Enovation Controls MURPHY PowerView Manuale utente
00-02-1181
2019-10-12
Section 78
PowerView®
Model PV700
Installation Manual
In order to consistently bring you the highest quality, full-featured products, we reserve the right to change our
specifications and designs at any time. The latest version of this manual can be found at enovationcontrols.com.
Please read the following information before installing.
BEFORE BEGINNING INSTALLATION OF THIS MURPHY
PRODUCT:
Read and follow all installation instructions.
Please contact Enovation Controls immediately if you have any
questions.
This product can expose you to chemicals including lead, which is
known to the State of California to cause cancer. For more information,
go to www.P65Warnings.ca.gov.
Table of Contents
Hardware Installation .................................................................................................................... 3
Inspecting Package Contents.........................................................................................3
Surface-Mounted Installation..........................................................................................3
Preparing the Dash.....................................................................................................4
Surface-Mounting the Unit..........................................................................................4
Flush-Mounted Installation (Actual Size)........................................................................6
Flush-Mounting the Unit..............................................................................................7
Available Accessories for the PV700 .........................................................................7
Pinout Specifications ....................................................................................................................8
Standard Version.............................................................................................................8
Configuration Information..........................................................................................................11
Specifications ...............................................................................................................................12
Dimensions....................................................................................................................................13
THIS PAGE INTENTIONALLY LEFT BLANK
Hardware Installation
The following instructions will guide you through installing the PowerView display.
Inspecting Package Contents
Before attempting to install the product, it is recommended that you ensure all parts are
accounted for and inspect each item for damage (which sometimes occurs during shipping).
The items included in the box are:
•PV700 unit
•Installation manual web reference insert
Surface-Mounted Installation
Installation Kit –P/N 78051451 includes
•Mounting Bracket
•Gasket/Panel Seal
•Seven #8 washers
•Seven 8-32 machine screws
•Seven 10-32 nuts 3/8”
•Six 10-32 1-3/4” machine screws
Tools needed.
•Drill with 7/32 in. size bit
•Jigsaw
•Screw Driver
Preparing the Dash
Determine the location of the PV700 in the dash. Cut a hole in the dash to the
dimensions provided in the cutout templates.
Surface-Mounting the Unit
1. Place the back side of the display through the opening so the display will sit on the face
of the dash.
2. Use the included four long screws and locking nuts from the mounting kit (78051451) to
attach the unit to the bracket.
3. Torque to 10 inch-pounds.
Surface Mount (Actual Size)
Flush-Mounted Installation (Actual Size)
Flush-Mounting the Unit
1. Slide seal over display.
2. Slide the display through the cutout.
3. Fasten backing plate to the display using the 6 short 8-32 screws. Torque to 10 inch-
pounds.
4. Install the long 10-32 screws into the backing plate with locking nuts between the
display and the plate.
5. Hand-tighten the screws to draw the display tight against the panel.
6. Torque to 3 inch-pounds then tighten locking nuts.
Available Accessories for the PV700
The following PV700 accessories are available through Enovation Controls:
Part Number
Description
Order Details
78700667
PV700, Standard
Display
78090098
Programming Kit
Accessories
78051451
Kit, Mounting Bracket, PV700
78090069
Harness, PV750/PV700 Conversion, Power/CAN
Service
Pinout Specifications
Standard Version
Black Connector
1
Digital Input 1
2
Analog Input 3 +
3
Analog Input 2 +
4
Analog Input 1 +
5
CAN1 Low
6
CAN1 High
7
Battery
8
Ground
9
Analog Input 3 -
10
Analog Input 2 -
11
Analog Input 1 -
12
Digital Input 3
13
Digital Input 2
14
Frequency Output 1
15
Ignition On
16
N/A
17
N/A
18
CAN2 Low
19
CAN2 High
20
Digital Input 4
21
Digital Input 5
22
Digital Output
23
Frequency Output 2
Mating Connector
AMP 770680-1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Enovation Controls Monitor
Enovation Controls
Enovation Controls MURPHY PowerView PV500 Manuale utente
Enovation Controls
Enovation Controls MURPHY PowerView PV380-R3 Manuale utente
Enovation Controls
Enovation Controls Murphy PowerView PV485 Manuale utente
Enovation Controls
Enovation Controls Murphy PowerView PV485 Manuale utente
Enovation Controls
Enovation Controls Murphy PowerView PV101-C Manuale utente
Enovation Controls
Enovation Controls MURPHY PowerView PV1100 Manuale utente
Enovation Controls
Enovation Controls Murphy PowerView PV485 Manuale utente
