Enigma Motus Powered Manuale utente

Motus©Powered

Installation Guide

NFR Visible Trims

April 2022 | Revision B

SEL-PRT-00776

Thank you for choosing Enigma

To ensure the installation process is simple and ecient,

we recommended you read this guide in full rst.

Specic tools are also required to complete the installation:

Laser Level

Pencil Tape Measure Knife Cordless Drill Driver

Powered

Chop Saw

Hex Keys

(Metric)

Cable Stripper

& Cutters

Flathead Screwdrivers

(Medium & Small)

Long-nose

Pliers

——————— Sync Unit Wiring Tools ———————

For Double Doors

Getting started

The Motus Enigma pocket door system will be delivered in three boxes:

1. Pocket Frame

2. Trim Surround

3. Track

If a door leaf has been ordered this will come separately.

Before you start installation ensure you

have read and understood the instructions.

POWER REQUIREMENTS

DELIVERY

The Motus Enigma pocket door system requires a low-voltage electrical

connection. Wiring for the system can vary based on the type of connection:

Hardwired (Optional)

1. 13 amp fused spur isolation switch

2. 1.5mm twin and earth cable feed to the

top of the pocket enclosure

‘Kettle-lead’ Wiring (Standard)

1. 13 amp single socket

IMPORTANT SAFETY INFORMATION

The unit should be installed and commissioned by a trained and qualied personnel.

The unit may only be opened and repaired by the manufacturer.

This unit may only be operated from a protective low-voltage with safe electrical isolation.

Always consider the safety functions of your application as a whole, never just in relation to one individual component of the system.

The installed is responsible for carrying out a risk assessment and installing correctly.

Avoid touching any electronic components.

Motus Frame kit NFR V

MOTUS FRAME FIXINGS

MOTUS FRAME COMPONENTS

MOTUS NFR V › INSTALLATION GUIDE |FRAME KIT CONTENTS

Familiarise yourself with components included. All xings will

come pre-packaged to suit your specic project requirements.

Type-4

30mm screw

Type-5

25mm self drilling screw

Concrete Screws

7.5mm x 60mm

M6 Screws

6mm x 100mm

Timber Insert

Motus Sliding Track

Head Channel

Intermediate Jamb

Base Channel Leading Edge Jamb

Door Guide Pin & Channel

Type-2

40mm screw

Type-1

19mm self drilling pan head screw

Type-13

60mm screw

Type-3

50mm screw

Brush Strip

Base Channel Calculations

Please refer to Step 4 of the Frame Installation instructions shown on page 12.

Door sizes (mm)

Height = S/O -95mm

Clear

openings (mm)

Structural

openings (mm)

Wall construction preparation

The Motus Enigma system can be tted to steel or

timber studwork partitions. If using steel you must ensure

the head stud is strong enough to take the door weight.

IMPORTANT INSTALLATION NOTES

MOTUS NFR V › INSTALLATION GUIDE |WALL CONSTRUCTION PREPARATION

1. Studwork size

The studwork size required is 94mm.

If using steel studs a 94mm head and base track and

92mm uprights should be used.

2. Steel studs

If using steel studs, timber inserts are required within

the studs to provide additional strength and purchase

for 60mm track screws.

3. Doors above 2300mm

If the door height you are installing is above 2300mm

then using 2 layers of plasterboard is recommended.

To order kits to suite two layers of plasterboard add

the sux (145) to the product code.

4. Self-supporting Head

For situations in high rise buildings where you cannot

x to the ceiling or sot then use the Enigma Self-

supporting Head installation detail.

Follow standard Enigma instructions to calculate your

studwork structural opening and add the following

dimensions: Width +92mm and Height +44mm.

Refer to the specic Self-supporting Head installation

instructions for further details.

Width Single

Width Double

Height

1870

3700

Door +95mm

2120

4200

Door +95mm

2370

4700

Door +95mm

Width

Min. Height

Max. Height

Min. Single

Max. Single

Min. Double

Max. Double

875

1500

2815

600

844

1000

1710

845

969

1711

1960

970

1094

1961

2210

1000

1500

2815

1125

1500

2815

MOTUS TRACK SIZE

ITEM 1750mm 2000mm 2250mm

Dimensions

Motus NFR V

Bespoke requirements?

Enigma can be customised to suit bespoke projects.

In principle, the installation process remains the same,

however certain installation dimensions may dier.

Please contact the Selo team to discuss your bespoke

requirements.

020 3880 0339

SELF-SUPPORTING HEAD

Follow the standard Enigma instructions to calculate your studwork structural

opening and add the following dimensions: Width +92mm and Height +44mm

IMPORTANT

If installing Self-supporting Head please refer to the specic installation instructions for further details

When constructing your stud partition, please

ensure the head is strong enough to take the

weight of the sliding door that will hang from it.

IMPORTANT

If using a Self-supporting Head please refer to those

specic installation instructions.

CHECK SIZE WITH SCHEDULE

STRENGTHEN HEAD

When forming the structural opening, please

ensure you are working to the correct opening

size provided on the door schedule.

MOTUS NFR V › INSTALLATION GUIDE |WALL CONSTRUCTION PREPARATION 9

LEVEL-UP

Ensure the opening is square and plumb.

IMPORTANT

We strongly recommend using a laser level for setting out.

PREPARE HEAD CHANNEL & SLIDING TRACK

Single doors

Cut the head channel to S/O width.

Double doors

Cut the Head channels equally to take up the

whole S/O. It is important to ensure that where the

two channels meet is in the centre of the opening.

PREPARE THE STRIKE JAMB

IMPORTANT

If installing double doors skip this step.

Cut some C16 timber stud (70mm x 45mm)

to the height of the structural opening.

Cut noggins at 26mm thick. Space at a

maximum of 500mm centres and x to the

strike as per the drawing.

Using a laser level, t the head channel to the top

stud with Head Channel screws.

IMPORTANT

It is important to ensure the Head channel is level with no

bends or bows. If the top stud is not straight then pack the

head channel out with packers to maintain level.

Single doors

The 70mm gap and the kettle lead port should be

at the strike end of the pocket.

Double doors

For double ensure the kettle lead ports are facing

each other in the centre of the opening and with

100mm gap between the tracks.

FIT THE HEAD CHANNEL

MOTUS NFR V › INSTALLATION GUIDE |FRAME INSTALLATION

Single doors

2a Mark 50mm from the rear end of the Head

channel and 70mm from the strike/front end.

2b The kettle lead port is at the front of the track

and will be installed at the strike end of the pocket.

Place the Track on the Head channel and line-up

the kettle lead entry point with the 70mm mark.

Align the centre lines of the Track and the Head

channel together, pilot drill the screw holes.

Double doors

Mark 50mm from each end. The Tracks will be

installed with the kettle lead ports in the middle to

aid wiring. Place the two Head channels together

with the tracks inside lining up the centre lines.

Ensure there is 100mm gap between the tracks for

the wire box and then pilot drill the screw holes.

HEAD CHANNEL PREPARATION

70mm

Frame installation

IMPORTANT

If installing Self-supporting Head please refer to the specic installation instructions for further details

Cut the Leading edge jamb and

Intermediate jamb 15mm less than

the structural opening height.

FIT TOP TRACK

CUT LEADING EDGE & INTERMEDIATE JAMB

Cut the intermediate Timber insert 100mm

shorter than the aluminium jamb and slide the

insert into the Intermediate jamb so it sits

50mm from each end.

IMPORTANT

When using door leafs wider than 926mm the kit will

be supplied with extra intermediate jambs to be tted

equally space within the pocket width.

CUT & FIT INTERMEDIATE TIMBER INSERT

MOTUS NFR V › INSTALLATION GUIDE |FRAME INSTALLATION

The front of the track must be lined-up with the

70mm mark for single door, or 50mm mark for

double doors. (Detailed in Step 2)

Once in place, secure the Motus track to the

Head Channel using Type-13 screws provided.

Single/Double doors

To accurately determine the length of the Base

channel, refer to the calculations on the left.

Cut the Base channel to this dimension.

Do NOT cut-o the end with the notch. Image 4a

Base channel tting

Place the Base channel on the oor against the

rear stud.

If provided with a ‘cut-to-size’ system position the

notched end tight against the rear stud.

At this stage it is vital that to ensure that the

centre line of the Base channel is secured directly

underneath the centre line of the track above.

Any deviation will result in misaligned doors and

trims. Secure to the ground with Type-2 xings.

Cover-plate (Non- Sync)

If the Sync unit is not used, screw the cover-plate

provided between the tracks to cover the cable.

CALCULATE BASE CHANNEL & FIX

Structural opening examples*

1750mm wide

Single S/O 1820mm (Track +70mm)

Double S/O 3600mm (Track x2 +100mm)

Max. movement range 875mm

2000mm wide

Single S/O 2070mm (Track +70mm)

Double S/O 4100mm (Track x2 +100mm)

Max. movement range 1000mm

2250mm wide

Single S/O 2070mm (Track +70mm)

Double S/O 4100mm (Track x2 +100mm)

Max. movement range 1125mm

*S/O height Door leaf +95mm

Permitted door leaf sizes

Min. height 1500mm

Max. height 2815mm

Min. width 875mm

Max. width 1125mm

Travel for unit = The amount which goes into the strike jamb.

System calculations

Base channel length

Single doors NFR V

Structural Opening (minus) -Clear Opening (minus) -130mm

Double doors NFR V

Structural Opening (minus) -Clear Opening (minus) -64mm ÷2

9a Slide the Intermediate jamb into the

Head channel and Base channel with the

Timber inserts facing out so it sits centrally

in the pocket. Fix using Type-1 screws.

9b Slide the Leading edge jamb into Base

channel with notched end at the top, so the

ange sits hard against the end of the Base

channel. Plumb the jamb and x into place

using one Type-1 screw top and bottom as

shown in the image. Must be posited furthest

from the opening.

FIT POCKET SIDES & FIX THE JAMB

‘

MOTUS NFR V › INSTALLATION GUIDE |FRAME INSTALLATION 15

Single doors

Push the kettle lead in the strike end of the

track. Run the excess cable behind the strike

trim packer to the plug. DO NOT power on at

this point.

Double doors

Remove the kettle lead ports on both tracks.

As standard; Motus Double doors utilise a

Sync unit to open both doors at the same time,

additional wiring is required - See p18.

For Hardwired power supply please see p28.

CONNECTING THE TRACK

Cut the Brush Strip to length and t to the

leading edge aluminium prole.

IMPORTANT

If using simultaneous opening ensure that the door leafs

and head trims have been tted. Refer to the simultaneous

opening instructions for more.

FIT BRUSH STRIP

MOTUS NFR V › INSTALLATION GUIDE |DOOR LEAF INSTALLATION 17

4a The bracket ts onto the bolt as shown.

4b Feed the rest of the door at least halfway

into the pocket and hang the front bracket

onto the trolley bolt.

4c With spanners provided, wind the bolts up

or down to plumb the leading edge of the door

and to achieve the required gap under the

door (door undercut).

Tighten the locking nuts to secure the door to

the brackets. They may need to be slacked-o

later, to true the door to the trims once they

are tted.

HANG THE DOOR

4b 4c

Adjust the bolts to achieve a gap

approximately 15mm between the underside

of the track and the top of the bolt.

ASSEMBLE GEAR

The door leaf needs to be hung before the trim is tted.

FIT THE GUIDE CHANNEL

200mm

150mm

100mm

Apply a thin bead of adhesive into the groove in

the bottom of the door and then tap the plastic

channel into position.

Double Doors Fit brackets 100mm from the back edge and 200mm from the front so the two

doors meet in the centre over the 100mm sync unit. (Instead of hanging equally as per the singles.)

Single Door Position the brackets equally to the edges of the door, spaced to 150mm centres.

SINGLE

DOUBLE

FIT HEAD BRACKETS

150mm

Door leaf installation

MOTUS NFR V › INSTALLATION GUIDE |DOOR LEAF INSTALLATION 19

SYNC FOR DOUBLE DOORS ONLY

Slide the Door stop into the track, x into place

by tightening the grub screws. This can be nally

adjusted once the trims are installed. To set the

rear stop, slide the door back into the pocket

until the door will be ush with the leading edge

trims, then tighten the stop up against the

carriages.

IMPORTANT

It is important to set the rear stop at this point as once

plasterboard is installed there is no access to rear stop.

FIT THE DOOR STOPS

SYNC FOR DOUBLE DOORS ONLY

DRILL HEAD CHANNEL

REMOVE KETTLE-LEAD PORTS

IMPORTANT

The next steps A-E refer to the installation of a Sync unit

and is used with Double doors ONLY. For Single door

installation please skip the following steps.

Work out in relation to your current internal

wall cabling as to the route to the centre of the

tracks, then drill a hole no smaller than 8mm in

the Head Channel as shown.

Remove the fascias on both tracks to expose

the kettle lead port and connection terminals.

Ports need to be removed from both tracks.

Cut the Kettle-lead plug o the power cable

supplied and thread through the Head Channel

hole drilled previously.

Strip the cable approximately 30mm from the ends.

CONNECT TRACKS

WIRE POWER CABLE

PREPARE CABLE

SYNC FOR DOUBLE DOORS ONLY

Wire the block to the Tracks as shown.

Connect the two Tracks together with the

Sync-cable provided in the plugs shown.

Wire the power cable to the connector block as

shown then ‘power-up’ the track.

Indice

Altri manuali Enigma Riflettore

Enigma

Enigma TS-00028 Manuale utente

Enigma

Enigma TS-00047 Manuale utente

Manuali Riflettore popolari di altre marche

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Manuale utente

LIVARNO home

LIVARNO home 375304 2101 Istruzioni originali

Cameo

Cameo CLQS40WW Manuale utente

Leviton

Leviton Ellipsoid 5/50 Manuale utente

Monacor

Monacor img Stage Line PARL-56PDX/CR Manuale utente

Vector

Vector SL3AKV Manuale utente

Quantum

Quantum Q262 Manuale operativo

Philips

Philips Vari-lite VL3015LT Manuale utente

EUROSPOT

EUROSPOT C51 Manuale utente

DTS

DTS MINI BRICK ARC Manuale utente

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Manuale

ACME

ACME LED-MS350B Manuale utente

EuroLite

EuroLite Akku flat light 1 Manuale utente

Commercial Electric

Commercial Electric SPTM-1401 Manuale utente

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Manuale utente

Teknik

Teknik FLEXI Manuale utente

Craftsman

Craftsman CMXLSB10 Manuale utente

EuroLite

EuroLite LED SLS-144 UV Floor Spot Manuale utente