ENFORCER PR-112S-A Manuale utente

ENFORCER Proximity Card Reader

12 SECO-LARM U.S.A., Inc.

WARNING

: Incorrect mounting which leads to exposure to rain or moisture inside the enclosure could cause a dangerous electric shock, damage the device,

and void the warranty. Do not open the case of this device, as there are no field-serviceable components inside.

WARRANTY

: This S CO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year

from the date of sale to the original consumer customer. S CO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned,

transportation prepaid, to S CO-LARM.

This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal

usage, or faulty installation, or if for any other reason S CO-LARM determines that such equipment is not operating properly as a result of causes other than

defects in material and workmanship.

The sole obligation of S CO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at S CO-LARM’s option. In no event

shall S CO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.

NOTICE

: The information and specifications printed in this manual are current at the time of publication. However, the S CO-LARM policy is one of continual

development and improvement. For this reason, S CO-LARM reserves the right to change specifications without notice. S CO-LARM is also not responsible for

misprints or typographical errors.

S CO

LARM.

Troubleshooting:

16842 Millikan Avenue, Irvine, CA 92606

Tel:

800

662

0800 / 949

261

2999

PICGN1

MiPR-112S-A_1406.docx

Website: www.seco

larm.com

mail: sales@seco

larm.com

The L D does not light

•Check the power connection

•Check the power supply

The relay does not activate

•Make sure you are using a valid user card

•Make sure the relay is not in toggle mode

•Make sure the correct relay output is being used

(either N.O. or N.C.)

The relay time is too short •Set a longer door-release time

gress button not working

•Make sure you are using a N.O. switch

•Double-check the door-release time

•Double-check the relay toggle mode

Also Available from

Electromagnetic Loc s

Electric Door Stri es

Request

Exit Plates

80, 300, 600, and 1,200

Holding force available

Different sizes and

applications available

Different sizes and

button types available

•

Stand-alone operation

•Sealed and weatherproof (IP67)

•Tri-color L D status bar

•

Up to 100 user cards

•Up to 5 master cards

•10 Cards included

PR-112S-A

Proximity Card Reader

Manual

ENFORCER Proximity Card Reader

2SECO-LARM U.S.A., Inc.

Introduction

................................

..............

Specifications .......................................... 2

Parts List.................................................. 2

Features .................................................. 3

Dimensions .............................................. 3

Installation Instructions ............................ 4

Wire Coding ............................................. 4

Sample Installation .................................. 4

Table of Contents:

Mounting Diagram

................................

...

Getting Started ........................................ 5

Programming ........................................ 6-8

Operating Instructions.............................. 9

System Reset ........................................ 10

User List ................................................ 11

Troubleshooting ..................................... 12

Introduction:

The NFORC R PR

112S

A Proximity Card Reader provides a flexible solution for

securing controlled access. The stylish case and small size make it ideal for use in most

residential, commercial, and industrial sites. The wave-shaped L D status bar accents

the case design. Simple installation, quick programming, high reliability, and attractive

design are all combined in the PR-112S-A.

Specifications:

Power input

12VDC

Current draw

Standby: 80mA@12VDC

Active: 200mA@12VDC

Max. read distance

6” (15cm)

User card limit

100 cards

Master card limit

cards

Transmit frequency

125kHz

Outputs

1 relay (N

O/NC/

COM)

Contact rating

1A@30V

Relay time delay

1~180

secs/

Toggle mode

Temperature

4°~158°

F (

20°~70°

Enclosure rating

IP67

Dimensions

”x1

”x

” (95x44x1

mm)

Parts List:

1x Prox

imity card reader

10x Proximity cards

(1 Pre-programmed master card; 9 blank cards)

1x Manual

Additional Accessories Available

from

K1K1

K1S1

Proximity key fobs

(sold in packs of 10)

Proximity cards

(sold in packs of 10)

ENFORCER Proximity Card Reader

SECO-LARM U.S.A., Inc. 11

User List:

User User Name Card #

NOTE

–

Please make and use a copy of the chart and store the original in a

safe place.

ENFORCER Proximity Card Reader

10 SECO-LARM U.S.A., Inc.

System Reset:

Should it be necessary to completely reset the proximity reader, follow this procedure:

Disconnect power to the proximity reader.

Ground the BLU wire:

a. If the egress button is connected, DO NOT open the case. Just press and hold the

egress button.

b. If the egress button is not connected, you must unscrew the proximity reader from the

wall, and ground the BLU wire.

While either pressing the egress button or grounding the BLU wire, reconnect power. The

L D will start to blink GREEN. Continue pressing the egress button or grounding the BLU

wire.

After about 3 seconds, the proximity reader should sound two long beeps. At this point,

release the egress button or unground the BLU wire.

NOTE – If a mistake is made, just restart this process from step 2 above.

After a few seconds, the proximity reader will sound 3 beeps and the L D will start flashing

GREEN rapidly. After about 5 seconds, the L D will flash more slowly. At this point, tap any

card to the proximity reader. This is now the first master card.

NOTE

–

After a system reset, all cards except the new master card are now considered to be

blank cards.

Flash

5 sec.

BLU : gress input

BLACK: Ground

12VDC

Power

N.O. gress Switch

Cut

power

ENFORCER Proximity Card Reader

SECO-LARM U.S.A., Inc. 3

Features:

•

Stand-alone operation.

•Use in small businesses, homes, parking structures, apartments, and other locations.

•Sealed and weatherproof (IP67).

•Mounts easily to interior and exterior walls.

•Attractive tri-color wave-shaped L D status bar indicates proximity reader’s mode and status.

BLUE

: On/valid card indicator

GREEN

: Programming mode

RED: Invalid card

•

Relay output can be programmed for timed (1~180 seconds) or toggle mode.

•

gress input for simple egress of the protected area.

•

Buzzer is programmable for audible confirmation or silent mode.

•

Up to 100 user cards can be programmed.

•

User cards are easily deleted.

•

Up to 5 master cards can be programmed.

•

Proximity cards – When placed within 6” (15cm) of the proximity card reader, a valid card will

grant access to the protected area. 10 Cards included.

(Additional cards available. Model #: PR-K1S1-A. Sold in packages of 10.)

Dimensions:

Front

Back

(Mounting Plate)

Side

” (44mm)

”

(95mm)

”

(19mm)

”

(21mm)

”

(21mm)

”

(17mm)

”

(21mm)

”

(40mm)

”

(16mm)

ENFORCER Proximity Card Reader

4SECO-LARM U.S.A., Inc.

Installation

Instructions:

Unpack the unit and familiarize yourself with the proximity reader and the included parts.

2. Test the mounting location for fit.

3. Using a T-10 Torx driver (not included), remove the screw from the bottom of the proximity

reader and separate the outside case from the base.

4. Place the base on the mounting location, and then mark the two mounting holes and the

wire-harness hole.

5. Drill a

” hole for the proximity reader’s wire harness.

6. Permanently screw the base into the mounting location.

7. Run the wires from the power supply, egress button, and door unlock device through the

hole to connect to the wire harness.

8. Connect the wires to the proximity reader’s wire harness. Solder or crimp the connections

and carefully insulate them.

9. Reattach the outside case to the base.

10. The preliminary installation is done. Now program the proximity reader.

Wire Coding:

R D

—

(+) 12VDC

BLACK

—

(

–

) GND

BLU

—

gress input (N.O., ground)

Y LLOW

—

N.C. Output

Relay,

1A@30VDC

GR N

—

N.O. Output

BROWN

—

COM

Sample Installation:

Key notch for

attaching unit to base

Screw mounting hole

Wiring

harness

access hole

Screw mounting hole

Nut for base

attachment screw

Back

BLU : gress input

(N.O., ground)

BLACK: Ground

BROWN: COM

Y LLOW: N.C. (output)

R D: 12VDC

12VDC

Power

lectromagnetic

lock

GR N: N.O. (output)

gress

switch

ENFORCER

SECO-LARM U.S.A., Inc.

Operating Instructions

Entering the Premises

–

User Card

To enter a protected premise, tap the proximity

reader one time with a user card. The L D

turns off momentarily, the proximity reader

sounds one short beep, and the relay output

engages for the programmed time.

Exiting the Premises

–

Egress Button

To exit a protected premise,

press the egress button

once. The L D turns off

momentarily, the proximity

reader sounds one short

beep, and the relay output

engages for the

programmed time.

Using an Invalid Card

If the proximity reader is tapped using a blank

or invalid card, the L D flashes RED and the

proximity reader sounds one long beep.

ENFORCER

Proximity Card Reader

Beep

…

ENFORCER Proximity Card Reader

8SECO-LARM U.S.A., Inc.

Set the relay toggle mode

(Timed output or toggle; default: timed output)

Action

Reaction

Tap a master card 8 times

2 Beeps after first tap, 1 more beep after each

subsequent tap, L D flashes GREEN

Wait 3 seconds

8 Beeps,

GREEN

flashes continue

Wait a second, and the mode

changes automatically

Beeps 1 time = normal mode

Beeps 2 times = toggle mode

xit

–

The unit

automatically exits to standby mode

Normal mode – Use a user card to unlock the door, the door automatically locks after the

timer has expired.

Toggle mode – Use a user card to unlock the door, then use a user card to relock the door.

Please note

that tapping the master card 9 times will have no effect.

10.

Set the beeper mode

(ON or OFF; default: ON)

Action

Reaction

Tap a master card 10 times

2 Beeps after first tap, 1 more beep after each

subsequent tap, L D flashes GREEN

Wait 3 seconds

10 Beeps,

GREEN

flashes continue

Wait a second, and the mode

changes automatically

Beeps 1 time = beeper OFF

Beeps 2 times = beeper ON

xit

–

The unit automatically exits to standby mode

NOTE – When the beeping is programmed OFF, the proximity reader will still beep during the

programming mode.

ENFORCER Proximity Card Reader

SECO-LARM U.S.A., Inc. 5

Mounting Diagram:

Getting Started:

Card Types

There are three basic types of cards used by the proximity reader:

•Master card – Used for programming only. It does not give access to the protected premises.

•User card – Used for access only.

•Blank card – A card that has not yet been programmed into the proximity reader. Considered

to be an invalid card.

NOTE – The proximity reader can learn up to 5 master cards and 100 user cards.

LED Color Indicators:

LED Color Status Indicated

BLUE

The proximity reader is

powered on

and in

standby mode

GREEN

The proximity reader is in

programming mode

Indicates an

error

invalid card

First-Time Power Up:

1. After connecting power, the unit should beep once and the L D should be BLUE – The

proximity reader is ready to be programmed using the included pre-programmed master card

(marked with a red sticker).

2. If after connecting power for the first time the L D is flashing GREEN, you must program a

master card by tapping any blank card to the reader.

3. This will be followed by 2 short beeps and the L D should turn BLUE.

4. The proximity reader is ready to be programmed using the master card you just created.

Included

case screw

Mounting

plate

Proximity

card

reader

Screw for mounting

plate to surface

Through

hole for

cables

ENFORCER Proximity Card Reader

6SECO-LARM U.S.A., Inc.

Programming:

Add a new user card:

Action

Reaction

Tap a master card 1 time

2 Beeps, L D flashes

GREEN

Wait 3 seconds

1 Beep,

GREEN

flashes continue

Tap a blank card 1 time

1 Beep, the card

is now a user card

Tap more blank cards 1 time each to

create more user cards 1 Beep for each new user card

xit

–

To exit programming mode, tap a master card 1 time or wait 15 seconds

NOTE – Attempting to add a previously-learned user card or master card will cause the unit to

beep twice and the L D to flash RED.

Delete the user card following this user card

Use this to delete a missing user card.

Action

Reaction

Tap a master card 2 times

2 Beeps after first tap, 1 more beep after second

tap, L D flashes GREEN

Wait 3 seconds

2 Beeps,

GREEN

flashes continue

Tap the user card that was added

just before the card to be deleted 2 Beeps, the desired user card is deleted

xit

–

To exit programming mode, tap a master card 1 time or wait 15 seconds

NOTE – Attempting to delete a blank card or a master card will cause the unit to beep twice

and the L D to flash RED.

Delete this user card:

Use this to delete a user card that is in your possession.

Action

Reaction

Tap a master card 3 times

2 Beeps after first tap, 1 more beep after each

subsequent tap, L D flashes GREEN

Wait 3 seconds

3 Beeps,

GREEN

flashes continue

Tap the user card to be deleted

3 Beeps, the user card is deleted

xit

–

To exit programming mode, tap a master card 1 time

or wait 15 seconds

NOTE – Attempting to delete a blank card or a master card will cause the unit to beep twice

and the L D to flash RED.

Delete all user cards:

Action

Reaction

Tap a master card 4 times

2 Beeps after first tap, 1 more beep after each

subsequent tap, L D flashes GREEN

Wait 3 seconds

4 Beeps,

GREEN

flashes continue

WITHIN 3 S CONDS, tap the

master card again. 4 Quick beeps, all user cards are deleted

xit

–

The unit automatically exits

to standby mode

ENFORCER Proximity Card Reader

SECO-LARM U.S.A., Inc. 7

Add a new master card

(

WARNING

–

Master cards cannot be deleted.

See pg. 10,

System Reset for instructions on clearing all cards from memory.):

Action

Reaction

Tap a master card 5 times

2 Beeps after first tap, 1 more beep after each

subsequent tap, L D flashes GREEN

Wait 3 seconds

5 Beeps,

GREEN

flashes continue

Tap a blank or user card

Beeps, the card is now a master card

Tap more blank or user cards 1 time

each to create more master cards 2 Beeps for each new master card

xit

–

To exit programming mode, tap a master card 1 time or wait 15 seconds

Set the door

release timer

(Default: 5 seconds):

Action

Reaction

Tap a master card 6 times

2 Beeps after first tap, 1 more beep after each

subsequent tap, L D flashes GREEN

Wait 3 seconds

6 Beeps,

GREEN

flashes continue

Count the beeps

1 Beep = 1 second for the door release timer

Tap the master card to stop the

beeps at the desired time The timer is now set for the number of seconds

xit

–

The unit automatically exits to standby mode

Show how many user cards have been programmed:

Action

Reaction

Tap a master card 7 times

2 Beeps after first tap, 1 more beeps after each

subsequent tap, L D flashes GREEN

Wait 3 seconds

7 Beeps,

GREEN

flashes continue

Wait 1.5 seconds

Silence

Count beeps for the first digit

Long beep = 0 or 1 beep = 1

Wait 1 second

Silence

Count beeps

for the second digit

Long beep = 0 or 1~9 beeps = 1~9

Wait 1 second

Silence

Count beeps for the third digit

Long beep = 0 or 1~9 beeps = 1~9

xit

–

The unit automatically exits to standby mode

Counting the beeps

–

The number of beeps indicates the value of each digit. All three digits

together give the number of user cards that have already been programmed.

Some examples:

Number of user cards

Beep sequence

Long beep / 1 beep / 3 beeps

Long beep / 2

beeps / 4 beeps

Long beep / Long beep / 7 beeps

100

1 Beep / Long beep / Long beep

Indice

Altri manuali ENFORCER Lettore di schede

ENFORCER

ENFORCER PR-312S-PQ Manuale utente

Manuali Lettore di schede popolari di altre marche

Lindy

Lindy 43185 Manuale utente

Lindy

Lindy 43185 Manuale utente

ViziT

ViziT RD-4F Manuale utente

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuale utente

AVID ID

AVID ID AVID1043 Manuale utente

Conrad

Conrad PCMCIA Manuale utente

Rosslare

Rosslare DR-6255 Manuale utente

Lindy

Lindy 51541 Manuale utente

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuale utente

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuale utente

ACS

ACS ACR122L Manuale utente

Secukey

Secukey S2-MF Manuale utente

Elecom

Elecom MR-SMC07 series Manuale utente

Alien

Alien ALR-9800 Manuale utente

ACS

ACS ACR310 Manuale utente

Datamars

Datamars R-IN1300 MID Manuale utente

Alarm Lock

Alarm Lock AL-PRE2 Manuale utente

xpr

xpr B100PROX-AH Guida utente