Emerson PACSystems RX3i IC695CPE302 Manuale utente
PACSystems™ RX3i Central Processing
Unit IC695CPE302
Quick Start Guide
GFK-3038C
i PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C
Contents
User Features.........................................................................................1
Switches................................................................................................3
Switch Operation ..................................................................................3
Real-Time Clock Battery ........................................................................4
Ethernet Port.........................................................................................4
Serial Port..............................................................................................5
Removable Data Storage Devices (RDSDs).............................................5
Energy Pack...........................................................................................6
Light-Emitting Diode Indicators (LEDs)..................................................6
Hardware Installation............................................................................9
Initial Checks ..............................................................................................................9
Installation Location..................................................................................................10
Installation in Hazardous Areas ...........................................................11
Class 1 Division 2 Groups ABCD..............................................................................11
ATEX Zone 2............................................................................................................12
Module Installation .............................................................................12
Module Initial Startup..........................................................................13
Initial Configuration...................................................................................................14
Additional Information...............................................................................................16
General Contact Information.....................................................................................17
1 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C
User Features
The PACSystems™RX3i CPE302 can be used to perform real time control of
machines, processes, and material handling systems. The CPU
communicates with the programmer via the internal Ethernet port or a
serial port. It communicates with I/O and Intelligent Option modules over a
dual PCI/Serial backplane.
▪Supports an updated OPC stack and encrypting connections
▪Supports PME’s new GUI management interface for OPC UA configuration
integration (start, stop, restart, clear, and provisioning mode)
▪Supports the new PAC Security tool available for certificate trust management
of clients and servers
▪Contains 5 Mbytes of user memory and 5 Mbytes of non-volatile flash user
memory
▪Supports Battery-less retention of user memory
▪Configured with an Energy Pack IC695ACC400 to power the CPU long enough
to write user memory to non-volatile storage (NVS) on system power loss
▪Equipped with configurable data and program memory
▪Supports programming in Ladder Diagram, Structured Text, Function Block
Diagram, and C
▪Supports auto-located Symbolic Variables that can use any amount of user
memory
▪Equipped with reference table sizes to include 32 Kbits for discrete %I and %Q
and up to 32Kwords each for analog %AI and %AQ
2 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C
▪Supports most Series 90-30 modules and expansion racks. For supported I/O,
Communications, Motion, and Intelligent modules, refer to the PACSystems
RX3i Hardware and Installation Manual, GFK-2314
▪Supports up to 512 program blocks (Maximum size for a block is 128KB)
▪Configured with an RS-232 serial port
▪Enabled with an embedded Ethernet interface to support up to 32
simultaneous SRTP Server connections, up to 16 simultaneous Modbus/TCP
Server connections, and up to 16 simultaneous communications channels of
either SRTP Channels or Modbus/TCP Client channels. For details, refer to the
PACSystems RX3i TCP/IP Ethernet Communications User Manual, GFK-2224
▪Supports OPC UA
▪Supports Ethernet Global Data, Class 1
▪Supports HART®Pass Through
▪Time synchronization to SNTP Time Server on Ethernet network when used
with a rack-based Ethernet module (IC695ETM001) version 5.0 or later
▪Enhanced ability to display serial number and date code in PME’s Device
Information Details.
▪Ability to transfer applications to and from USB 2.0 A type removable data
storage devices, or RDSDs.
▪Compliant with EU RoHS Directive 2002/95/EC using the following
exemptions identified in the Annex: 7(a), 7(c)-I and III, and 15.
HART® is a registered trademark of the HART Communication Foundation of Austin, Texas USA.
Any use of the term HART hereafter in this document, or any document referenced by this
document, implies the registered trademark.
3 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C
Switches
The RDSD and Run Mode switches are located behind the front protective
door. The Reset switch is not used. Switch operation is given in the
following table.
Switch Operation
RDSD Switches
Function
Start pushbutton
Pressing this switch initiates RDSD data transfer. (The
three-position switch must be set to Upload or
Download.)
Three-position switch
Enables/disables RDSD data transfer and selects the
direction of data transfer.
Upload
Loads application from CPU to RDSD.
Off
Disables RDSD data transfer.
Download
Stores application from RDSD to CPU.
Run Mode Switch
A three-position switch which operates as follows:
Switch Position
CPU and Sweep Mode
Memory Protection
Run I/O Enable
The CPU runs with I/O sweep
enabled.
User program memory is
read only.
Run Output Disable
The CPU runs with outputs
disabled.
User program memory is
read only.
Stop
The CPU is not allowed to go
into Run mode.
User program memory
can be written.
The Run Mode switch can be disabled in the programming software in Hardware
Configuration (HWC). The switch’s memory protection function can be disabled
separately in HWC. The Run Mode switch is enabled by default. The memory
protection functionality is disabled by default.
4 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C
Real-Time Clock Battery
The CPE302 is shipped with a real time
clock (RTC) battery (IC690ACC001)
installed, with a pull-tab on the battery.
The pull tab should be removed before
installing the CPE302.
There are no diagnostics or indicators to
monitor RTC battery status. The RTC
battery has an estimated life of 5 years
and must be replaced every 5 years on a
regular maintenance schedule. If the RTC
battery fails, the CPU date and time is
reset to 12:00 AM, 01-10-2000 at startup.
The CPU operates normally with a failed
or missing RTC battery; only the initial
CPU Time-of-day (TOD) clock information
will be incorrect.
Figure 1: Real-Time Clock
Battery
Ethernet Port
The embedded Ethernet interface supports communications with the
Machine Edition programming software using the proprietary SRTP
protocol. The CPE302 CPU provides two SRTP server connections.
The embedded Ethernet interface has one RJ-45 Ethernet port that
automatically senses the data rate (10 Mbps or 100 Mbps), duplex status
(half or full duplex), and cabling arrangement (straight through or
crossover) of the attached link.
5 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C
Serial Port
The CPE302 provides one RS-232 serial interface to external devices. This
port can be used for firmware upgrades. The port is electrically isolated. For
serial port pin assignments and details on serial communications, refer to
the PACSystems RX3i CPU Reference Manual, GFK-2222.
The RS-232 port does not supply the 5 VDC power offered by other RX3i
and Series 90-30 CPUs. Cable IC693CBL316 must be used for RS-232 serial
connections to the CPE302.
Removable Data Storage Devices
(RDSDs)
The CPE302 provides the ability to transfer applications to and from an
RDSD (USB compatible device, such as a memory stick, smart phone, digital
camera or MP3 device). Once the data is copied to the RDSD, it can be
written to other RX3i CPE302 CPUs with no programmer software needed.
The RDSD interface requires a user-supplied flash memory device that
complies with the USB 2.0 Specification.
The USB port must be enabled in the RX3i configuration in order to transfer
data between the CPU and the RDSD. The CPE302 is shipped with the RDSD
(USB) port enabled. Complete details of the use of RDSDs are found in the
PACSystems RX3i CPU Reference Manual, GFK-2222.
6 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C
Energy Pack
The CPE302 preserves user memory using an Energy Pack without the need
to periodically replace batteries. The IC695ACC400 Energy Pack powers the
CPU long enough for the CPU to write its user memory contents to the
CPU’s non-volatile storage during a system power loss. Installation of the
Energy Pack is found below.
Light-Emitting Diode Indicators (LEDs)
OK —indicates module readiness to perform normal operations.
Green, ON
steady
CPU passed power-up diagnostics, functioning
properly
OFF
Power is not applied, or CPU has a problem,
which may be indicated by RN and EN blink
pattern
Green, blinking
CPU in Stop-Halt state; possible watchdog
timer fault. Refer to the fault tables. If the
programmer cannot connect, cycle power
with a charged Energy Pack attached and refer
to fault tables
RN —indicates the run state of the CPU.
Green, ON
steady
CPU is in Run mode.
OFF
CPU is in Stop mode.
7 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C
Green,
blinking in
unison with
OK
CPU is in boot mode and is waiting
for a firmware update through a
serial port.
EN —indicates outputs enabled.
Green, ON
steady
Output scan is enabled.
OFF
Output scan is disabled.
CM —indicates activity on the serial communications port.
Green, blinking
Signal activity on the COM1 port.
OFF
No activity on COM1 port.
IO FORCE —indicates override on a bit reference.
Amber, ON
steady
Override active on at least one-bit reference.
OFF
No overrides applied.
STATUS —indicates Energy Pack status.
OFF
Energy Pack not connected.
Green, blinking
Energy Pack charging; not yet charged
above the
minimum operating voltage.
Red, ON
Energy Pack circuit fault.
8 PACSystems™ RX3i Central Processing Unit IC695CPE302 GFK-3038C
Red, blinking
Energy Pack near its end of life and should
be
replaced soon.
Green, ON
steady
Energy Pack is charabove its minimum
operating voltage.
SYS FLT —indicates presence of a fatal fault.
OFF
No fatal faults.
Red, ON
CPU is in Stop/Faulted mode because a
fatal fault
has occurred.
RDSD —indicates signal activity on the RDSD/COM2/USB port.
Green, blinking
COM2 port activity
OFF
No COM2 port activity
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Emerson Controllori
Emerson
Emerson Fisher Fieldvue DVC6030f Manuale utente
Emerson
Emerson Fisher M Series Manuale utente
Emerson
Emerson Bettis Q series Manuale utente
Emerson
Emerson CASH VALVE B Series Manuale
Emerson
Emerson FISHER T208 Series Manuale utente
Emerson
Emerson Fisher 310A-32A-32A Manuale utente
Emerson
Emerson FISHER T208VR Series Manuale utente
Emerson
Emerson E2 Manuale utente
Emerson
Emerson Fisher 67CS Manuale utente
Emerson
Emerson Dixell XR70T Schema elettrico
Emerson
Emerson CASH VALVE A-360 Manuale
Emerson
Emerson Fisher FIELDVUE DVC6200 SIS Manuale utente
Emerson
Emerson Fisher 627B Series Manuale utente
Emerson
Emerson Fisher 161AY Series Manuale utente
Emerson
Emerson Fisher easy-Drive 200R Manuale utente
Emerson
Emerson FL Manuale utente
Emerson
Emerson EC3-P32 Manuale utente
Emerson
Emerson Fisher 1098-EGR Manuale utente
Emerson
Emerson Fisher 299H Manuale utente
Emerson
Emerson Fisher 1052 Manuale utente
