Emerson SSW Series Manuale utente

Uninterruptible Power Supply

User Manual

SSW UPS Series

CONTENTS

What's Included. . . . . . . . . . . . . . . . . . . . . . . 1

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . 1

2.0 Important Safety Instructions . . . . . . . . . . . . . . 2

3.0 General Description . . . . . . . . . . . . . . . . . . . 3

4.0 System Block Diagrams . . . . . . . . . . . . . . . . . 5

5.0 Installation and Operation. . . . . . . . . . . . . . . . 6

6.0 LCD Screen Diagnostics . . . . . . . . . . . . . . . . . 7

7.0 Battery Replacement . . . . . . . . . . . . . . . . . 10

8.0 Troubleshooting . . . . . . . . . . . . . . . . . . . 15

9.0 Technical Specifications . . . . . . . . . . . . . . . . 16

Technical Support . . . . . . . . . . . . . . . . . . . . . 18

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 18

Page: 1

What's Included

The UPS is shipped with the following items:

• User manual

• USB cable: High speed 2.0 Standard Type A-B, 6 ft (1.8 m)

NOTE: UPSwatch - Power Monitoring and Control Software is available for download at www.solahd.com.

The software is compatible with: Windows 7, 8, 10, Windows 2008, 2012, 2016, Windows 2008/2012

Server Core, Hyper-V 2008/2012, Linux OpenSUSE 11.4, Linux ubuntu 10.04, Linux Fedora 3.1.9, CentOS 5.8,

Citrix XenServer 6.0.0, Linux KVM.

Accessory (Optional)

• SSWSNMPCARD: SNMP card for SSW1500 models only. This SNMP card provides an advanced,

yet easy-to-use network management function which supports both SNMP and HTTP. Features include:

multiple system shutdown, event notication, scheduling, and control and conguration of the UPS

remotely. The SNMP card must be inserted into the Communication Port on the rear panel of the UPS.

Please visit www.solahd.com for more information.

1.0 Introduction

Thank you for selecting the SSW Uninterruptible Power System. This manual contains important safety

instructions that should be folllowed during the installation and operation of your UPS.

• Please read all safety, installation and operating instructions before attempting to install or operate

the UPS.

• Please adhere to all warnings on the unit and in this manual during installation and operation.

This UPS is designed for industrial or commercial use. The UPS features a compact design that ts into a

limited-space working environment.

This product features the following:

• LCD display

• User-replaceable battery

• High reliability

• Auto restart during AC recovery

• AC overload protection

• Over temperature thermal protection

• Battery overcharge protection

• AVR (Auto Voltage Regulation)

• Input voltage out-of-range protection

• Remote monitoring and control software via UPSwatch

• Site wiring fault indicator

Page: 2

2.0 Important Safety Instructions

!WARNING - Risk of electric shock, fire and personal injury.

SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed

during installation and maintenance of the UPS and batteries.

The UPS is intended for installation in a controlled environment.

• Install the UPS in an indoor temperature- and humidity-controlled environment, free of

conductive contaminants.

• Do not install the UPS in or near water.

• In order to avoid overheating the UPS, allow proper ventilation of the unit. Do not block or cover the top,

bottom or sides of the UPS.

• Do not expose the UPS to direct sunlight or install the unit near any heat sources.

• Install the UPS onto a level surface in an upright position. Do not place the UPS on an unstable surface

such as a cart, stand or table.

• The UPS must be installed near the socket receptacle so that the cord can be easily disconnected.

To properly turn off the UPS, press the ON/OFF button for three (3) seconds, then disconnect the

input power supply cord from the AC power outlet.

• Connect the AC input power cord to a properly grounded AC supply source.

• Connect the UPS to a grounded supply circuit with proper branch circuit protection. Follow all applicable

National Electrical Codes®(NEC®) and Canadian Electrical Codes (CEC) as well as all local codes.

• This UPS is not for use in a computer room as dened in the Standard For the Fire Protection of

Information Technology Equipment, NFPA 75.

• Do not plug the UPS into a power strip. Do not daisy-chain one UPS power cord into another UPS

output receptacle.

• Do not place the UPS power cord where it may be damaged.

• Do not dispose of the UPS in a re as the battery may explode.

• Do not open or damage the battery. Released electrolyte is harmful to the skin and eyes and

may be toxic.

• Turn off the UPS and disconnect the input cord from the AC power supply before cleaning. Do not use

liquid or aerosol cleaners. Use only a dry cloth on the exterior of the UPS. Do not open the unit.

Page: 3

3.0 General Description

3.1 Front Panel

LCD

• The LCD will show functions of the UPS operation status.

ON/OFF Button

• To turn the UPS on, press the ON/OFF button for two (2) seconds and the LCD will display UPS status.

• To turn the UPS off, press the ON/OFF button for two (2) seconds and LCD display will shut off.

Setup Button

When you press the setup button, the LCD screen will display the functions below in the following sequence:

• Input Voltage (V)

• Input Frequency (Hz)

• Output Voltage (V)

• Output Frequency (Hz)

• Output Load (%)

• Output Load (kVA)

• Battery Voltage (%)

• Battery Voltage (V)

Page: 4

3.2 Rear Views

USB

Port

RJ 45

Surge

Input

Cable

Breaker

Site Fault

Indicator

Receptacles

Protection

Rear View of SSW700 and SSW1000

USB

Port

RJ 45

Surge

Input

Cable

Breaker

Site Fault

Indicator

Receptacles

Optional

SNMP

Protection

Rear View of SSW1500

Page: 5

4.0 System Block Diagrams

SSW700 and 1000 System Block Diagram

SSW1500 System Block Diagram

Page: 6

5.0 Installation and Operation

5.1 Installation Requirements

• Install the UPS in a controlled environment with adequate ventilation that is free of excessive dust

and high humidity.

• Avoid direct sunlight.

• Maintain a clearance of 4 inches (100 mm) between the UPS rear panel and the wall and 1 inch (25.4 mm)

between the UPS sides and the wall. Keep the air inlets unobstructed to facilitate ventilation and

heat dissipation.

5.2 Connect to Utility Power

Connect the power cord to the AC input power outlet.

5.3 Check the Site Wiring Fault Indicator

Check the site wiring fault indicator on the rear panel of the UPS. The light will be illuminated if the UPS

is plugged into an improperly wired AC power outlet. Detected wiring faults include ground and hot-neutral

polarity reversal.

5.4 Charge the Battery

The UPS charges its battery whenever it is connected to utility power, even when the unit is off. For best

results, charge the battery for eight (8) hours before initial use.

5.5 Turn On the UPS

Press the ON/OFF button for 2 seconds.

5.6 Set Up Audible Alarm On/Off

When the UPS powers on, the audible alarm may sound. The steps below outline how to turn the audible

alarm on or off.

• Step1: Press and hold the ON/OFF button for three (3) seconds to set up audible alarm ON/OFF

• Step2: Press the setup button once to set up audible alarm ON/OFF

• Step3: Press the ON/OFF button to exit

5.7 Connect the Loads

Connect the loads to the output receptacles on the rear panel of the UPS.

5.8 Connect Computer Interface

UPS monitoring software and an optional interface kit can be used with this UPS. If used, connect the interface

cable to the REMOTE PORT on the rear panel of the UPS and to the host computer (either COM 1 or COM 2).

5.9 Install the Optional SNMP Card (SSW1500 Models Only)

• Remove the Communication Port cover. Insert the SNMP card and secure with screws.

• Use network cables (supplied by user) to connect the UPS to the computer

network port.

• Please refer to the SNMP card operation website at www.SolaHD.com

for conguration settings and further instructions.

Page: 7

6.0 LCD Screen Diagnostics

Operation and Overview of LCD Panel

UPS Power On

To turn on the UPS unit, press the ON/OFF button

lightly for 2 seconds then the LCD will display on.

UPS Power Off

To turn off the UPS unit, press the ON/OFF button

lightly for 2 seconds then the LCD will display off.

AC Start Mode

AC start mode, the back light will ash once every

0.5 second.

Line and AVR Mode

AVR mode, the bottom icon will ash once every

0.5 second.

Page: 6

4.0 Interface

Operation and Overview of LCD Panel

Operation Mode

Status

Load and Battery capacity

Number will be displayed in the

following order Vin, Vo, load, battery

capacity

UPS Power On

To turn on the UPS unit, press the power switch SW2

lightly for 2 seconds then the LCD will display on.

UPS Power Off

To turn off the UPS unit, press the power switch SW2

lightly for 3 seconds then the LCD will display off.

AC Start Mode

ACstartmode,thebacklightwillashonceevery

0.5second

Line and AVR Mode

AVRmode,thebottomiconwillflashonce

every0.5second.

Battery Mode Low Battery

Batteryvoltagelow,thebatteryalarmiconwillash

onceevery0.5second.

SSW UPS

Rev.3 2019/05/30

Page: 8

Battery Mode Low Battery

Battery voltage low, the battery alarm icon will

ash once every 0.5 second.

Battery Sleep Mode

Battery voltage UVP, the battery stops to provide

power, and the battery alarm icon will ash once

every 0.5 second.

Battery Voltage Over Charge

Battery voltage over charge, the battery alarm icon

will ash once every 0.5 second and display HI.

Short for Line and AVR Mode

LCD display SP, when UPS operates in LINE or

AVR mode.

Short for Battery Mode

LCD display SP, when UPS operates in

battery mode.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Emerson UPS

Emerson

Emerson 1000VA Manuale utente

Emerson

Emerson Liebert GXT3 6000VA RTL630 Manuale utente

Emerson

Emerson Liebert itON BX Manuale utente

Emerson

Emerson Liebert GXT-MT Manuale utente

Emerson

Emerson itON BX Manuale utente

Emerson

Emerson Liebert PowerSure PSP Manuale utente

Emerson

Emerson Series 610 Manuale utente

Emerson

Emerson NXr Manuale utente

Emerson

Emerson Liebert GXT2-10KIPPCBL Manuale utente

Emerson

Emerson Liebert NXL Manuale utente

Emerson

Emerson SOLAHD S4KC Series Manuale utente

Emerson

Emerson SolaHD S4K2UC Series Manuale utente

Emerson

Emerson Liebert NXL 250-400kVA Manuale utente

Emerson

Emerson Liebert GXT MT+LB 10KL Manuale utente

Emerson

Emerson Liebert APM 90 Manuale utente

Emerson

Emerson Liebert GXT4-6000RT230 Manuale utente

Emerson

Emerson Liebert HiPulse E Series Manuale per l'uso e la cura

Emerson

Emerson Liebert GXT4 Manuale utente

Emerson

Emerson Liebert NXC 10-20kVA Manuale di istruzioni

Emerson

Emerson Liebert GXT3-5000RT230 Manuale utente

Emerson

Emerson Liebert GXT3 Series Manuale utente

Emerson

Emerson Liebert GXT3 Series Manuale utente

Emerson

Emerson Liebert PSA Manuale utente

Emerson

Emerson Liebert NX Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente

ZincFive

ZincFive BC Series Manuale utente