Emerson EIM TEC2 500 Manuale utente
Quick-Start Guide
E2K-210-05-18 Rev. 3
September 2018
EIM TEC2 Electric Actuator with
Model 500 Quick-Start Guide
(Model 500 Discontinued)
Welcome to TEC2
September 2018
Quick-Start Guide
E2K-210-05-18 Rev. 3
1Welcome to TEC2
Welcome to TEC2
The TEC2 actuator’s Local Display Module (LDM) and Remote Display Module (RDM) provide easy-to-read
actuator information.
The screen graphics will display the mode of operation, valve status, position, torque, and alarm symbols.
The message center will display actuator setup options, data entry feedback, and alarm messages.
Once you follow the simple steps outlined in this guide, the actuator will be ready for normal operation.
The bar graph, position digits, icons, and LEDs will indicate the valve status.
LED Indicators
Valve Torque
Display Diagnostic
Operating
Mode
Moving Status
Welcome to TEC2 Quick-Start Guide
E2K-210-05-18 Rev. 3
September 2018
2Welcome to TEC2
Factory Settings
The actuator has been congured as specied in the order. No further changes should be necessary other than
setting the position limits, and, if network controlled, setting a unique network address. If full data was not
provided when ordering or if changes are needed, see the TEC2 Installation & Operation Manual
(E2K-420-0117), which can be found at www.emerson/eim.
Power Actuator
Verify the voltage rating on the unit nameplate. Connect power to the unit.
Are Position Limits Set?
Does “SET LIMITS BEFORE OPERATING,” “EE%,” and the alarm icon appear, and is the yellow LED
blinking? If so, then position limits have not been set.
Setting Valve Position Limits Initially
September 2018
Quick-Start Guide
E2K-210-05-18 Rev. 3
3Setting Valve Position Limits Initially
Setting Valve Position Limits Initially
2 3 4
YES LOCAL
YES,
NO,
YES,
NO
Release
quickly.
1
STOP
Place the selector knob in the STOP position. Then toggle the control knob in rapid succession to YES, then
NO, then YES, then NO and release. The Setup icon will be displayed on the display module and “SETUP?” will
be displayed on the message center. Rotate the control knob to “YES.” The message center will display “SET
LIMITS BEFORE OPERATING.” Set position limits as described on the next pages.
Setting Position Limits for Electrical Operation Quick-Start Guide
E2K-210-05-18 Rev. 3
September 2018
4Setting Position Limits for Electrical Operation
Setting Position Limits for Electrical Operation
STEP 1: CLOSED Valve Position
234
YES
LOCAL CLOSE
Hold until
desired
position is
reached.
1
STOP
Turn the selector knob to the “LOCAL” position. Hold the control knob in the “CLOSE” position until desired
position is reached. Dis-engage motor drive by setting the declutch lever in “HAND” mode.
Using handwheel, move the valve in the open direction for one handwheel turn to allow for motor coasting.
Re-engage motor drive by setting the declutch lever out of “HAND” mode.
Return the selector knob to the “STOP” position. Select “YES” to set new close limit.
Setting Position Limits for Electrical Operation
September 2018
Quick-Start Guide
E2K-210-05-18 Rev. 3
5Setting Position Limits for Electrical Operation
Setting Position Limits for Electrical Operation
STEP 2: OPEN Valve Position
Turn the selector knob to the “LOCAL” position. Hold the control knob in the “OPEN” position until
desired position is reached. Dis-engage motor drive by setting the declutch lever in “HAND” mode. Using
handwheel, move the valve in the close direction for one handwheel turn to allow for motor coasting. Re-
engage motor drive by setting the declutch lever out of “HAND” mode.
Return the selector knob to the “STOP” position. Select “YES” to set new open limit.
234
YES
LOCAL OPEN
Hold until
desired
position is
reached.
1
STOP
Setting Position Limits for Manual Operation Quick-Start Guide
E2K-210-05-18 Rev. 3
September 2018
6Setting Position Limits for Manual Operation
Setting Position Limits for Manual Operation
STEP 1: CLOSED Valve Position
Turn the selector knob to the LOCAL position. At the “CLOSE VALVE THEN SELECT STOP” prompt, depress the
declutch lever while rotating the handwheel until the clutch is fully engaged. Release the lever.
When the valve is fully closed. Return the selector knob to the STOP position.
At the “ACCEPT CLOSE LIMIT” prompt, select “YES.”
Advance to the “SAVE CHANGES?” prompt and answer YES to save the changes.
2 3 4
YES
LOCAL
1
STOP
5
Depress
declutch,
rotate
handwheel
until...
declutch is fully
engaged.
Release
declutch,
Setting Position Limits for Manual Operation
September 2018
Quick-Start Guide
E2K-210-05-18 Rev. 3
7Setting Position Limits for Manual Operation
Setting Position Limits for Manual Operation
STEP 2: OPEN Valve Position
Turn the selector knob to the LOCAL position. At the “OPEN VALVE THEN SELECT STOP” prompt, depress the
declutch lever while rotating the handwheel until the clutch is fully engaged. Release the lever.
When the valve is fully opened. Return the selector knob to the STOP position.
At the “SAVE LIMITS” prompt, select “YES.”
Advance to the “SAVE CHANGES?” prompt and answer YES to save the changes.
2 3 4
YES
LOCAL
1
STOP
5
Depress
declutch,
rotate
handwheel
until...
declutch is fully
engaged.
Release
declutch,
Check the Open/Closed Settings Quick-Start Guide
E2K-210-05-18 Rev. 3
September 2018
8Check the Open/Closed Settings
Check the Open/Closed Settings
Valve Closed
As you operate the valve in the close direction, verify
that the green LED is blinking. When fully closed is
reached, verify that the green LED stays ON and 0%
is displayed.
1When turning to close,
green LED blinks.
2When fully closed,
green LED remains lit.
Valve Open
As you operate the valve in the open direction, verify
that the red LED is blinking. When fully open is
reached, verify that the red LED stays ON and 100%
is displayed.
1When turning to
open, red LED blinks.
2When fully open,
red LED remains lit.
Note
It is also congurable to have a red LED for
Valve Closed.
Note
It is also congurable to have a green LED for
Valve Open.
Indice
Altri manuali Emerson Controllori
Emerson
Emerson EC2-552 Manuale utente
Emerson
Emerson Bristol ControlWave LP Manuale operativo
Emerson
Emerson Damcos KC 65 Manuale utente
Emerson
Emerson A36 Manuale
Emerson
Emerson Dixell Wing XW570K Schema elettrico
Emerson
Emerson Fisher 95L Manuale utente
Emerson
Emerson CBA730 Istruzioni per l'installazione
Emerson
Emerson PACSystems RSTi-EP EPSCPE100 Manuale utente
Emerson
Emerson Bettis RGS Q-Series Manuale utente
Emerson
Emerson Bettis CBA*30-SR series Istruzioni operative
Emerson
Emerson Bettis XTE3000 Manuale utente
Emerson
Emerson unidrive sp Manuale utente
Emerson
Emerson EC2-311 Manuale utente
Emerson
Emerson Fisher EZR series Manuale utente
Emerson
Emerson Fisher Accu-Pressure Y693 Manuale utente
Emerson
Emerson E2 RX Series Manuale utente
Emerson
Emerson EXD-HP1 Manuale utente
Emerson
Emerson Dixell XR70CX Schema elettrico
Emerson
Emerson Fisher L2 Manuale utente
Emerson
Emerson EC20 Series Manuale utente
