Endress+Hauser Proline Promag H Specifiche tecniche

Products Solutions Services

Brief Operating Instructions

Proline Promag H

Electromagnetic sensor

These instructions are Brief Operating Instructions; they are

not a substitute for the Operating Instructions pertaining to

the device.

Brief Operating Instructions part 1 of 2: Sensor

Contain information about the sensor.

Brief Operating Instructions part 2 of 2: Transmitter

→  3.

KA01289D/06/EN/02.21

71508647

2021-07-01

Proline Promag H

2 Endress+Hauser

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

Proline Promag H Brief Operating Instructions for flowmeter

Endress+Hauser 3

Brief Operating Instructions for flowmeter

The device consists of a transmitter and a sensor.

The process of commissioning these two components is described in two separate manuals

that together form the Brief Operating Instructions for the flowmeter:

• Brief Operating Instructions Part 1: Sensor

• Brief Operating Instructions Part 2: Transmitter

Please refer to both parts of the Brief Operating Instructions when commissioning the device,

as the contents of the manuals complement one another:

Brief Operating Instructions Part 1: Sensor

The Sensor Brief Operating Instructions are aimed at specialists with responsibility for

installing the measuring device.

• Incoming acceptance and product identification

• Storage and transport

• Installation

Brief Operating Instructions Part 2: Transmitter

The Transmitter Brief Operating Instructions are aimed at specialists with responsibility for

commissioning, configuring and parameterizing the measuring device (until the first

measured value).

• Product description

• Installation

• Electrical connection

• Operation options

• System integration

• Commissioning

• Diagnostic information

Additional device documentation

These Brief Operating Instructions are the Brief Operating Instructionspart 1: Sensor.

The "Brief Operating Instructions part 2: Transmitter" are available via:

• Internet: www.endress.com/deviceviewer

• Smart phone/tablet: Endress+Hauser Operations App

Detailed information about the device can be found in the Operating Instructions and the

other documentation:

• Internet: www.endress.com/deviceviewer

• Smart phone/tablet: Endress+Hauser Operations App

Table of contents Proline Promag H

4 Endress+Hauser

Table of contents

1 About this document .............................................................. 5

1.1 Symbols used ......................................................................... 5

2 Basic safety instructions .......................................................... 7

2.1 Requirements for the personnel ............................................................ 7

2.2 Designated use ........................................................................ 7

2.3 Workplace safety ...................................................................... 8

2.4 Operational safety ......................................................................8

2.5 Product safety ......................................................................... 8

2.6 IT security ............................................................................ 9

3 Incoming acceptance and product identification ................................. 10

3.1 Incoming acceptance ................................................................... 10

3.2 Product identification .................................................................. 11

4 Storage and transport ........................................................... 12

4.1 Storage conditions .................................................................... 12

4.2 Transporting the product ................................................................12

5 Installation ...................................................................... 14

5.1 Installation conditions .................................................................. 14

5.2 Mounting the measuring device ...........................................................18

5.3 Post-installation check ................................................................. 23

6 Disposal ......................................................................... 24

6.1 Removing the measuring device .......................................................... 24

6.2 Disposing of the measuring device ......................................................... 24

Proline Promag H About this document

Endress+Hauser 5

1 About this document

1.1 Symbols used

1.1.1 Safety symbols

DANGER

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

1.1.2 Symbols for certain types of information

Symbol Meaning Symbol Meaning

Permitted

Procedures, processes or actions that

are permitted.

Preferred

Procedures, processes or actions that

are preferred.

Forbidden

Procedures, processes or actions that

are forbidden.

Tip

Indicates additional information.

Reference to documentation

Reference to page

Reference to graphic

… Series of steps

Result of a step Visual inspection

1.1.3 Electrical symbols

Symbol Meaning Symbol Meaning

Direct current Alternating current

Direct current and alternating current Ground connection

A grounded terminal which, as far as

the operator is concerned, is grounded

via a grounding system.

About this document Proline Promag H

6 Endress+Hauser

Symbol Meaning

Protective Earth (PE)

A terminal which must be connected to ground prior to establishing any other connections.

The ground terminals are situated inside and outside the device:

• Inner ground terminal: Connects the protectiv earth to the mains supply.

• Outer ground terminal: Connects the device to the plant grounding system.

1.1.4 Tool symbols

Symbol Meaning Symbol Meaning

Torx screwdriver Flat blade screwdriver

Cross-head screwdriver Allen key

Open-ended wrench

1.1.5 Symbols in graphics

Symbol Meaning Symbol Meaning

1, 2, 3,... Item numbers

… Series of steps

A, B, C, ... Views A-A, B-B, C-C, ... Sections

Hazardous area

Safe area (non-hazardous area)

Flow direction

Proline Promag H Basic safety instructions

Endress+Hauser 7

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel must fulfill the following requirements for its tasks:

‣Trained, qualified specialists must have a relevant qualification for this specific function

and task.

‣Are authorized by the plant owner/operator.

‣Are familiar with federal/national regulations.

‣Before starting work, read and understand the instructions in the manual and

supplementary documentation as well as the certificates (depending on the application).

‣Follow instructions and comply with basic conditions.

2.2 Designated use

Application and media

The measuring device is intended only for the flow measurement of liquids with a minimum

conductivity of 5 μS/cm(Promag 10, 100, 300, 500) or 20 μS/cm (Promag 200).

Depending on the version ordered, the measuring device can also measure potentially

explosive, flammable, poisonous and oxidizing media.

Measuring devices for use in hazardous areas, in hygienic applications or where there is an

increased risk due to process pressure, are labeled accordingly on the nameplate.

To ensure that the measuring device remains in proper condition for the operation time:

‣Keep within the specified pressure and temperature range.

‣Only use the measuring device in full compliance with the data on the nameplate and the

general conditions listed in the Operating Instructions and supplementary documentation.

‣Based on the nameplate, check whether the ordered device is permitted for the intended

use in the hazardous area (e.g. explosion protection, pressure vessel safety).

‣Use the measuring device only for media to which the process-wetted materials are

sufficiently resistant.

‣If the ambient temperature of the measuring device is outside the atmospheric

temperature, it is absolutely essential to comply with the relevant basic conditions as

specified in the device documentation.

‣Protect the measuring device permanently against corrosion from environmental

influences.

Incorrect use

Non-designated use can compromise safety. The manufacturer is not liable for damage caused

by improper or non-designated use.

LWARNING

Danger of breakage due to corrosive or abrasive fluids and ambient conditions!

‣Verify the compatibility of the process fluid with the sensor material.

‣Ensure the resistance of all fluid-wetted materials in the process.

‣Keep within the specified pressure and temperature range.

Basic safety instructions Proline Promag H

8 Endress+Hauser

NOTICE

Verification for borderline cases:

‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in

verifying the corrosion resistance of fluid-wetted materials, but does not accept any

warranty or liability as minute changes in the temperature, concentration or level of

contamination in the process can alter the corrosion resistance properties.

Residual risks

LWARNING

The electronics and the medium may cause the surfaces to heat up or freeze. This

presents a burn hazard!

‣For elevated or low fluid temperatures, ensure protection against contact.

2.3 Workplace safety

For work on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

For welding work on the piping:

‣Do not ground the welding unit via the measuring device.

If working on and with the device with wet hands:

‣Due to the increased risk of electric shock, gloves must be worn.

2.4 Operational safety

Risk of injury!

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for interference-free operation of the device.

Ambient requirements for transmitter housing made of plastic

If a plastic transmitter housing is permanently exposed to certain steam and air mixtures, this

can damage the housing.

‣If you are unsure, please contact your Endress+Hauser Sales Center for clarification.

‣If used in an approval-related area, observe the information on the nameplate.

2.5 Product safety

This measuring device is designed in accordance with good engineering practice to meet state-

of-the-art safety requirements, has been tested, and left the factory in a condition in which it

is safe to operate.

It meets general safety standards and legal requirements. It also complies with the EU

directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser confirms

this by affixing the CE mark to the device.

Proline Promag H Basic safety instructions

Endress+Hauser 9

2.6 IT security

Our warranty is valid only if the device is installed and used as described in the Operating

Instructions. The device is equipped with security mechanisms to protect it against any

inadvertent changes to the settings.

IT security measures, which provide additional protection for the device and associated data

transfer, must be implemented by the operators themselves in line with their security

standards.

Incoming acceptance and product identification Proline Promag H

10 Endress+Hauser

3 Incoming acceptance and product identification

3.1 Incoming acceptance

Are the order codes on

the delivery note (1)

and the product sticker

(2) identical?

Are the goods

undamaged?

Order code:

Ser. no.:

Ext. ord. cd.:

Date:

Do the nameplate data

match the ordering

information on the

delivery note?

Is the envelope present

with accompanying

documents?

• If one of the conditions is not satisfied, contact your Endress+Hauser Sales Center.

• The Technical Documentation is available via the Internet or via the Endress+Hauser

Operations App.

Indice

Altri manuali Endress+Hauser Accessori

Endress+Hauser

Endress+Hauser Prosonic S Series Manuale

Endress+Hauser

Endress+Hauser Proline 800 Specifiche tecniche

Endress+Hauser

Endress+Hauser OUSAF46 Manuale utente

Endress+Hauser

Endress+Hauser Proline 200 FOUNDATION Fieldbus Specifiche tecniche

Endress+Hauser

Endress+Hauser Turbimax CUS51D Manuale utente

Endress+Hauser

Endress+Hauser CLS15D Manuale utente

Endress+Hauser

Endress+Hauser Deltapilot M FMB50 Specifiche tecniche

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale utente

Endress+Hauser

Endress+Hauser Dipfit W CLA111 Manuale utente

Endress+Hauser

Endress+Hauser Oxymax COS22 Series Manuale utente

Endress+Hauser

Endress+Hauser Viomax CAS51D Manuale utente

Endress+Hauser

Endress+Hauser ISEmax CAS40D Manuale utente

Endress+Hauser

Endress+Hauser Oxymax H COS21D Manuale utente

Endress+Hauser

Endress+Hauser Deltapilot S DB50 Manuale

Endress+Hauser

Endress+Hauser Condumax CLS15 Manuale utente

Endress+Hauser

Endress+Hauser Deltapilot S FMB70 Istruzioni per l'installazione

Endress+Hauser

Endress+Hauser Deltabar S PMD70 Manuale utente

Endress+Hauser

Endress+Hauser OUSAF44 Manuale utente

Endress+Hauser

Endress+Hauser Oxymax W COS71 Manuale

Endress+Hauser

Endress+Hauser Oxymax COS61 Manuale

Endress+Hauser

Endress+Hauser Memosens COS81D Manuale utente

Endress+Hauser

Endress+Hauser Turbimax W CUS31 Manuale utente

Endress+Hauser

Endress+Hauser Micropilot M FMR230 Manuale utente

Endress+Hauser

Endress+Hauser Memosens COS81E Specifiche tecniche

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente