ENFORCER EV-T5105-N2SQ Manuale utente
®
Wall-Plate Cameras
Manual
Features:
1
/
3.2
" 1.3MP Sony STARVIS CMOS
2.4mm Wide angle lens
Weatherproof construction
Vandal-resistant design
Adjustable mounting angle
Includes: 1 camera, 1 single-gang plate,
1 slimline plate, and angled mounting rings
2DNR (2D Digital Noise Reduction)
WDR (Wide Dynamic Range)
12VDC Operating voltage
Model # Lens Image Sensor Resolution Video Output Format
EV-5105-N1SQ 2.4mm
1
/
3.2
" 1.3MP Sony
STARVIS CMOS
1000TVL NTSC
EV-T5105-N2SQ 720p HD-TVI
ENFORCER Wall-Plate Cameras
2SECO-LARM U.S.A., Inc.
Dimensions:
S
p
ecifications:
Parts List:
1x Camera 1x
A
ngled rubber ring (EV-5105-N1SQ) 1x Slimline plate
2x Mounting screws 1x
A
ngled aluminum ring (EV-5105-N1SQ) 1x Single-gang plate
1x
A
luminum hex nut 2x
A
ngled aluminum rings (EV-T5105-N2SQ) 1x Manual
Model EV-5105-N1SQ EV-T5105-N2SQ
Type Wall-plate camera
Plate type 1 Single-gang, 1 slimline
Image sensor 1/3.2" 1.3MP Sony STARVIS CMOS
Resolution 1000 TV Lines 720p
Video output format NTSC HD-TVI
Effective pixels 1280x960
2DNR Yes
WDR Yes
960H* Yes No
Scanning system 2:1 Interface
Sync Internal
Video output 1.0Vp-p Composite video, 75Ω
Lens 2.4mm
Viewing angle 150°
FPS 30FPS
F Stop 2.2
Minimum illumination 0.001Lux
Gamma correction 0.45
S/N Ratio 120dB 50dB
Gain control Auto
Operating voltage 12VDC
Current draw 80mA 90mA
IP Rating IP67 IP65
Operating temperature -22°~176° F (-30°~80° C)
Dimensions
Camera 11/8"x11/8"x11/2" (28x28x38 mm) 11/8"x11/8"x17/8" (28x28x48 mm)
Single-gang plate 23/4"x41/2" (70x114 mm)
Slimline plate 11/2"x41/2" (38x114 mm)
23/4" (70mm)
Single-gang plate
*In order to take full advantage of 960H resolution, the camera must be used with a 960H DVR
11/2" (38mm)
Slimline plate
41/2"
(114mm)
Camera body
EV-T5105-N2SQ
11/8"
(28mm)
15/16"
(
24mm
)
17/8" (48mm)
11/4"
(32mm)
Camera body
EV-5105-N1SQ
11/8"
(28mm)
7/8"
(
22mm
)
11/2" (38mm)
7/8"
(22mm)
ENFORCER Wall-Plate Cameras
SECO-LARM U.S.A., Inc. 3
Overview:
Before Starting:
Mounting the Camera to the Plate: Mounting Options:
Changing the Mounting Angle:
1. Read this manual carefully and keep it for future
reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
4. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.
5. Do not open or disassemble the camera. There
are no user-serviceable parts inside.
6. Do not subject the camera to extreme shock.
Plate
Female BNC connector
DC Jac
k
Note polarity when connecting
To mount the camera to the plate, position the
angled rings behind the plate and twist the aluminum
hex nut on to secure the plate to the camera.
Install one of the angled rings on the front of the plate
so that the camera is tilted (approximately 20°).
If an object installed next to the camera on the wall
is blocking the field of vision, the angled rings may
be installed in front of the wall plate to move the
field of vision forward.
Mount directly to the back box (not included).
Drill a hole in the wall according to the diameter of
the camera body. Mount the plate directly to the wall.
Drill a hole in the wall according to the diameter of
the camera body. If mounting to a thick surface, it
may not be necessary to use the angled rings.
With Plate and Back Box (suggested):
Plate, no Back Box:
No Plate and no Back Box:
Back
box
Min. wall thickness: 5/16" (8mm)
Max. wall thickness:
EV-5105-N1SQ:
3/4" (20mm)
EV-T5105-N2SQ:
1 5/16" (34mm)
IMPORTANT: Do not cut the video or power wires
as warrant
y
will be voided.
Camera
A
ngled aluminum ring
A
ngled rubber/aluminum ring
NOTE: Ensure that the angled aluminum ring is installed next to the aluminum hex nut in all
applicable mounting installations.
When installing the camera, ensure that the white mark behind the lens is at the top.
A
luminum hex nut
ENFORCER Wall-Plate Cameras
4SECO-LARM U.S.A., Inc.
The screen is blank
Check that the camera is powered up
Check that the power supply's polarity is correct
Check that the monitor is powered up
Check that the video cable connecting the camera to the
monitor is connected properly
The screen image is dim Clean the lens using a soft, clean cloth
The screen image has poor contrast Adjust the monitor's contrast knob
Change the position of the camera
The screen image flickers Change the position of the camera
The screen image is distorted Change the position of the camera
The camera case is hot Check that the correct power supply is in use
4-in-1 HD Motorized
Rollerball Camera
4-in-1 HD Motorized
Bullet Camera
4-in-1 HD Motorized
Vandal Dome Camera
EV-Y2201-ANWQ EV-Y1201-ANWQ EV-Y2201-ANWAQ
Also Available from SECO-LARM®:
Troubleshooting:
SECO-LARM
® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Phone:
(
949
)
261-2999
|
(
800
)
662-0800 Email: sales
@
seco-larm.com
®PITSW1
Order Part# 764-100-7%
MI_EV-x5105-NxSQ_170816.doc
x
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2017 SECO-LARM U.S.A., Inc. All
rights reserved.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be
held responsible for the use of this product in violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Questo manuale è adatto per i seguenti modelli
1
Altri manuali ENFORCER Telecamera IP
