Enertexbayern Enertex KNXnet/IP Router Guida rapida

Manual and Configuration

KNXnet/IP Router

Enertex® Bayern GmbH – Ebermannstädter Straße 8 - 1301 Forchheim - Deutschland - mail@enertex.de

1147-HB-KNXnetIP-Router-en-1.odt, 2018-08-06 Seite 2 von

Note

The contents of this document may be reproduced without prior written approval by Enertex® Bayern

GmbH in any form, neither in whole nor in parts, copied, transmitted, distributed or stored.

Enertex® is a registered trademark of Enertex® Bayern GmbH. Other product and company names men-

tioned in this manual may be the marketing or trade names of their respective owners.

This manual may be changed without notification or announcement and makes no claim to completeness

or accuracy.

Table of content

Notices........................................................................................................................................................... 3

Assembly and connection...........................................................................................................................3

Commissioning............................................................................................................................................ 3

Functional escription................................................................................................................................ 4

ETS-Topology............................................................................................................................................... 4

Parameterization.......................................................................................................................................... 4

General..................................................................................................................................................... 4

IP settings................................................................................................................................................. 4

Routing (KNX → IP)................................................................................................................................. 5

Routing (IP → KNX) ................................................................................................................................ 6

Telnetserver.................................................................................................................................................. 6

Reset to factory defaults.............................................................................................................................8

ETS product data.......................................................................................................................................... 8

Technical data.............................................................................................................................................. 8

Obligation for distributors under § 18 (1) Battery Act .............................................................................9

Enertex® Bayern GmbH – Ebermannstädter Straße 8 - 1301 Forchheim - Deutschland - mail@enertex.de

1147-HB-KNXnetIP-Router-en-1.odt, 2018-08-06 Seite 3 von

Notices

•Installation and assembly of electrical equipment must be performed by qualified electri-

cians.

•When connecting KNX/EIB interfaces skills are provided by KNX™-Training.

•Ignoring the instructions may damage the device as well as causing fire or other ha-

zards.

•This manual is part of the product and must remain with the end user.

•The manufacturer is not liable for any costs or damages incurred by the user or third

parties through the use of this device, misuse or malfunction of the connection, malfunc-

tion of the device or the subscriber equipment.

•Opening the case or other authorized changes or modifications will void the warranty!

•The manufacturer is not liable for improper use.

Assembly and connection

Requirements:

•One of the following power supplies

- 20 bis 30 V DC

- 16 bis 24 V AC

- „Power over Ethernet“ (IEEE 802.3af), Class 1

- AUX-Output of the Enertex® KNX PowerSupply 60 if there is no additional KNX choke

connected to it

•10/100 Mbit compatible Ethernet connection

•KNX/EIB bus connection

Commissioning

LCD shows product name and firmware version at startup. Bootti-

me is about 2 seconds.

The default network setting ist DHCP.

If the DHCP server has transmitted a valid IP address to the devi-

ce, it is shown in the first line of the LCD with the prefix „D“.

If you set a static IP „S“ occurs or rather „Z“ for a IP address pro-

cured via Zeroconf.

In the second row the KNX pysical address is displayed (prefix „K“). To use the routing functions

it has to look like „x.y.0“ or „x.0.0“ (x,y: value between 0 and 15).

„T“, followed by a number between 0 and 5 shows the number of the open tunnel connection.

The green LED signalizes LAN activity, the yellow LED signalizes KNX bus activity. If the the red

LED is active, device is in programming mode.

Enertex® Bayern GmbH – Ebermannstädter Straße 8 - 1301 Forchheim - Deutschland - mail@enertex.de

1147-HB-KNXnetIP-Router-en-1.odt, 2018-08-06 Seite 4 von

Functional escription

•Five independent KNXnet/IP tunnel connections

•KNXnet/IP Routing for communication between KNX lines, areas und systems via IP network

•Telegram routing and filtering according to pysical address or group address

•LED-signaling for KNX communication, Ethernet communication and programming mode

•Standard configuration with ETS

•Configuration of the tunnel addresses via Telnet

•SNTP Server with battery-buffered real-time clock

ETS-Topology

To add the device in a ETS project, the project needs a IP-Backbone, as shown in the following

example:

Lines:

•0.0: Medium IP

•1.0: Medium IP

•1.1: Medium TP

Parameterization

The device can be parameterized with ETS3, ETS4 or ETS5. It supports up to five tunnel

connections and can be used as a line- or area coupler.

General

evice name You can assign a user-defined name here (up to 30 characters).

Bus power failure monitoring Reports a KNX bus failure to the IP network, als well as the re-

storation.

Parameter: enabled, disabled

IP settings

IP assignment method The IP address can be assigned via DHCP, Manually or Zeroconf.

Parameter: manuell, DHCP, Zeroconf

Enertex® Bayern GmbH – Ebermannstädter Straße 8 - 1301 Forchheim - Deutschland - mail@enertex.de

1147-HB-KNXnetIP-Router-en-1.odt, 2018-08-06 Seite 5 von

Routing Multicast Address This address will be used for routing telegrams on IP side. The

Multicast IP Address 224.0.23.12 has been reserved for this purpose (KNXnet/IP Routing). If

you want to assign another address it has to be in the range between 224.0.0.0 and

23 .255.255.255.

IP Address (only for manual assignment)

Parameter: valid IP address in your net ork

Subnet Mask (only for manual assignment)

Parameter: valid subnet mask

efault Gateway (only for manual assignment)

Parameter: valid IP address in your net ork

Routing (KNX → IP)

Group telegrams of main group 0 to 13 Via routing group telegrams can be forwarded,

Enertex® Bayern GmbH – Ebermannstädter Straße 8 - 1301 Forchheim - Deutschland - mail@enertex.de

1147-HB-KNXnetIP-Router-en-1.odt, 2018-08-06 Seite 6 von

blocked or filtered. You can parameterize the behaviour of the main groups 0 to 13 different to

the behaviour of the main groups 14 to 15. If you choose „filter“, ETS will select the relevant tele-

grams to route automatically.

Parameter: filter, block, route

Group telegrams of main group 14 to 15

Parameter: block, route

Physically addressed telegrams Physically addressed telegrams (e.g. programming of actua-

tors) can be routed, blocked or filtered.

Parameter: filter, block, route

Broadcast telegrams

Parameter: block, route

Routing (IP → KNX)

Group telegrams of main group 0 to 13 Via routing group telegrams can be forwarded,

blocked or filtered. You can parameterize the behaviour of the main groups 0 to 13 different to

the behaviour of the main groups 14 to 15. If you choose „filter“, ETS will select the relevant tele-

grams to route automatically.

Parameter: filter, block, route

Group telegrams of main group 14 to 15

Parameter: block, route

Physically addressed telegrams Physically addressed telegrams (e.g. programming of actua-

tors) can be routed, blocked or filtered.

Parameter: filter, block, route

Broadcast telegrams

Parameter: block, route

Telnetserver

A integrated Telnet server provides additional functionalities. The default password for Telnet ac-

cess is „knxnetip“.

date Show time (UTC) and date

factory_reset Reset the device to factory default and restart

ifconfig Show IP settings

Sys multicast: multicast address for system telegrams

RT multicast: multicast address for routing telegrams

Enertex® Bayern GmbH – Ebermannstädter Straße 8 - 1301 Forchheim - Deutschland - mail@enertex.de

1147-HB-KNXnetIP-Router-en-1.odt, 2018-08-06 Seite 7 von

lcconfig Show KNXnet/IP routing setting

IP->KNX: settings for telegrams from IP to KNX

KNX->IP: settings for telegrams from KNX to IP

GA 0-13: group telegrams of main groups 0 to 13

GA 14-15: group telegrams of main groups 14 to 15

Ph. addr.: physical addressed telegrams

Broadcast: broadcast telegrams

PW fail. mon.: power fail monitor

logout Close Telnet session

passwd oldpw newpw

passwd oldpw

passwd newpw

Change Telnet passwort (passwd old new),

Delete passwort (passwd old)

Set passwort, if no password is set already (passwd new)

lock [0|1] Show „Lock“ status (without option) or change lock mode (0 = off, 1 = on)

With filtering a router can prevent forwarding of physically addressed telegrams, which makes

it impossible to re-program devices at another line. That's important for outside areas/lines.

Though it's possible to re-program the router itself to enable routing of physical addressed

telegrams by accessing the bus at an outdoor line with e.g. a USB-KNX-Interface.

This can be prohibited by this Telnet function. Set „lock“ to 1 to disable reprogramming of the

router.

progmode [0|1] Show programming mode status (without option) or set programming mode (0 = off, 1 = on)

reboot Restart device

sntp [query|server IP] Send ntp query (sntp query) or set IP address of the NTP server (sntp server

1.2.3.4)

stats Show statistics

uptime: uptime since last reboot

TX to IP (all): number of telegrams sent to IP

TX to KNX: number of telegrams sent to KNX bus

RX from KNX: number of telegrams received from KNX bus

Overflow to IP: number of telegrams, that couldn't be sent to IP

Overflow to KNX: number of telegrams, that couldn't be sent to KNX bus

TX tunnel re-req: number of telegrams, that had to be repeated during tunnel access

tpconfig Show KNX parameters

KNX bus state: KNX bus detected (up) or not detected (down)

KNX address: physical address of the device

Serial number: serial number of the device

Enertex® Bayern GmbH – Ebermannstädter Straße 8 - 1301 Forchheim - Deutschland - mail@enertex.de

1147-HB-KNXnetIP-Router-en-1.odt, 2018-08-06 Seite 8 von

tunaddr 1..5 address

tunaddr reset Change tunnel address for each tunnel e.g. tunaddr 1 15.15.240 or reset tunnel

addresses to factory default (tunaddr reset)

tunnel [1..5] Show tunnel addresses and connection status (without option), or show detailled information

for a specific tunnel (option 1..5)

CCID: connection id of the tunnel connection

KNX address: tunnel address

HPAI control: control-end-point of the receiver

HPAI data: data-end-point of the receiver

Connect. Type: tunnel connection or management connection

TX tun req: number of telegrams sent to this tunnel

TX tun re-req: number of telegrams that had to be repeated for this tunnel connection

RX tun req: number of telegrams received from this tunnel

RX tun re-req: number of telegrams that have been received twice for this tunnel connection

RX tun req (wrong seq.): number of telegrams with wrong sequence number that have been

received for this tunnel

version Show firmware version

Reset to factory defaults

To reset the device to factory defaults, press and hold the programming mode button for three

seconds. When the red LED starts blinking release the button. The device shuts down and will

reboot with factory settings automatically.

ETS product data

You can download the latest version of the product's ETS database from our homepage:

http://www.enertex.de/e-downloads01.php

Technical data

Power supply 16-24 V AC or 20-30 V DC; IEEE 802.3af („Power over Ethernet“)

Power consumption Max. 1 W

Display 2-line LCD

KNX functions KNXnet/IP tunneling and routing

Enertex® Bayern GmbH – Ebermannstädter Straße 8 - 1301 Forchheim - Deutschland - mail@enertex.de

1147-HB-KNXnetIP-Router-en-1.odt, 2018-08-06 Seite von

KNXnet/IP routing Up to 48 telegrams per second

KNXnet/IP tunneling Up to 35 telegrams per second, up to five tunnel connections

NTP SNTP Server, battery-buffered

Obligation for distributors

under § 18 (1) Battery Act

Dear customer, you bought a battery operated product from us. Although the battery life is very

long, it still needs to be disposed someday. Used batteries should not be put in the household

garbage. Consumers are required by law to bring batteries to a suitable collection point. You can

also send your used batteries to

Enertex Bayern GmbH

Ebermannstädter Str. 8

1301 Forchheim

Deutschland

Old batteries contain valuable raw materials that can be recycled.

The environment and Enertex Bayern GmbH say thank you.

The garbage bin symbol means: Batteries and rechargeable batteries must not be

disposed of with household waste.

Enertex® Bayern GmbH – Ebermannstädter Straße 8 - 1301 Forchheim - Deutschland - mail@enertex.de

Altri manuali per Enertex KNXnet/IP Router

Indice

Altri manuali enertexbayern Router di rete

enertexbayern

enertexbayern Enertex KNX IP Secure Router Guida rapida

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza

enertexbayern Enertex KNXnet/IP Router Guida rapida

Manuali Router di rete popolari di altre marche