Emerson USB Fieldbus Interface Manuale utente
USB Fieldbus Interface
User’s Manual
User’s Manual
A 7060MNL, Rev 1
June 2012
Copyright
© Emerson Process Management, 2012. All rights reserved. Printed in the USA.
Trademarks
The Emerson logo is a trademark and service mark of Emerson Electric Co.
AMS is a mark of one of the Emerson group of companies.
FOUNDATION™ is a mark of the Fieldbus Foundation of Austin, Texas, USA.
Microsoft and Windows are registered trademarks of the Microsoft Corporation in the
United States and/or other countries.
All other marks are property of their respective owners.
Contents
Chapter 1: Introduction .................................3 Chapter 6: Troubleshooting .........................38
Chapter 2: USB Fieldbus Interface ..................5 Appendix A: Approvals and
certifications ................................................41
Chapter 3: Software installation and device
setup ...........................................................10 Appendix B: Specifications ...........................42
Chapter 4: Using the Fieldbus Device
Configuration utility ....................................22 Appendix C: Waste disposal .........................43
Chapter 5: Using with AMS Device
Manager ......................................................30 Appendix D: Removing pre-release version of
drivers on a Windows XP operating
system .........................................................44
User's Manual June 2012
2
1 Introduction
This manual will guide you in using the USB Fieldbus Interface (interface).
Included here are basic setup, configuration, and troubleshooting
information, as well as guidelines on how to use the interface with AMS Suite:
Intelligent Device Manager.
This manual is divided into the following sections:
•Chapter 1: Introduction – contains safety messages and information
about the manual.
•Chapter 2: USB Fieldbus Interface – contains information about the
interface, its parts, usage, and features.
•Chapter 3: Software installation and device setup – contains
system requirements, software installation instructions, and device
setup information.
•Chapter 4: Using the Fieldbus Device Configuration utility –
contains information on how to use the utility to power, commission,
and/or configure parameters of fieldbus devices.
•Chapter 5: Using with AMS Device Manager – contains setup
information and instructions in using the interface with AMS Device
Manager to configure fieldbus devices.
•Chapter 6: Troubleshooting – contains solutions to the most
common operating problems.
•Appendix A: Approvals and certifications – contains certifications
and approval information.
•Appendix B: Specifications – contains specifications such as
operating temperature, software, electrical information, and
environmental considerations.
•Appendix C: Waste disposal – contains the interface disposal
guidelines.
•Appendix D: Removing pre-release version of drivers on a
Windows XP operating system – contains instructions on how to
remove previous driver versions.
June 2012 User's Manual
3
1.1 Safety message
WARNING!
Do not connect the USB Fieldbus Interface to a live segment (with an active DCS Host and power
supply attached) if the power indicator light on the interface is amber in color. Doing so can disrupt
communications and may compromise automation safety.
User's Manual June 2012
4
2 USB Fieldbus Interface
Topics covered in this chapter:
•Overview
•Parts and function
•Power modes
2.1 Overview
The USB Fieldbus Interface enables two-way communication between a
computer and fieldbus devices. Its primary function is to allow the setup,
configuration, monitoring, and troubleshooting of fieldbus devices through a
computer.
The interface is fully compatible with all FOUNDATION fieldbus (FF) devices
and is always configured as a "visitor."
Features
Compliant with USB 1.1 and USB 2.0 specifications
Works with standard USB cables
Can detect a Link Active Scheduler (LAS) and will take over as LAS if it is not present on the
segment
Can be connected to any fieldbus segment containing a FOUNDATION fieldbus device
It is particularly useful in these plant scenarios:
•Workbench setup and troubleshooting of fieldbus devices
•With a laptop in the field to configure, commission, decommission, or
troubleshoot fieldbus devices
June 2012 User's Manual
5
The USB Fieldbus Interface comes with a USB cable, lead set, user's manual*,
and installation CD*.
Box contentsFigure 2-1:
User's Manual June 2012
6
2.2 Parts and function
The USB Fieldbus InterfaceFigure 2-2:
1 Field connection indicator light (*) Indicates the fieldbus device connection status
2 Power indicator light (*) Indicates the power mode of the interface
3 USB port B-type receptacle, compliant with USB 1.1 and 2.0
specifications
4 Fieldbus device connection socket Banana-type connection, compatible with the lead set
provided
(*) See the following Indicator Light Scenarios table.
June 2012 User's Manual
7
Indicator Light ScenariosTable 2-1:
Power
indicator
light
Field
connection
indicator light
Scenarios
Normal scenarios
Green Green The USB Fieldbus Interface is connected to an externally
powered segment and it is able to communicate.
Amber Green The USB Fieldbus Interface is providing power to a fieldbus
segment and it is able to communicate.
Other scenarios
Off Off
The USB Fieldbus Interface is not connected to a powered
computer.
-OR-
The USB Fieldbus Interface is connected to a computer but
the computer power is off.
-OR-
The USB FF HSE Server is not running on the connected
computer.
Green Off
The USB Fieldbus Interface is not connected to a powered
segment.
-OR-
The USB Fieldbus Interface is connected to a powered
segment with the wrong polarity.
Off Green The USB Fieldbus Interface is connected normally to a
powered segment but the USB FF HSE Server is not running.
Amber Red The USB Fieldbus Interface is providing power but a short
circuit has been detected on the field connection.
Amber Off
The USB Fieldbus Interface is providing power and
connected to an already powered fieldbus segment with
reverse polarity.
Amber Amber
The USB Fieldbus Interface is providing power to a fieldbus
segment and the load on that segment has exceeded its
limit.
User's Manual June 2012
8
2.3 Power modes
The USB Fieldbus Interface is capable of working in two power modes:
•Mode 1 - The interface does not supply power to the connected
fieldbus device or segment. The fieldbus device or segment is
powered by an external source.
Mode 1 is the default mode.
•Mode 2 - The interface powers the connected fieldbus device or
segment and no external power is needed.
The interface is capable of powering multiple devices on a fieldbus
segment through an external USB hub. It can provide current of up to
85 mA (typically three or four fieldbus devices on the same segment).
You can configure Mode 2 using the Fieldbus Device Configuration
utility. For more information, see Section 4.3.
Note
You can choose to use only one power mode. Never attempt to use two power sources at the same
time as it can disrupt communications and may compromise automation safety.
June 2012 User's Manual
9
3 Software installation and device setup
Topics covered in this chapter:
•System requirements
•Installing the Fieldbus Device Configuration utility
•Installing drivers manually
•Setup and connection
•Connecting to a live fieldbus segment
3.1 System requirements
Operating system (*)
Windows 7 (32- or 64-bit)
Windows XP Home or Professional (32-bit) SP3
Hard disk space
At least 500MB disk space
Hardware
USB 1.1 or USB 2.0 port
3.2 Installing the Fieldbus Device Configuration utility
Notes
•Do not connect the USB Fieldbus Interface to the computer or to a fieldbus device or
segment until software installation is complete.
•You may be prompted to determine the operating system and the Windows version (32-
bit or 64-bit) running on your computer. Keep this information handy.
1. Insert the installation CD into the CD drive of your computer.
Software and driver installation should start automatically.
If AutoRun is not enabled, run setup.exe from the installation CD.
(*) administrator mode required
User's Manual June 2012
10
Altri manuali per USB Fieldbus Interface
2
Indice
Altri manuali Emerson Apparecchiature di registrazione
Emerson
Emerson QuickPanel+ IC755C S06RD Series Manuale utente
Emerson
Emerson USB Fieldbus Interface Manuale utente
Emerson
Emerson Keystone OM9 - EPI2 Manuale utente
Emerson
Emerson AE4-1395 Manuale
Emerson
Emerson Bettis RTS Manuale utente
Emerson
Emerson IEC 62591 Manuale utente
Emerson
Emerson ROSEMOUNT Analytical SPS 4000 Series Manuale utente
Emerson
Emerson Blue Wireless Easy Install 1F98EZ-1621 Manuale utente
Emerson
Emerson SPS 4001B Manuale utente
Emerson
Emerson Keystone OM9 Istruzioni per l'installazione e il funzionamento
Manuali Apparecchiature di registrazione popolari di altre marche
Strymon
Strymon NIGHTSKY Manuale utente
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente
Tews Technologies
Tews Technologies TPMC465 Manuale utente
Honeywell
Honeywell Excel 50 Manuale utente
SeaLevel
SeaLevel COMM+8.LPCI Manuale utente
Arturia
Arturia AUDIOFUSE STUDIO Manuale utente
