Ener-G+ HIB-2000 Manuale utente
1
year/an
warranty
garantie
Modèle/Model: HIB-2000
BATHROOM WALL-MOUNTED FAN
HEATER
Operators’ Manual p. 1
AÉROCONVECTEUR MURAL POUR
SALLE DE BAINS
Guide de l'utilisateur p. 11
...................................................2
.....................................................................................3
.............................................................4
.................................................................5
.............................................................................................6
.................................................................8
..............................................................................................9
............................................................................................10
.........................................................................11
• IMPORTANT SAFETY INSTRUCTIONS
• SPECIFICATIONS
• INSTALLATION INSTRUCTIONS
• ELECTRICAL CONNECTIONS
• OPERATION
• MAINTENANCE & CLEANING
• WARRANTY
• PARTS LIST
• SCHEMATIC DRAWING
1
2
IMPORTANT SAFETY INSTRUCTIONS
• Read all instructions before using this fan heater. SAVE THESE INSTRUCTIONS!
• In Canada, the installation of this product must be carried out by a certified master
electrician.
Before installing and operating this product, the owner and/or installer must read,
understand and follow these instructions and keep them handy for future reference. If
these instructions are not respected, the warranty will be considered null & void and
the manufacturer deems no further responsibility for this product.
1.This product may present a risk of fire if it is not properly installed & maintained as
per the instruction manual.
2.Not following these instructions could lead to serious injury causing bodily harm,
property damage, and electrocutions resulting in death.
3.This product must be installed by a certified master electrician, in accordance with
all local & national building codes.
4.It is the user’s responsibility to assure that materials such as blankets, towels, beds,
furniture, laundry baskets, clothing, etc. do not come in contact with, nor come
within 4 inches (10 centimetres) of the heater. Failure to follow this warning could
lead to fire.
5.Never obstruct the airflow locations, i.e, air intake and exhaust. This could cause the
product to overheat and lead to fire.
6.Certain locations are dustier than others. It is therefore the user’s responsibility to
determine whether or not the product must be cleaned based on dirt build-up on the
unit’s air intake & exhaust, as well as inside the unit. Accumulated dust and dirt
could cause components to become defective, which could lead to fire.
7.If the installer and/or user modifies this product in any way, he/she will be held
responsible for any damages resulting from this modification.
8.Make sure that the heating capacity of the unit is sufficient for the size of room it is
intended to heat. If the capacity is insufficient, the heater will work constantly,
causing it to discolour (turn yellow) and/or prematurely deteriorate.
Suggested calculation to determine heating requirements :
10 watts / square foot (0.3 m2) based on a ceiling height of 8 feet (2.44 meters).
1.2 watts / cubic foot (0.3 m3) for locations where the ceiling height exceeds 8 feet
(2.44 meters).
9.An activated thermal protection (overheat sensor) warns that the heater has been
subjected to abnormal conditions. If this occurs, stop using the heater immediately
and bring it to an authorized service centre for inspection and repair.
3
IMPORTANT SAFETY INSTRUCTIONS
10.A heater contains components that become hot and produce electrical sparks. Do
not operate it in areas where gasoline, paint, or flammable liquids are used or
stored.
11.This unit must be permanently secured to one of the bathroom walls and must only
be used to heat the room where it is installed.
12.Make sure the main power supply complies with the rating plate: 240 V AC, 60 Hz.
13.Never let children play with the unit. Caution! When the unit is on, the air outlet grille
can reach very high temperatures (more than 80 °C).
14.Never use this unit within arm’s reach while in the shower, the bathtub or near a
sink. Never let water enter the bathroom fan heater which will lead to electric shock!
15.Never secure the unit to walls made of synthetic materials.
16.This heater must always be installed vertically on a wall.
SPECIFICATIONS
240V AC, 60Hz
8.14 lbs (3.7 kg)
13.78” x 22.6” x 6.7”
(35 x 57.5 x17 cm)
This fan heater is intended for permanent wall-mounting with the provided screws.
The heater has a thermal cut-off protection. If the thermal cut-off protection trips, switch
off the power. The unit should reset automatically after 10 minutes. If the thermal cut-off
protection trips again, determine the reason for overheating.
Model HIB-2000
Voltage
Watts
Amps
1 200/2 000 W
8.3 Amp
Net Weight
Dimensions
(W x H x D)
INSTALLATION INSTRUCTIONS
4
4. Insert the two top screws provided,leaving a gap of 1/4" (6mm) between the screw
head and the wall.(Fig.5)
5. Hang the unit on the installed screws, while holding it securely in your hands.
WALL MOUNTING
1. The unit must be secured to the wall 24in (600mm) away from the floor and 12 in
(305mm) from adjacent walls (Fig.2). The unit can't be covered or hidden by a door.
2. Drill three holes with a diameter slightly smaller than the one for the plastic pins
provided.
3. Insert the pins.(Fig.3 and Fig.4)
TOOLS REQUIRED (not included)
• Electric drill
• Phillips (cross-head) screwdriver
• Measuring tape
To fix the towel rack (Fig.1)
1.Place both ends of the towel rack into the slots at
the back of unit and align the holes.
2.Screw the towel rack and unit together with four
screws (supplied).
Fig.2
Fig.1
Fig.3 Fig.4
Minimum
12” (305mm)
Minimum
12” (305mm)
Minimum
24” (600mm)
6” (153mm)
15 3/8” (319mm)
15 3/8” (319mm)
6” (153mm)
Wall Wall
Floor
• Installation must be performed in accordance with the requirements of the CEC by
authorized personnel only.
5
ELECTRICAL CONNECTIONS
INSTALLATION INSTRUCTIONS
Fig.8
• Make the electrical connections inside the junction box
located at the back of the unit (Fig.8).
• Installation of this product must be made in
accordance with all national and local building codes.
• The electrical connections must be made with a
12-gauge 2-conductor wire complete with ground.
CAUTION! BEFORE LETTING GO OF THE UNIT, CHECK THAT IT IS SECURELY
HUNG ON THE TWO SCREWS
6. Secure the unit with the third screw at the bottom .(Fig.6)
The Fig.7 on the right indicates the airflow generated by the heater. This air corridor
must remain clear in order to allow good air circulation and to ensure that the unit
operates efficently. Leave a space of at least 12 in (305mm) from the front and 24 in
(600mm) from the floor.
Do not install the heater below an electrical convenience outlet.
• The heater must be installed by a certified electrician and in accordance with the local
and national building codes.
• This fan heater is to be used on a 240 V AC power supply and grounded outlets.
Fig.5 Fig.6 Fig.7
Minimum
24” (600mm)
Minimum
12” (305mm)
Air outlet Air intake
OPERATION
6
ELECTRICAL CONNECTIONS
The fan heater has two knobs, one for the 60-minute timer
and one for the thermostat.
THE UNIT HAS TWO OPERATING MODES:
ROOM WARM-UP WITH TEMPERATURE CONTROL
From the position marked “ “, turn the thermostat knob clockwise until a clicking noise
is heard; the unit is turned on at a power of 1200 W and the warning light comes on.
The thermostat maintains the required room temperature by automatically turning on
and off the fan heater. The more you turn the knob clockwise, the higher the constant
temperature will be. The thermostat maximum setting is about 35 °C and the minimum
setting “ “ is about 5 °C.
THERMOSTAT
TIMER
HEATING ELEMENT
800W
1 200W
HEATING ELEMENT
INDICATOR LIGHT
FUSE THERMAL CUT-OFF
PROTECTION
MOTOR
L1
L2
OPERATION
7
Setting the thermostat:
With a room temperature above 35 °C, it is normal for the thermostat to not turn on the
fan heater, even at the maximum setting.
With a room temperature too low (under 5 °C), it is normal for the thermostat to
maintain the unit on, even at the minimum setting.
To optimize thermostat usage:
• Set the thermostat to the maximum setting and operate the unit until a comfortable
temperature is reached;
• Then, turn the thermostat knob counter-clockwise until a click is heard (the unit is
turned off);
• Slightly turn (just a little) the thermostat knob clockwise; At this setting, the thermostat
maintains the chosen room temperature.
QUICK ROOM WARM-UP
With the room temperature set at the required level, turn the timer knob to select the
required operating time. The unit operates at 2000 W for the set time to quickly heat
the room and then maintains the room temperature set by the thermostat at a power of
1200 W.
SAFETY IN CASE OF ABNORMAL OPERATION
In the event the unit overheats, the built-in protection system automatically deactivates
the heating elements and the motor, effectively stopping the fan heater operation. In
this case, the unit is inactive, but the warning lamp is on.
In this case, follow these instructions:
• Turn off the fan heater and let it cool for about 15-20 minutes. It is imperative to set
the thermostat and the timer to the “OFF” position in order to re-start it;
• Check if the dust filter is blocked and if so, clean and reinstall it;
• Locate potential overheating factors (i.e. obstruction in front of the air outlet or inlet
grille, unusual dirt accumulation, etc.);
• Turn the fan heater on again and check for proper operation. If you cannot get your
unit to work, contact Customer service at 1-866-967-7333.
8
Maintenance
1) Always turn off the heater before cleaning.
2) Do not knock against or rub the heater to avoid damaging the exterior coating, which
may allow rust to appear.
3) Never immerse the heater in water for cleaning.
• To reduce the risk of fire or electric shock, always switch off the unit and wait 10
minutes to allow it to cool before attempting any maintenance or cleaning. It is
recommended that the heater be cleaned periodically, in order to avoid dust blocking
the grill or ventilation.
MAINTENANCE & CLEANING
Cleaning
Wipe the unit with a soft damp cloth. Do not use abrasive
cleaners or spray liquids on the unit surfaces.
Your unit has a filter protecting the heating elements
against dust and dirt.
The filter can be removed and inserted from the right or
the left side.
For optimal operation, we recommend cleaning the filter once every 2 months and
making sure to reinstall it properly on the unit.
Regularly vacuum the front grille to remove the dust. Accumulated dust and lint at the
air outlet can reduce the unit’s performance and even damage it. To clean the unit, use
a slightly damp cloth. Note that cigarette smoke can cause unit's color to fade, despite
regular cleaning.
Note:
• It is possible that the unit surface may discolor (yellow) over time due to dust or
cigarette smoke. This is normal and not a manufacturing defect.
9
WARRANTY
LIMITED ONE (1) YEAR WARRANTY
This product is guaranteed against all manufactured faults and defects for a period of
one (1) year from the date of purchase. If your unit has a manufactured fault or defect,
return the unit to the original point of purchase (store) with your proof of purchase on
hand or call our customer service department at 1-866-967-7333.
Important notes: Any damage caused by an accident or an abusive usage is NOT
covered under warranty. We also decline all responsibility concerning indirect or
consecutive damages. In certain Canadian provinces, it is not permitted to limit indirect
or consecutive damages. Therefore it is possible these limitations are not applicable to
you. This warranty gives you specific legal rights. You may also have other legal rights
which vary from one province to another.
CUSTOMER SERVICE: 1-866-967-7333 ext 227
Indice
Lingue:
Altri manuali Ener-G+ Stufa
Ener-G+
Ener-G+ HEA-21538 Manuale utente
Ener-G+
Ener-G+ HEA 22000BHR Manuale utente
Ener-G+
Ener-G+ HEA 21531 Manuale utente
Ener-G+
Ener-G+ HEA 21523 Manuale utente
Ener-G+
Ener-G+ HEA-14756 Manuale utente
Ener-G+
Ener-G+ HEA 21723 Manuale utente
Ener-G+
Ener-G+ HEA 21524 Manuale utente
Ener-G+
Ener-G+ HEA-21548-BB Manuale utente
Ener-G+
Ener-G+ HIW-750 Manuale utente
Manuali Stufa popolari di altre marche
Empire Heating Systems
Empire Heating Systems WCC65 Manuale utente
Wetekom
Wetekom 92 86 43 Manuale utente
Desa
Desa SPC170-F Manuale utente
Watlow
Watlow Watrod Electric Tubular Heaters Manuale utente
Haverland
Haverland ECO-DRY GPS Series Manuale elenco delle parti
Stelpro
Stelpro ASILVC2060 Series Manuale utente