Emulex LP8000 Manuale di installazione e funzionamento
LP8000 Installation and Reference Manual
Table of Contents
Installation
Compatability
Prerequisites
Set Jumpers
Install HBA
Change GBIC
Attach Media
Apply Power
View LEDs
Reference
Specifications
DB9 Pinout
FCC and Regulatory Notices
Declaration of
Conformity
Laser Safety
Emulex Drivers, Software and Manuals
1
Chapter 1 − Installation
Table of Contents
Compatability
Prerequisites
Set Jumpers
Install HBA
Change GBIC
Attach Media
Apply Power
View LEDs
Emulex Drivers, Software and Manuals
2
Installation
Caution Emulex LightPulse Host Bus Adapters (HBAs) contain
electronic components that can be damaged by static
electricity through an electrostatic discharge (ESD) event. To
prevent ESD damage, maintain frequent contact with any
grounded metal surface. A grounding wrist strap is useful for
this purpose. Handle the card carefully at all times and
preferably by the edges. Avoid touching electronic
components and keep the card in the original packaging until
you are ready for installation.
Compatibility
Software
Environments Windows Server 2003, Windows 2000, Windows NT,
NetWare, HP-UX, Linux, Solaris, AIX
Hardware
Environments PCI hardware platforms: x86, SPARC and PowerPC
Prerequisites
One open 32−bit or 64−bit (recommended) PCI bus slot with a 3.3 VDC
or 5.0 VDC signaling interface
•
Maximum PCI bus clock rate of 33 MHz• Media and connectors (user supplied)• Multimode fiber optic cable (50/125 µ m or 62.5/125 µ m) with
dual SC connectors, used with short wave lasers
♦
Single mode fiber optic cable (9/125 µ m) with dual SC
connectors, used with long wave lasers
♦
Copper duplex cabling with DB9 connectors (also called DE9)♦
Emulex Drivers, Software and Manuals
3
Set Jumpers
The host adapter has two jumper blocks (JX1, JX2) that control the host adapter's
device ID. The default Device ID is F800.
Device ID Jumper Setting
F800 JX1:1−2, JX2:2−3
F801 JX1:2−3, JX2:1−2
1AE5 JX1:2−3, JX2:2−3
Emulex Drivers, Software and Manuals
4
Install Host Bus Adapter Board
Record IEEE address and serial number.
Each host adapter is shipped with a unique address identifier called the
IEEE address. The Fibre Channel industry uses a World Wide Name
(WWN) derived from the IEEE address, and this number is need for
arbitrated loop connectivity. The serial number is used when
communicating with Emulex. Both numbers are clearly marked on the
board. We recommend that you record these numbers before installation.
1.
Turn off and unplug the computer.2. Remove the computer case.3. Remove the blank panel from an empty 32− or 64−bit PCI bus slot.4. Insert host adapter board into the empty 32− or 64−bit PCI bus slot.
Press firmly until the board is seated.
5.
Secure the host adapter's mounting bracket to the case with the panel
screw.
6.
Replace the computer case and tighten case screws.7.
The host adapter is now installed in the PC and is ready for media attachment.
Emulex Drivers, Software and Manuals
5
Change the GBIC Connector
A GBIC, or Gigabit Interface Converter, is a connector that offers a flexible
choice of copper or fiber optic media. A GBIC supports either short wave or long
wave optical transmission. These types are available:
Short−wave fiber optic GBIC with dual SC connectors• Long−wave fiber optic GBIC with dual SC connectors• Copper GBIC with DB9 connector•
Caution An Emulex supplied GBIC is required to maintain regulatory
compliance with worldwide certifications (for example, FCC,
C−Tick, CE, and so on).
A GBIC should be matched with its cabling to obtain optimum performance and
distance. For example, a short wave fiber optic GBIC best supports either
62.5/125 or 50/125 multimode cable, while a long wave fiber optic GBIC
functions best with 9/125 single mode cable.
To change a GBIC:
Exert slight pressure on the tabs.1. Gently pull out the GBIC as shown.2. Slide in a new GBIC, pressing firmly to seat the GBIC into the board.3.
Emulex Drivers, Software and Manuals
6
Attach Media
Attach fibre optic or copper cable to the host bus adapter.
Attach Fiber Optic Cable (Multi/Single Mode)
Note The host adapter will not allow normal data transmission on
an optical link unless it is connected to another similar or
compatible laser product (that is, multimode to multimode.)
Use fiber optic cable supporting a data rate of 1.0625 Gb/s for short−wave and
long−wave lasers, that adheres to the following specifications:
Fiber Optic Cable Maximum
Length Minimum
Length Connector
62.5/125 µm
(multimode) 175 meters 2 meters Dual SC
50/125 µm (multimode) 500 meters 2 meters Dual SC
9/125 µm (single mode) 10,000 meters 2 meters Dual SC
Connect the fiber optic cable to the dual SC connector on the host
adapter board as shown.
1.
Connect the other end of the cable to the Fibre Channel device.2.
After the media is connected to the host adapter, you are ready to apply power to
the computer.
Emulex Drivers, Software and Manuals
7
Attach Copper Duuplex Cable
Use copper Twinax or Quad Axial cable that adheres to the following
secifications:
Cable Type Maximum Length Data Rate Connector
Twinax or Quad Axial 30 meters 1.0625 Gb/s DB9
Connect the copper duplex cable to the DB9 connector on the host
adapter board as shown.
1.
Connect the other end of the cable to the Fibre Channel device.2.
After the media is connected to the host adapter, you are ready to apply power to
the computer.
Emulex Drivers, Software and Manuals
8
Apply Power
Verify that the host adapter is securely installed in the computer.1. Verify that correct media is attached.2. Plug in and turn on the computer.3. Observe LEDs for Power On Self Test (POST) results.4.
View LEDs
Green and yellow display lights (LEDs) can be seen through openings in the host
adapter's mounting bracket. Green indicates power and yellow signifies port
activity. A third LED is present on LP8000 models with embedded optical
interfaces, and indicates that light is being received by the port.
POST conditions and results are summarized in this table.
Green
LED Yellow
LED State
OFF OFF Wake−up failure (dead board)
OFF ON POST failure (dead board)
OFF Slow blink (1 Hz) Wake−up failure (dead board)
OFF Fast blink (4 Hz) Failure in POST (dead board)
OFF Flashing (irregular) POST processing in progress
ON OFF Failure while functioning
ON ON Failure while functioning
ON Slow blink (1 Hz) Normal − link up
ON Fast blink (4 Hz) Normal − Updating firmware or driver initializing
Blink OFF Normal − link down or not yet started
Emulex Drivers, Software and Manuals
9
Chapter 2 − Reference
Table of Contents
Specifications
DB9 Pinout
FCC and Regulatory Notices
Declaration of Conformity
Laser Safety
Emulex Drivers, Software and Manuals
11
Indice
Altri manuali Emulex Scheda PCI
