation, Operation and Maintenance Manual
MAN-02-04-99-0739-EN Rev. 0
Firmware Upgrade 3
Section 1: Firmware Upgrade
1.2 ICD-U64 Programmer Preparation
The ICD-U64 Programmer has an internal jumper to select multiple options to power the
target board (actuator logic board).
1. ICD-U64 programmer internal jumper selecting 5 V
This conguration allows the ICD-64 Programmer to provide power to the logic board.
This conguration can be used to program the logic board as standalone board or to
program the logic board while installed in the actuator. The rmware upgrade of the logic
board should be successful regardless if the logic board is powered from the actuator
power supply or ICD-U64 programmer.
Jumper select +5 V
2. ICD-U64 no jumper
The ICD-U64 internal jumper is not present or was set to no power the target board. It's
not possible to upgrade rmware in the logic board as a standalone board since no power
is being supplied to the target board. If the logic board is installed in the actuator, the
actuator requires to be powered on to have a successful rmware upgrade. Note that a
new programming tool will likely have this no voltage setting.
No jumper, or jumper selecting middle pin only
3. ICD-U64 programmer internal jumper selecting 3.3 V
This option must not be selected, it is not applicable for the SCE300 actuator.
July 2020
Installation, Operation and Maintenance Manual
MAN-02-04-99-0739-EN Rev. 0
Firmware Upgrade4
Section 1: Firmware Upgrade
1.3 Firmware Update
After downloading the new rmware, the actuator settings will return to their default
values. As such, the settings in place prior to the rmware download will need to be set
again. For this reason, be sure to store the actuator settings (e.g. opening speed, closing
speed, % opening torque, % closing torque). Refer to Section 6.2 (Local Conguration of
the SCE300) in the actuator IOM for details. To be clear, all settings will be returned to the
factory default values, it is necessary to reset the open/close travel limits; also, the motor
will default to the smallest size.
If not correctly reset the unit will alarm in open torque.
OM1 settings are not required to be reset because they are unaffected by the processor
card rmware ash.
1.4 Firmware Upload
This procedure is based on the CCS Inc. CCSLOAD ICD-U64 programming tool- This tool can
power the microprocessor from the USB port of the PC, using the 5 V setting and also from
the actuator, using the actuators power source. The microprocessor to be ashed is referred
to as the “target”. Take care that the target is only powered from one source, not both.
In some eld installations is difcult to remove power from the actuator, this procedure
provides instructions in how to download rmware without removing the power from the
actuator, therefore instructions in the procedure must be followed to avoid any damage to
the actuator or any personal injury.
1. It is necessary to identify the position of the jumper inside the ICD-U64
programmer before downloading rmware as indicated in step 1.2.
2. To program the logic board as standalone board, connect the ICD-U64
programmer as shown in the picture and proceed in step 9.
July 2020
Installation, Operation and Maintenance Manual
MAN-02-04-99-0739-EN Rev. 0
Firmware Upgrade 5
Section 1: Firmware Upgrade
3. To program the logic board as part of an actuator with no OM1 board present,
carefully connect the ICD-U64 programmer as shown in the pictures and proceed
in step 9.
Figure 4
4. To program the logic board as part of an actuator with an OM1 board present,
and the actuator is powered ON.
! CAUTION
Accessing the electronics compartment while the actuator is in service exposes the
technician to lethal voltage and possibly from more than one source.
Set the OM1 switch SW4 in ON position, it will prevent the actuator from stroking during
rmware download, and it will allow to maintain the actuator in the last position requested
by the 4 - 20 mA or the 0-10 V loop control.
Switch SW4 in
ON position
July 2020
Installation, Operation and Maintenance Manual
MAN-02-04-99-0739-EN Rev. 0
Firmware Upgrade6
Section 1: Firmware Upgrade
5. Note the position then remove the yellow position indicator to allow the OM1
board to be slightly moved to the side and have access to the programming
connector found in the actuator logic board.
6. Carefully remove the 4 screws that are holding the OM1 board. If the actuator is in
vertical position, there is a risk of dropping the screws inside the actuator. Dropping
the screws inside the actuator could cause a short circuit if the screws drop in the
power board, or a damage of the gears if the screws drop in the gears section.
OM1 board
screws
Altri manuali per Bettis SCE300
1
Indice
Altri manuali Emerson Controllori
Emerson
Emerson Bettis GTD Series Istruzioni operative
Emerson
Emerson PACSystems RX3i Manuale utente
Emerson
Emerson Aventics 617 Series Manuale utente
Emerson
Emerson PCM-22 Manuale utente
Emerson
Emerson DL8000 Manuale utente
Emerson
Emerson Fisher 785C Manuale utente
Emerson
Emerson Fisher 667 30 Manuale utente
Emerson
Emerson Dixell XM670K Schema elettrico
Emerson
Emerson KEYSTONE OM13 EPI-2 Manuale utente
Emerson
Emerson Tartarini PRX Series Manuale utente
Emerson
Emerson CASH VALVE A-32 Manuale utente
Emerson
Emerson Fisher FIELDVUE DVC2000 Guida alla configurazione
Emerson
Emerson Bettis BHH Series Manuale utente
Emerson
Emerson MR98 Series Manuale utente
Emerson
Emerson Fisher FIELDVUE DVC6200 SIS Manuale utente
Emerson
Emerson Fisher 2503 Manuale utente
Emerson
Emerson AMPGARD RVSS Manuale utente
Emerson
Emerson Dixell iPro Master IPM500D Schema elettrico
Emerson
Emerson Fisher 627 Manuale utente
Emerson
Emerson Bristol ControlWave LP Manuale operativo
