ENFORCER SD-7428-GSEQ Manuale utente

Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.

SD-7428-GSEQ

Request-to-Exit Button

with Delayed Egress Timer

User Manual

Programmable nuisance delay timer

(0~3 seconds) to prevent accidental door

unlocking

Adjustable pre-delay timer (1~30 seconds

until the door unlocks)

12~24 VDC Operation

Form C relay outputs for lock relay and

remote alarm relay

Built-in 100dB buzzer

Fits standard double-gang backbox

Keyswitch to re-energize door lock

IMPORTANT

Users and installers of this product are responsible for ensuring that the installation and configuration of this

product complies with all national, state, and local laws and codes related to locking and egress devices.

SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.

Replacement Keys: SD-7428-KEY (Sold in packs of 5)

ENFORCER Request-to-Exit Button with Delayed Egress Timer

2SECO-LARM U.S.A., Inc.

The Request-to-Exit Button with Delayed Egress Timer mounts to

a standard double-gang backbox. Use the four included mounting

screws to secure the double-gang plate to the backbox.

Introduction:

Specifications:

Operating voltage

12~24 VDC

Current draw

Standby

60mA@12VDC, 90mA@24VDC

Release delay

150mA@12VDC, 55mA@24VDC

Lock relay output

10mA@12VDC, 15mA@24VDC

Lock control output

3A@30VDC, Form C, NO/NC/COM

Remote alarm output

3A@30VDC, Form C, NO/NC/COM

Buzzer sound level

12VDC: 95db@1m, 24VDC: 100db@1m

Overview:

41/2” (114mm)

41/2”

(114mm)

23/4”

(70mm)

Front

Top

Pre-delay

potentiometer

Terminal block

Nuisance delay

jumpers

Buzzer

Request-to-exit

button

Keyswitch

Parts List:

1x Request-to-Exit

Button with Delayed

Egress Timer

4x Mounting screws

2x Keys

1x Manual

Replacement Keys:

SD-7428-KEY

(Sold separately in packs of 5)

Side

Mounting:

The SD-7428-GSEQ allows for a controlled exit from a room protected by an electromagnetic

door lock. To exit the room, press the large green button until the built-in buzzer sounds, at

which time a programmed pre-exit delay timer begins. After the delay, the door unlocks and

stays unlocked. To relock the door, use the included keys to turn the keyswitch.

13/16”

(20mm)

115/16”

(50mm)

ENFORCER Request-to-Exit Button with Delayed Egress Timer

SECO-LARM U.S.A., Inc. 3

Nuisance delay

0 Seconds

1 Second

2 Seconds

3 Seconds

JP1

OFF

JP2

OFF

Wiring Diagram:

Remote alarm relay output

(3A@30VDC, Form C Relay, NO/NC/COM)*

Lock relay output

(3A@30VDC, Form C Relay, NO/NC/COM)*

Power input (12~24 VDC)

Sample Application:

Delayed exit from a building:

Power

supply

Strobe light

Electromagnetic lock

1. An electromagnetic lock, such as the E-941SA-1200, is connected to the lock relay output.

2. A strobe light, such as the SL-1301-BAQ, can be connected to the remote alarm relay output.

This device will signal at a remote location whenever the remote alarm relay output is triggered.

Adjusting the Pre-Delay:

The pre-delay can be adjusted using the potentiometer located

on the circuit board. The pre-delay timer can be adjusted from

1~30 seconds. This sets the duration of time between the end

of the nuisance delay and when the door will unlock.

Adjusting the Nuisance Delay:

The nuisance delay determines how long the push button must

be activated before the pre-delay timer will start. The nuisance

delay can be programmed from 0~3 seconds.

NOTE: The nuisance delay is preset to 3 seconds.

Example:

Set to 0 seconds

N.C.

COM

N.O.

Remote

Relay

Alarm

Output

N.C.

COM

N.O.

Lock Relay

Output

12~24 VDC

N.C.

COM

N.O.

Lock Relay

Output

N.C.

COM

N.O.

Remote

Relay

Alarm

Output

*Normally energized. (Screen print refers to energized state as normal.)

Potentiometer

ENFORCER Request-to-Exit Button with Delayed Egress Timer

4SECO-LARM U.S.A., Inc.

NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the

SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right

to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

or in part, without the written permission of SECO-LARM.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in

normal service for the life of the product from the date of sale to the original customer. SECO-LARM’s obligation is limited

to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This

Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair

or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that

such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole

obligation of SECO-LARM and the purchaser’s exclusive remedy shall be limited to the replacement or repair only, at

SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential

personal or property damage of any kind to the purchaser or anyone else.

SECO-LARM®U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA, 92606

Website: www.seco-larm.com

PITSW4

Tel: (949) 261-2999 | (800) 662-0800

Email: [email protected]

MiSD-7428-GSEQ_1310.docx

Order part # 763-178%

Remote Alarm Relay Output:

The SD-7428-GSEQ is equipped with a 3A@30VDC Form C dry relay output for a remote alarm.

The remote alarm relay is normally energized.

A remote device or alarm connected to this output will be triggered at the start of the

pre-delay timer.

The remote alarm output will continue signaling until the keyswitch is turned on momentarily.

In the event of power loss, the remote alarm relay will de-energize to trigger the remote alarm.

Troubleshooting:

Request-to-Exit Button will not

release the lock

Check the nuisance delay (see page 3)

Check the pre-delay timer (see page 3)

Door will not relock

Turn keyswitch to re-energize lock relay

IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of

this product complies with all national, state, and local laws and codes related to locking and egress devices.

SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.

Lock Relay Output:

The SD-7428-GSEQ is equipped with a 3A@30VDC Form C dry relay output that can be used

with a fail-safe lock.

The lock relay is normally energized.

The lock relay will de-energize after the pre-delay time expires. The lock relay will re-energize

once the keyswitch is turned on momentarily.

Indice

Altri manuali ENFORCER Serratura della porta

ENFORCER

ENFORCER SD-7104SGEX1Q Manuale utente

Manuali Serratura della porta popolari di altre marche

Assa Abloy

Assa Abloy effeff 827A-IP Manuale utente

We.lock

We.lock SECBNEBL51 Manuale utente

Iseo

Iseo MA1A Manuale utente

ID Lock

ID Lock 150 Manuale utente

Lockly

Lockly ACCESS TOUCH PRO Manuale utente

iLoq

iLoq G50S Manuale utente

SDC

SDC Z7835 Manuale utente

ilco

ilco 452 Manuale utente

Samsung

Samsung shs-h705 Manuale utente

TRU-BOLT

TRU-BOLT 08102017 Manuale utente

CDVI

CDVI 500-LADJ Manuale utente

Igloohome

Igloohome Deadbolt 2S Metal Grey Istruzioni di installazione e manutenzione

eSSL

eSSL FL-300 Manuale utente

JAKO

JAKO JKBTNX4 Manuale utente

Dorma

Dorma MUNDUS PREMIUM GK 50 Guida utente

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manuale utente

Yale

Yale MORTISE 8800 SERIES Manuale utente

Siegenia

Siegenia KFV AS3500 Manuale utente