ENMALAC ST9704V Manuale utente

ENMALAC™ST9704V 4-CHANNELH.264DVRMANUAL

Page ReservedbyReginexSendirianBerhad

User Manual

4-CHANNEL H.264 DVR

ENMALAC™ST9704V 4-CHANNELH.264DVRMANUAL

Page ReservedbyReginexSendirianBerhad

Warning

•To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

•All the safety and operating instructions must be read before the unit is operated.

Precaution

•Make sure to switch the power off before you install the DVR.

•Avoid using the DVR outside of the reference temperature and humidity indicated in the specification.

•Avoid exposing the DVR to violent movement or vibration.

•Do not use or store the DVR in direct sunlight or near to any source of heat.

•Do not place any object into the holes used for air circulation.

•Always use the DVR in the well ventilated location to prevent overheating.

•Do not disassemble or reassemble the product. It may cause malfunction or fire.

•There is the danger of an electric shock if DVR is repaired by an unqualified service engineer or installer.

Power Supply

•Please use the provided adaptor. The DVR provide DC12V,3A power adaptor. Please select the correct

voltage and power if using other adaptor.

•Keep the adaptor and power cord dry and protect from humidity.

•When this machine is not using for a long time, please remove the connection of power adaptor.

Features

•Non-pc stand-alone security digital video recorder with embedded operation system

•H.264 compression format

•Mobile monitoring

•Email for alarm

•Chinese/English languages supported

•Audio and video real time recording and playback

•Support NTSC/PAL video system

•4CH video inputs, 1CH BNC monitor output, VGA output

•4CH audio inputs, 1CH audio output

•High quality image, brightness, contrast and color adjustable for each channel

•Recording modes: manual recoding, always recording and scheduled recording include sensor alarm

recording and motion detection recording

•Multi Recording image quality

•CIF Audio/Video real-time playback, support D1, 1/2D1 resolution

•Searching modes: time & data searching, folder list searching, log list searching

•Support fast forward and fast rewind: ×2, ×4, ×8

•Backup modes: network backup, USB 2.0 backup, moveable USB HDD and USB DVRROM backup

•Support RS-485 PTZ control

•Support USB mouse operation

•Support 1 SATA port HDD.

•4 CH alarm input, 1 CH alarm output

•Multiplex operation: live & record & playback & network can be operated at the same time

•Support IE browser, email for alarm, DDNS function

•Network function: IE browser monitor/playback/record/backup/setup

ENMALAC™ST9704V 4-CHANNELH.264DVRMANUAL

Page ReservedbyReginexSendirianBerhad

Content

I INSTALLATION

1.1 Packing Detail

1.2 Front Panel Controls

1.3 Rear Panel Connectors

1.4 Rear Panel Connection

1.5 Remote Controller

1.6 Installation Process

II OPERATION

2.1 Power On

2.2 Power Off

2.3 Display Mode

2.4 Manual Recording

2.5 Alarm Recording

2.6 Schedule Recording

2.7 Playback

2.8 Time Searching Playback

2.9 Folder List Playback

2.10 Log List Playback

2.11 USB Backup

2.12 System Information

2.13 PTZ Control

2.14 Password

III SYSTEM MENU SETUP

3.1 Main menu

3.2 RECORD SEARCH

1. NORMAL SEARCHING

2. TIME SEARCHING

3. FOLDER LIST SEARCHING

4. LOG LIST SEARCHING

3.3 RECORD MODE

1. CHANNEL

2. RESOLUTION

3. QUALITY

4. AUDIO

5. RECORD MODE

6. FOLDER SIZE

7. DEFAULT

3.4 HDD MANAGEMENT

1. HDD LIST

2. OVERWRITE

3. FORMAT HDD

4. FORMAT USB

ENMALAC™ST9704V 4-CHANNELH.264DVRMANUAL

Page ReservedbyReginexSendirianBerhad

3.5 BASIC

1. LANGUAGE

2. TIME SETUP

3. PASSWORD

4. DISPLAY SETUP

5. VIDEO/AUDIO SETUP

6. EXIT

3.6 ADVANCE

1. ALARM

2. INFORMATION

3. MOTION DETECTION

4. MOBILE

5. MAINTENANCE

6. PTZ

7. NETWORK

IV IE BROWSER

4.1 USER LOGIN

4.2 RECORD SEARCH

4.3 LIVE

4.4 REPLAY

4.5 SETUP

V SPECIFICATION

ENMALAC™ST9704V 4-CHANNELH.264DVRMANUAL

I INSTALLATION

1.1 Packing Detail

1. DVR console x 1 unit

2. User’s manual x 1 unit

3. DC12V/3A power adaptor x 1 unit

4. Screws x 1 set

5. Infrared remote controller x 1 unit

6. USB mouse x 1unit

1.2 Front Panel Controls

1. ”UP” button

In the live display mode, press this button to display CH1. In the setup menu, press this button to move the

cursor up to the next line.

2. ”RIGHT” button

In the live display mode, press this button to display CH2. In the setup menu, press this button to move the

cursor in right direction.

3. ”DOWN” button

In the live display mode, press this button to display CH3. In the setup menu, press this button to move the

cursor down to the next line.

4. ”LEFT” button

In the live display mode, press this button to display CH4. In the setup menu, press this button to move the

cursor in left direction.

5. “ENTER” button

In the setup menu press this button to enter sub-menu or confirm setting.

6. “MODE” button

In the single channel display mode, press this button to change to QUAD display mode.

7. “MENU” button

In the live or record mode, press this button to enter main setup menu, press “ESC” button to quit menu.

8. “ESC” button

In the setup menu or PTZ operation mode, press this button to quit setup menu or PTZ operation mode.

9. “PTZ” control button

In the live or record mode, press this button to enter PTZ operation of single channel, press “ESC” button to

quit PTZ operation.

Page ReservedbyReginexSendirianBerhad

ENMALAC™ST9704V 4-CHANNELH.264DVRMANUAL

Page ReservedbyReginexSendirianBerhad

10. “REC” button

When set recoding mode to TIMER RECORD and set schedule recording mode to “OFF” or “ALARM” Mode,

press this button to start manual record, Press “STOP” button to stop manual record.

Note: When set recoding mode to POWER UP or ALWAYS, this button can not be used.

11. “PLAY” button

In the live or record mode, press this button to enter “RECORD SEARCH” menu. Press “UP”, “DOWN”, “LEFT”

or “RIGHT” button to select the playback setting and press “ENTER” button to play back. In the playback

mode, if it’s not in the playback, press this button to start playback.

12. “PAUSE” button

In the playback mode, press this button to pause the image, press it again for step forward the image.

13. “REWARD” button

In the display mode, repeat pressing this button to speed-up playback backward at the speed of 2x, 4x or 8x.

14. “FORWARD” button

In the display mode, repeat pressing this button to speed-up playback forward at the speed of 2x, 4x or 8x.

15. “STOP” button

In the manual record mode, press this button to stop the manual record.

16、USB 2.0 port

Connect with USB disk for updating firmware and backup files.

17、Mouse port

Connect with USB mouse. Not used for USB disk.

18. Receiver port of remote controller.

19. DVR indicator

POWER: ON when DVR power on.

HDD: Blink when backup from hard disk.

REC: ON during the DVR recording.

NET: Blink when network connected.

ALARM: ON when alarm signal detected (video loss, HDD loss, sensor alarm or motion alarm).

ENMALAC™ST9704V 4-CHANNELH.264DVRMANUAL

1.3 Rear Panel Connectors

1. CAMERA IN(CH1~CH4) 2. MONITOR OUT

3. AUDIO IN(CH1~CH4) 4. AUDIO OUT

5. RJ-45NET 6. VGA OUT

7. RS-485 PTZ 8. ALARM IN

9. DC: 12V/3A POWER IN 10. GROUND

11. DVR FAN

1.4 Rear Panel Connection

ALARM IN:

No. 1 ~ No. 4: Alarm signal input

No. 5: Alarm output: GND (Ground)

No. 6: Alarm output: N.C. (Normally Close)

No. 7: Alarm output: N.O. (Normally Open)

No. 8: Alarm output: COM (Common)

No. 9: RS-485 + (A)

No.10: RS-485 - (B)

Page ReservedbyReginexSendirianBerhad

ENMALAC™ST9704V 4-CHANNELH.264DVRMANUAL

1.5 Remote Controller

Remote Controller Introduction:

1. REC: Begin and stop manual recording.

2. PLAY: Enter the playback mode and display the RECORD SEARCH menu.

3. MENU: Display the MAIN setup menu in the live display mode.

4. UP: Press this button to move the cursor up to the next line in the setup menu.

5. ESC: Return to the previous mode in the setup menu.

6. RIGHT: Press this button to move the cursor in left direction in the setup menu.

7. ENTER: Enter in the setup menu.

8. RIGHT: Press this button to move the cursor in right direction in the setup menu.

9. STOP: In the manual record mode, press this button to stop the manual record.

10. DOWN: Press this button to move the cursor down to the next line in the setup menu.

11. PTZ: Enter PTZ operation mode.

12. PAUSE: Press this button to display a still picture during the playback, press this button again to step

forward the image.

13. REWARD: Repeat pressing this button to speed-up playback backward at the speed of X2, X4 or X8

during the playback.

14. FORWARD: Repeat pressing this button to speed-up playback forward at the speed of X2, X4 or X8

during the playback.

15. MUTE: Turn audio on/off during the live display mode or playback mode.

16. No.1: Display channel 1 picture on the monitor.

17. No.2: Display channel 2 picture on the monitor.

18. QUAD: Display quad picture on the monitor.

19. No.3: Display channel 3 picture on the monitor.

20. No.4: Display channel 4 picture on the monitor.

1.6 Installation Process

1. Turn off the power of DVR.

2. Open the top cover of the DVR and mount HDD with the screws. Connect power cord and SATA

cable between HDD and DVR main board. Then install the top cover.

3. Connect BNC for CAMERA IN port, MONITOR OUT port and JACK for AUDIO IN, AUDIO OUT port

from the relevant equipments.

4. Connect the power cord of adaptor.

Page ReservedbyReginexSendirianBerhad

ENMALAC™ST9704V 4-CHANNELH.264DVRMANUAL

Page ReservedbyReginexSendirianBerhad

II OPERATION

2.1 Power On

1. After installation correctly, connect power adaptor to switch the power of DVR on.

2. The HDD must be formatted by DVR when using the HDD first time.

2.2 Power Off

1. Remove the power adaptor cord. It’s better not to remove the power of DVR during recording,

playback or system setup.

2. If the DVR is not in use for a long time, please remove the connection of the power cord of adaptor.

2.3 Display Mode

1. Press the “MODE” button to display quad picture in the live display mode. Press “UP”, “DOWN”,

“LEFT” and “RIGHT” button to select single camera and the single live view is displaying on the

screen.

2. Use mouse double click the mouse to select single camera and the single live view is displaying on the

screen in the live display mode. Double click again to return back to display quad picture.

2.4 Manual Recording

1. Set recording mode to TIMER RECORD in the RECORD MODE menu. Set all channel and all date/time

to MANUAL REC mode in the SCHEDULE menu.

2. In the live mode, press the “REC” button on the front panel or remoter controller to start manual

recording. Or right click mouse and select MANUAL REC to start manual recording. A red symbol R will

be displayed on the picture of the channel. Press STOP button on the front panel or remoter

controller to stop manual recording. Or right click mouse and select STOP REC to stop manual

recording.

3. If the hard disk is full during recording, the system may stop recording when selecting OVERWRITE

to CLOSE in the HDD MANAGEMENT setup menu. The system may not stop recording and

automatically overwrite the oldest recorded file when selecting OVERWRITE to OPEN in the HDD

MANAGEMENT setup menu.

2.5 Alarm Recording

1. Stop manual recording.

2. Connect ALARM IN port of DVR with outside sensor alarm equipments.

3. Set recording mode to TIMER RECORD in the RECORD MODE menu. Set relevant channel and

date/time for ALARM REC mode in the SCHEDULE menu.

4. When a sensor alarm input signal or motion alarm is detected, the relevant single screen will begin

ALARM recording. The red symbol R and I will be displayed on the image of the channel for sensor

alarm recording. The red symbol R and M will be displayed on the image of the channel for motion

alarm recording. For this recording mode, the alarm setting and motion setting in the ALARM SETUP

and MOTION DETECT menu must be set up correctly.

ENMALAC™ST9704V 4-CHANNELH.264DVRMANUAL

2.6 Schedule Recording

1. Stop manual recording.

2. Make sure the current date and time are correct.

3. Set recording mode to TIMER RECORD in the RECORD MODE menu. Set relevant channel and

date/time for this mode in the SCHEDULE menu.

4. The system begins or stops schedule recording automatically according to the SCHEDULE setup.

2.7 Playback

1. Press “PLAY” button on the front panel or remote controller to display RECORD SEARCH menu in the

live display mode.

2. Press “UP”, “DOWN”, “LEFT” or “RIGHT” button on the front panel or remote controller to move the

cursor to RECORD FILE. Press “ENTER” button to select date. Press “ENTER” and “ESC” button to

change date and finish date setting.

3. Move the cursor to SEARCH button in the RECORD SEARCH menu and press “ENTER” button on the

front panel or remote controller to get detailed recording date and time.

4. Press “UP”, “DOWN”, “LEFT” or “RIGHT” button to select recording date and time, press “ENTER” to

play back.

Page ReservedbyReginexSendirianBerhad

Indice

Manuali Registratore digitale popolari di altre marche

FLIR

FLIR M3100E Series Manuale utente

VTRACKPRO

VTRACKPRO FPRO300 Manuale utente

Swann

Swann NVR-7085 models Manuale utente

XtendLan

XtendLan DVR-1670C Manuale utente

urmet domus

urmet domus 1093/004AHD Manuale utente

Holux

Holux M1 Manuale utente

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuale utente

Whistler

Whistler D16VRS Manuale utente

Defender Security

Defender Security 82-20235 Manuale utente

MISUMI

MISUMI MP-WF100M Manuale utente

Speco

Speco D8HU Manuale utente

UST

UST DDR-E04AA Istruzioni per l’uso

Consolidated

Consolidated Digital Video Recorder Manuale utente

Mace

Mace DVR0404RW Guida rapida

RCA

RCA RTD315W Manuale utente

FSM

FSM Colibri Grande PRO Manuale utente

Hauppauge

Hauppauge HD PVR 2 Manuale utente

Identivision

Identivision ICR-PH161i PIONEER Manuale utente