EnGenius ENH500 Manuale utente
1
EnGenius WDS Bridging Guide and Setup Example
There are three types of WDS Operation Mode and each of them serves the purposes as follows -
WDS Access Point (AP):
This mode allows you to simultaneously broadcast a publically visible WiFi network while bridging to
another WDS AP or WDS Bridge.
(Four other WDS AP/Bridge units can be linked back to one WDS Access Point using MAC address
assignment in the WDS Link Settings.)
WDS Bridge:
This mode is required if you want to create a point-to-point link that is not visible to the public.
(Four other WDS AP/Bridge units can be linked back to one WDS Bridge using MAC address assignment in
the WDS Link Settings. –It is also worth noting that WDS Bridge is the fastest of all WDS modes.)
WDS Station:
When using WDS Station the device is effectively like a Client Bridge but maintains the integrity of a WDS
link in terms MAC address transparency.
(You can connect as many WDS Stations to a WDS AP as you require because you do not rely on the WDS
Link Settings and simply do a Site Survey to connect to the WDS AP.)
WDS Bridge Setup Example
It is quite often that there is a requirement to deploy a wireless bridge between two buildings to share an
Internet or network connection and this requires the use of a pair of Outdoor WiFi units.
Here I will show you how to set up a generic scenario where a building-to-building link is required.
First of all we need to make a note of the Wireless MAC address of each unit –this can be located on the
label on the back and in the Main section from the Status heading.
For this demonstration we will have a Unit A and a Unit B set up in WDS Bridge Mode.
We will also assume that the Default Gateway/Router of the network has an IP address of 192.168.2.1
2
The default IP address of the EnGenius Outdoor WiFi unit is 192.168.1.1 (may vary according to model).
We need to ensure we’re on the same subnet as the EnGenius unit so give your computer’s Ethernet
adapter a temporary static IPv4 address of 192.168.1.20
1. After doing this connect your EnGenius unit to your computer, open a web browser, and in the
address bar type in 192.168.1.1 - click enter and you should see a log in box appear.
-Use “admin” for both Username and Password.
-Select Operation Mode from the menu heading System
-Select United Kingdom (or appropriate Country)
-Select WDS then Bridge
-Click Save & Apply
This will convert the unit’s mode of operation to a WDS Bridge.
3
2. Next go to the WDS Link Settings from the menu heading Wireless
- Set the Security to AES
- Enter an AES Passphrase at least 8 characters long (you will use the same passphrase on Unit B)
- Select Enable from the Mode box –this will allow you to enter a MAC Address of the other unit.
- Type in Mac Address of Unit B (next time we will do vice versa and use the MAC address of Unit A)
- Click Accept
(Be aware of Save/Reload: under the Status heading, you can apply multiple changes at once but
they won’t take effect until you click Save & Apply from this section, don’t do this just yet...)
3. Go to IP Settings from the menu heading System
-As the Router in the network has an address of 192.168.2.1 we need to give the Engenius unit an IP
address that is in the same network range but does not clash with anything else.
-Here I’ve used 192.168.2.100
-The Subnet Mask should be 255.255.255.0
-If desired, put in the Router’s address for the Default Gateway (our example is 192.168.2.1)
-Click Accept
4
4. Go to Save/Reload: under the Status heading and click Save & Apply.
-The unit will now be configured as we require but you will no longer be able to access it as the IP
address has been changed to a different subnet (the subnet of the router).
-Disconnect it from your computer however leave it powered up, as we will want to see if we can
establish a link after we’ve set up the second unit.
5. Now we will configure Unit B - connect it to the computer in the same manner as the last.
-Repeat step 1. In this guide.
-Repeat step 2. But type in the MAC Address of Unit A (use exactly the same passphrase as before)
-Repeat step 3. But give the unit an IP Address of 192.168.2.101 (So it doesn’t clash with the other)
-Repeat step 4. You should now see the unit configured as desired.
6. After the unit has rebooted we may have to change the IP Address of the computer to access it -
-If so we only need to change the subnet so alter the computer’s Ethernet IPv4 Settings from
192.168.1.20 to 192.168.2.20
-Use the web browser to log into the address 192.168.2.101 as before and go to WDS Link List
under the Status heading.
-Here we should be able to see the WDS Link Status and if the wireless bridge is up and running.
-So now both the units are configured, each with a static IP address that resides on the same
network as the router, finally we change our computer’s Ethernet settings back to Obtain an IP
address automatically / via DHCP.
There are many ways you can use WDS, however if you wanted a unit to broadcast a publically
visible WiFi Network we could set it (or multiples) up as a WDS AP for additional WiFi coverage.
Altri manuali per ENH500
8
Indice
Altri manuali EnGenius Hardware di rete
EnGenius
EnGenius Neutron Series Manuale utente
EnGenius
EnGenius IEEE 802.11b Outdoor Wireless Client Bridge Manuale utente
EnGenius
EnGenius X-TRA RANGE ERB300H Manuale utente
EnGenius
EnGenius ETA1305 Manuale utente
EnGenius
EnGenius EOA7530 Manuale utente
EnGenius
EnGenius EL-2611CB3+ Manuale utente
EnGenius
EnGenius ECB350 Manuale utente
EnGenius
EnGenius ECB9300 Manuale utente
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
