ENCRAJE LC-1700 Manuale utente
Directory
13
15
16
17
01
02
03
06
07
10
Foreword
LC-1700 is developed and researched as high-end automatic
laminating machine.
This produce mainly work for normal cold laminating,low-temperature
and vertival cutting.
Simple operation,intelligent and convenient,multi-purpose use.
To work with LC-1700 better,please read manual carefully to ensure
operation correctly.
Note: All described functions and instructions please subject to actual
equipment.
1
2
LC-1700 Automatic Laminator User Manual
Max width
Max lift height
Max speed
Roller diamater
Master-control Interface
Pedal switch mode
Max film diameter
Max media diamter
Max take-up dismater
Infinte variable speed
Metering
Auto-stop at media finished
Curve Start-stop
Auto-cutting
Anti-pinch device
Temperature control range
Heating way
Preheating time
Lifting way
Motor type
Reducer
Drive mode
Motor power
Heating input power
Rated input voltage
Net/Gross Weight
Equipment size
Package size
1630mm
40mm
38m/min
130mm
Industrial Handle
Curve Start-stop
250mm
360mm
380mm
Yes
Yes
Yes
Yes
Yes
Yes
Room temperature to 80℃
Infrared heating
10-20min
Electrical
Brushless DC servo motor
Planet-gear speed reducer
By chain
350W
1800W
110/220V
282kg/372kg
2050mm*560mm*1480mm
2200mm*700mm*1560mm
3
LC-1700 Automatic Laminator User Manual
Safety Cautions:
1.Please check package box before unpack to avoid any damage
to machine during delivery.
2.Please check all items according to packing list.
or explosive goods,and please not place equipment in the vent,
quality.
4.Equipment’s tundle only available for short-distance move.
5.This equipment work with single-phase 110/220V AC voltage.
please ensure the power supply reach to the standard and big
enough capacity before power on machine.There shall be primary
single-phase 110/220V,20A circuit breaker with over-current protection
and well0groundedto avoid any personal injury.Three-core power
outlet that available to grounding is required.
6.Please protect front work platform from heavy load to avoid any
damage to the platform or the positioning screw.
7.When using a forklift to move equipment,please put cardboard or
veneer on the forklift arm to avoid any damage to it.When forklift
arms under equipment tray,personnel are required at equipment both
sides to avoid equipment topple over back/forwards
4
LC-1700 Automatic Laminator User Manual
Preparation:
1.Move machine host body to work environment;
waming: In carry or movement,acting point shall be the left & right shell,
or tray bottom,carrying guide shaft,work platform,damper or cover is not
available.
2.Turn the rubber by hand to take out the foam between upper & lower
rollers.
3.Install control handle
Take out the control handle form accessory box:
Insert the handle’s aeriel plug to equipment’s corresponding port(see
Platform
Roller
Tray
Guide shaft
Shell
Cover
Damper
5
LC-1700 Automatic Laminator User Manual
Handle-core Aeriel socket
Socket port for the handle aeriel plug as above picture.
There is magnetic stell back on handle.You will can attach it to any part of
machine as need.
4.Foot switch
As shown below
Start and stop and
rubber roller lifting Intelligent speed
control
Control handle
As shown on the right
The back of the handle has its own
magnetic steel, and the user can
place the handle on the handle of
the case according to his needs.
6
LC-1700 Automatic Laminator User Manual
Emergency stop switchEmergency stop switch
Handle
Lift button
Switch
Paper out parking
Glue roll
Infrared anti-pinch
Front platform
Dual control intelligent foot switch
Lift button
Film roll
Guide shaft
Trim knob
Cutter
Rear flip platform
Laminated shaft
Closing paper shaft
Scroll
Damper
Reel
7
LC-1700 Automatic Laminator User Manual
1.preset temperature
3.Actual temperature
5.Actual speed
7.Add
9.Function
11.Start and stop key
13.Heat/Cold
15.Metering
2.Heating state
4.Roller’s forward & reverse state
6.roller’s lifting state
8.Lift button for roller
10.Decrease button
12.Forward/Reverse button
14.Set speed
8
LC-1700 Automatic Laminator User Manual
Functions Instruction:
1.Handle Start
and show handle version unmber at“metering”position.
2.Start/Stop
In machine stop state,press key will make it start and
In run state,press key and machine speed will reauce
When machine give an alarm,press key to disarm the
state.
4.Direction Switch
Direction switch only can be realized in stop state.Each time
The “Forward/Reverse”arrow in display shows the present
Switch button not work in machine run state.
Indice
