enlighted GW-2-00 Manuale utente
Page 4 -Installation Instructions 94-00040-01 94-00040-01 Installation Instructions -Page 1
Phone: 855.874.1691
Support: 866.828.859
support@enlightedinc.com
www.enlightedinc.com
Installation Instructions for Model:
GW-2-00
Installation Materials Supplied
•Gateway Unit
•Mounting Template
•2 x #6 - 1" screw
Tools you will need
•#2 Phillips Screw Driver
Additional Material you will need
•RJ45 Data Cable(s)
Caution
•Disconnect all power before
installation or service.
All installations and maintenance work
must be performed by qualified
personnel.
•The GW-2-00 must be installed in
accordance with state, local and
national electrical codes and
requirements.
enlighted Inc.
930 Benecia Ave.
Sunnyvale, CA 94085
www.enlightedinc.com
Page 2 -Installation Instructions 94-00040-01 94-00040-01 Installation Instructions -Page 3
Installation Instructions of the Gateway
1. The Gateway
should be located
within 300 feet of the
GEM unit and centrally
in the vicinity of the SU
Sensor Units.
2. Select a place in the
ceiling tile or wall for
the RJ45 data cable to
exit, and make a small
cut in the tile to
accommodate the
cable.
3. Install the Gateway
using the
Mounting Template
provided. Insert the 2
screws as stated in the
template into any
mounting surface.
4. Slide the Gateway Unit onto the screws as shown.
5. Route the RJ45 cable to the PoE Switch, and from the PoE switch to the
EM unit. Use good routing practices to avoid un-necessary interference
from other devices and electrical wiring.
Warning: This device complies with Part 15 of the FCC Rules and with Industry
Canada license exempt RSS Standards. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation. Changes or modifications not expressly approved by Enlighted
Inc. could void the user's authority to operate the equipment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at user’s expense.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Wiring Diagram
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio
peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur)
approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques
de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le
type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une
communication satisfaisante.
This radio transmitter IC:10138A-GW2 has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain and
required antenna impedance for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
Le présent émetteur radio IC:10138A-GW2 a été approuvé par Industrie Canada
pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal et l'impédance requise pour chaque type d'antenne. Les types
d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal
indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Antenna: Pasternack PE51081 Rubber Duck Dual Band: 2dBi, 50 Ohm.
FCC ID: AQQ-GW2
Indice
Altri manuali enlighted Portale
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
