Enerwave ZWN-BPC-PLUS Manuale utente

INSTALLATION NSTRUCTIONS

WARRANTY INFORMATION

Model: ZWN-BPC-PLUS

Wireless Home Automation Control Device

Ceiling mounted PIR Motion Sensor

0209160053-03

INSTALLING Z-WAVE DEVICES

LOCATIONS

Installation of Z-Wave devices instantly increases the functionality, efficiency, and value of your home. The more devices you install, the more efficient your house will be. The most effective

locations to install Z-Wave devices are in the Living Room, Bedrooms, Kitchens, Family Rooms, Guest Rooms, and Entertainment Rooms.

This device complies with the Z-Wave standard of open-air, line of sight transmission distances of 131 feet. Actual performance in a home depends on the numbers of walls between the

remote controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in the control network. Z-Wave devices act as signal repeaters ONLY

after they are "Included" on the network. This device's signal repeater is disabled, however uses repeated signals from other Z-Wave devices to increase it's signal range.

This device is warranted to be free of material and workmanship defects for 2 years from the date of

purchase. Original receipt or proof of purchase from an authorized retailer must be presented upon warranty

claim. ALL claims must be verified and approved by Enerwave, Inc. Warranties from other Enerwave

products may vary. This warranty is nontransferable and does not cover normal wear and tear or any

malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper

installation. To the fullest extent permitted by the applicable state law, Enerwave shall not be liable to the

purchaser or end user customer of Enerwave products for direct, indirect, incidental, or consequential

damages even if Enerwave has been advised of the possibility of such damages. Enerwave’ total liability

under this or any other warranty, express or implied, is limited to repair, replacement or refund. Repair,

replacement or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.

DESCRIPTION

The ZWN-BPC-PLUS is PIR Motion Sensor with Z-Wave technology. This sensor

can be used to turn on devices that are connect to the same Z-Wave network. For

the advanced users, the functions are programmable for setting scenes,

associations and scheduling events.

FEATURES

•No wiring required. Battery operated.

•Wireless Z-Wave technology creates a mesh network for command and

control interoperability with other Z-Wave compliant controllers and devices.

•Remotely control of any load connected to a Z-Wave device on the network.

•Reduce energy consumption and enjoy wireless home automation.

•PIR Sensitivity Control.

•Low Battery warning.

REQUIREMENTS

Z-Wave devices require a connection to a compatible hub. Once the device is

properly added to the Hub, it can be managed and customized to your needs. Please

visit www.enerwaveautomation.com for a list of compatible hubs.

SPECIFICATIONS

Power Supply....................................................................................2AA Batteries

PIR Sensitivity Adjustment.................................................25%/ 50%/ 75%/ 100%

Z-Wave Frequency.............................................................................. 908.42 MHz

Operating Temperature........................................................................... 32-104° F

FCC COMPLIANCE STATEMENT

FCC Grant of Equipment Authorizations of this device and transmitters installed in this device can be found at FCC website by entering the FCC ID number on the device.

Caution: Changes or modifications not expressly approved by the part responsible for compliance could void the user’s right to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation of the device.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

WARNING:

Read and understand these instructions before installing. Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room than the controlled appliance so an unintentional activation may occur if the wrong button

on the remote is pressed. Z-Wave devices can be automatically powered on by programmed events. Unattended or unintentional operation could result in hazardous conditions. Z-Wave enabled devices should never be used to supply power to, control, or monitor medical and/or life

support equipment.

•During the Inclusion/ Exclusion process, the Sensor must be removed from it's mounting bracket in order to

reach the Inclusion/ Exclusion button on the back of the device.

•It is best to perform an EXCLUSION of the device prior to performing an Inclusion.

Step 1. From the Control Panel, go the the device Exclusion page.

OPERATING THE ZWN-BPC-PLUS

Once the ZWN-BPC-PLUS is configured, the devices associated with the sensor will turn ON when motion is detected and OFF

when the area is vacant. They can also be operated from your desktop on the control panel provided on the Hub manufacturer's

website or a smart device such as the iPhone, iPad or any Android device once the appropriate App is installed on the device.

PROGRAMMING

ZWN-BPC-PLUS

DEVICE INCLUSION/ EXCLUSION

The process of "Inclusion/ Exclusion" is to Add or Remove the device from the Hub. All Z-Wave devices must be "Included" on the Controller (Hub) before it can

be controlled from a smart device. The Hub should be brought physically closer to the device just for the "Inclusion" process (recommended within 10ft). When

finished, the Hub and device can be moved back to final installation locations. Download the App or log onto the website associated with the Hub you are using

and follow their Inclusion/ Exclusion instructions as each Hub's programming and features are different.

ADVANCED PROGRAMMING

oSelect "Exclude Device".

oWhen prompted, press and hold the exclusion button on the sensor for 3 seconds.

Step 2. Go to the "Add Device" page.

oSelect "Include Device".

oWhen prompted, press and hold the inclusion button on the sensor for 3 seconds.

The primary controller should indicate that the action was successful. If the controller indicates the action was

unsuccessful, please repeat from Step 1. Once the module is part of the network, the same basic procedure is used to add

the switch to groups & scenes or change advanced functions. Refer to the primary controller’s instructions for details.

WARNING: Advanced programming is recommended ONLY for experienced programmers. The ZWN-BPC-PLUS has customizable

features/functions that require writing codes. Changes to code may cause device to function improperly or to not function at all.

The following parameters require that you have an advanced controller. Basic remotes do not have this capability.

Wakeup command class

The motion sensor will send a wakeup notification command if it has been added to a Z-Wave network. The motion sensor will wake up

periodically (default is 30 minutes) depending on the time interval you set from wakeup command class. The motion sensor will stay awake

for 10 seconds and then go back to sleep to conserve battery life. It will also go to sleep when it receives the command WAKEUP_

NO_MORE_NOTIFICATION.

Specification for WAKEUP_INTERVAL_SET:

•0x00003C Minimum value (Equal to 60 seconds)

•0x015180 Maximum value (Equal to 68400 seconds, or 24 hours)

•0x00003C Default value (Equal to 60 seconds, or 1 minutes)

•0x000000-0x00003B, 0x015181-0xFFFFFF, these values will be ignored.

Configuration Command Class

Configuration parameter can be used to adjust the delay time of sending basic set off command after motion

sensor sends the basic set on when motion detected.

The motion sensor can be woken up manually: press and hold the program switch for one second and release. The

switch it will send broadcast wakeup notification or single-cast wakeup notification to associated devices.

For some controllers, after configuration and association setting, it's necessary to wake up the ZWN-BPC-PLUS manually

by pressing the program button.

Battery command class

ZWN-BPC will check the battery power level every day and report the battery level by sending broadcast

(BATTERY_REPORT, value 0x64). Or else when battery level is greater than 2.6V, it will send singlecast command

(BATTERY_REPORT, value 0x10). Or else when battery level is greater than 2.4V, it will send singlecast command

(BATTERY_REPORT, value 0x00). Or else when battery level is less than 2.4V, it will send singlecast command

(BATTERY_REPORT, value 0xFF).User needs to replace new batteries.

Association command class

ZWN-BPC-PLUS can control devices by using this command class and COMMAND_CLASS_BASIC. If a device is

associated with ZWN-BPC-PLUS, the motion sensor will send basic on/off command to it when motion detected. Each

ZWN-BPC-PLUS can support 5 associations.

Step 3. Follow the On-Screen instructions in the Control Panel on adding or removing rooms, scenes, other devices, and

other functions and features. Be sure to Associate the ZWN-BPC-PLUS with All the devices to be operated with the

sensor.

Step 4. To reset the ZWB-BPC-PLUS manually, simply press and hold the exclusion button on the sensor for 10

seconds.

Parameter Size Description Valid Value

1 Byte

Default

NO. Value

It is minimum time when

the associated nodes

keep turn on (n*WAKE_UP

_INTERVAL)

Notification

V1 Alarm Type

V1 Alarm Level

Notification Type

Event

0x00

0x07

0x08

Association

Grouping ID Max number of nodes number of

1 1

3 5

Lifeline: 1.. Battery Repo

2.. Notification Repo

3.. Device Reset Local

Notification

Sensor Basic rep: Basic Report

Sensor Notifi rep: Notification Report

Sensor Basic set: Basic Set 0x00/0xFF

Altri manuali Enerwave Sensore di sicurezza

Enerwave

Enerwave ZWN-BPC Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente