ENDA ETM1411 Manuale utente

SETSET

ETM1411

ENDA DIGITAL TIMER

STOP

START

OUT MIN

HOUR

TECHNICAL SPECIFICATIONS

Supply 230V AC +10 -20 , 50/60Hz or 24% % V AC/DC 10%, 50/60Hz or 12V AC/DC 10%, 50/60Hz± ±

Power consumption Max 4VA

2.5mm² screw-terminal connections

±1%

4 digits, 12.5mm, 7 segment yellow LED

Wiring

Scale

Sensitivity

Time Accuracy

Indicator

EMC

Safety requirements

EN 61326-1: 1997, A1: 1998, A2: 2001 (Performance criterion B is satisfied for EMC tests.

The device is designed to operate in controlled electromagnetic environment)

EN 61010-1: 2001 ( )pollution degree 2, overvoltage category II

START INPUT

Input type Control with mechanical contact.

Min. = 100ms

On and Off times for input

pulses

OUTPUT

ELEKTRÝKSEL ÖZELLÝKLER

OUT Relay: 250V AC, 8A ( ), NO+NCfor resistive load

Mechanical 30.000.000 operation; Electrical 100.000 operation

Life expectancy for relay

ENVIRONMENTAL CONDITIONS

Height 2000mMax.

80% up to 31°C decreasing linearly 50% at 40°C.

Ambient/storage temperature

Max. Relative humidity

0 ... +50°C/-25 ... +70°C (with no icing)

Selectable 99:59 min. or hour.

1 sec.

Rated pollution degree According to EN 60529 Front panel : IP65

Rear panel : IP20

Do not use the device in locations subject to corrosive and flammable gases.

HOUSING

Housing type Suitable for flush-panel mounting

Dimensions W77xH35xD71mm

Weight Approx. 198g (after packing)

Enclosure material Self extinguishing plastics

Thank you for choosing ENDA ETM1411 digital timer.

* 35x 77mm sized.

* Single contact output for timing control.

* External start input.

* Display can be adjusted to show min. or sec.

* Scale ;

0:01 .... 99:59 mins.

0:01 .... 99:59 hrs.

* Decrease and increace step of time can be adjusted.

* Start and stop possibility by front panel.

* 16 different warning tones.

* Upper and lower limits of the setpoint can be

adjusted.

* CE marked according to European Norms.

Connection Diagram

ENDA ETM1411 is intended for installation in control panels. Make sure that the device is

used only for intended purpose. The shielding must be grounded on the instrument side.

During an installation, all of the cables that are connected to the device must be free of

electrical power. The device must be protected against inadmissible humidity, vibrations,

severe soiling and make sure that the operation temperature is not exceeded. All input and

output lines that are not connected to the supply network must be laid out as shielded and

twisted cables. These cables should not be close to the power cables or components. The

installation and electrical connections must be carried out by a qualified staff and must be

according to the relevant locally applicable regulations.

1/2

SÝSEL MÜHENDÝSLÝK ELEKTRONÝK SAN. VE TÝC. A.Þ.

Yukarý Dudullu Barbaros Cad. Kutup Sok. No:20 34775 - ÜMRANÝYE/ÝSTANBUL/TÜRKÝYE

Tel : +90 216 499 46 64 Pbx. Fax : +90 216 365 74 01

url : www.enda.com.tr ETM1411-E-05-R

Holding screw

0.4-0.5Nm

Equipment is protected throughout

by DOUBLE INSULATION.

While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.

SUPPLY:

NOTE :

184-253V AC

50/60Hz 4VA

Line

Neutral

230V AC

Supply

Switch

Note:

Cable size: 1,5mm²

Fuse

F 100 mA

250V AC

Fuse should

be connected.

IEC 60227 or IEC 60245.

2) In accordance with the safety regulations, the power

supply switch shall bring the identification of

the relevant instrument and it should be easily accessible

by the operator.

Mains supply cords shall meet the requirements of

ENDA ETM1411 DIGITAL TIMER

Please read this document carefully before using this product. Theguarantee will be

invalidated if the device is damaged by not following instructions detailed in the

manual. Thecompany shall not be responsible for any damageor losses however

caused, whichmay be experienced as a result ofthe installation or use of this product.

Order Code : ETM1411-     

1Supply Voltage

230VAC...230V AC

24............24V AC/DC

12............12V AC/DC

24V AC/DC 10%

50/60Hz 4VA

SN: XXXXXXXXX

ETM1411-24

DIGITAL TIMER

ENDA INDUSTRIAL ELECTRONICS

OUT

250V AC 8A

RESISTIVE LOAD

1 2 3 4 5 6 7 8 9 10 11 12

START

SN: XXXXXXXXX

ETM1411-230VAC

DIGITAL TIMER

ENDA INDUSTRIAL ELECTRONICS

230V AC +10% -20%

50/60Hz 4VA

OUT

250V AC 8A

RESISTIVE LOAD

1 2 3 4 5 6 7 8 9 10 11 12

START

12V AC/DC 10%

50/60Hz 4VA

SN: XXXXXXXXX

ETM1411-12

DIGITAL TIMER

ENDA INDUSTRIAL ELECTRONICS

OUT

250V AC 8A

RESISTIVE LOAD

1 2 3 4 5 6 7 8 9 10 11 12

START

Panel cut-out

Dimensions

Note :

1) Panel thickness

should be maximum

7 mm.

2) If there is no 60mm

free space at the back

side of the device, it

would be difficult to

remove it from the

Panel.

71mm

29mm

Flush mounting

clamp

For removing mounting clamps:

Push the flush-mounting

clamp in direction 1as shown

in the figure below. Then, pull

out the clamp in direction 2.

35mm

77mm

SETSET

ETM1411

ENDA DIGITAL TIMER

STOP

START

OUT MIN

HOUR

SN: XXXXXXXXX

ETM1411-230VAC

DIGITAL TIMER

ENDA INDUSTRIAL ELECTRONICS

230V AC +10% -20%

50/60Hz 4VA

OUT

250V AC 8A

RESISTIVE LOAD

1 2 3 4 5 6 7 8 9 10 11 12

START

Flush mounting

clamp

Depth

Panel

71mm 5mm

Rubber

packing

The lower limit

of the setpoint.

Adjustable between

0.01 and T.uPl.

The upper limit

of the setpoint.

Adjustable between

T.lol and 99.59.

Selection of start type.

By external start input and

start/stop keys, timer can be run

and stopped. 4 different selection

types are defined in the

control diagram.

Selection of relay output.

If typ.0 is selected, timer runs

by start and relay contact shuts.

When time is over, relay contact

opens. If typ.1 is selected, timer

runs by start. When time is over,

relay contact shuts.

Selection of buzzer sound.

Adjustable 16 different sounds.

If this parameter is selected 0,

warning tone is canceled.

Selection of time unit.

If min is selected, time can be

adjutable max. 99:59 min.

If Hour is selected, time can be

adjutable max. 99:59 h.

Increase or decrease

step of the setpoint.

Adjustable between

1 and 30.

When pressed key, TIMER set value flashes and by using and keys the value can be adjusted

with the step defined byIn.de.

Programming Mode

Run Mode

Time

value

T.lol

T.uPl Str.t.

Str.t.

In.de Out.t.

Sond.

Out.t.

TYP.0

TYP.1

TYP.2

TYP.3

1000

ETM1411-E-05-R

If key is pressed and held for 3 seconds,

programming mode is entered.

30 59

60 00

59 59

60 00

SET

T.bas S.Cod. Access code for entering

security menu.

This parameter should be 411.

Access code for

timer configuration menu.

A.-t.S.

A.-T.c.

Access code for timer set menu

If key is pressed,

run mode is entered.

T.S. T.c. SE

Used for adjusting the value of the setpoint in the run mode and for adjusting the selected parameter in the programming mode. For adjusting the selected parameter, while holding key, the value can be

adjusted by using and keys.

When held down for one second in the run mode, timer runs.

run mode. When held down for a few seconds, the change rate accelerates.

Used for selecting menu and increasing setpoint value of the parameters in the programming mode and for increasing the setpoint value in the

When held down for one second in the run mode, timer and voiced warning are stopped.(When Str.t. = TYP.1 mode is selected, timer and voiced warning can be stopped if external start input is off). Used

for selecting parameters and decreasing the setpoint value in the programming mode and for decreasing the setpoint value in the run mode. When held down for a few seconds, the change rate accelerates.

INDICATOR OF

SELECTING

HOUR

INDICATOR OF

SELECTING

MINUTE

INDICATOR OF

CONTACT OUTPUT