enphase Envoy-S Manuale utente
!
Getting Started Guide: Envoy-S Internet Connectivity All rights reserved. Enphase Energy © 2016
Getting Started Guide:
Envoy-S Internet Connectivity
This getting started guide is for the on-site
electrician or foreman who is responsible for
ensuring the Enphase Envoy-S™ is connected to
the Enphase Enlighten™ web monitoring system
before leaving the job site.
This guide applies to all Envoy models that look
like these:
Before You Start
Download the latest version of Enphase Installer
Toolkit™ before you leave the office. If you have
never logged into Toolkit, use your Enlighten
installer credentials to log in. This unlocks the
application for your ongoing use.
This step also ensures you have the latest
software upgrade package on your mobile device
in case you are directed to upgrade the Envoy-S in
the field.
Signs of Success!
When the Envoy-S is
connected to the Internet and
communicating with Enlighten,
the Network Communications LED (topmost) on
the Envoy lights solid green.
In addition, the Installer Toolkit
will verify that the Envoy is
connected and
communicating with
Enlighten.
Cellular Connectivity with Enphase Mobile
Connect
Complete the following steps
to install the Enphase Mobile
Connect™ modem:
1. Connect the cellular
antenna to the connector
labeled CELL on the
modem.
2. Mount the modem on a wall
using the slide-in-tab, or
attach the rubber feet and
mount on a flat surface.
If the Enphase AC Combiner
Box™ is installed, the
modem can sit on the bottom
of the box.
3. First, connect the USB cable to the USB port(s)
on the Envoy-S.
4. Then, connect the mini-USB connector to the
Mobile Connect modem.
The power LED lights when the modem has power.
After about two minutes, the Link Status (LS) LED
flashes to indicate a network connection.
• The Signal LEDs indicate signal strength
according to the Signal LED table below.
• Signal strength of 1 bar is adequate for data
transmission to Enlighten.
Within three minutes the Envoy-S Network
Communications LED lights solid
green, indicating a successful
connection to the Internet
and to Enlighten.
!
Getting Started Guide: Envoy-S Internet Connectivity All rights reserved. Enphase Energy © 2016
Wi-Fi Connection
There are two ways to configure the Wi-Fi
connection. Follow one of these methods to
connect the Envoy to the Internet and Enlighten.
Method A: Use the WPS function on the router.
1. Verify that there is no Ethernet cable connected
to the Envoy.
2. Confirm the homeowner’s router supports WPS
function. (WPS stands for Wi-Fi Protected
Setup.) Look for a button on the router with a
symbol like one of these.
3. Once you find WPS button on the wireless
router, press and hold it for a few seconds. On
most routers, a WPS LED begins flashing.
(Pressing the WPS button on the router
activates device pairing.)
4. Initiate the WPS
pairing at the Envoy
by pressing and
holding the AP
Mode button for five
seconds .
NOTE: If the AP Mode button is
held for fewer than five seconds,
AP mode will be initiated, but not
WPS pairing.
If AP mode is enabled
accidentally, the Envoy’s
network will be visible on your
Wi-Fi settings and the AP
Mode LED will be lit solid
green.
5. To disable AP mode, touch the AP Mode
button for one second, then release it.
Method B: Manually configure Wi-Fi connection.
1. Click on the Network tab.
2. Select the homeowner’s Wi-Fi
network from the list of available
networks.
3. Connect to the homeowner’s Wi-
Fi network. This may require that
you enter the homeowner’s
network password.
Within three minutes the Envoy-S
Network Communications LED
lights solid green to indicate
successful connection to the Internet
and to Enlighten.
Hard-Wire Ethernet
The most reliable Internet connection, when Mobile
Connect or Wi-Fi are not options, is a hard-wired
Ethernet connection. In a hard-wire connection you
must use an Ethernet cable (Use Cat5E or Cat6
UTP – Do not use STP cable) to connect to the
homeowner’s router on one end and directly to the
Envoy on the other end. This is a good option when
the Ethernet cable will span a distance of no more
than 100m (328 feet).
If it is not physically possible to hard-wire the
connection, use Ethernet bridges instead.
Envoy
Broadband
Router
!
Getting Started Guide: Envoy-S Internet Connectivity All rights reserved. Enphase Energy © 2016
Ethernet Connection Using Ethernet
Bridges
Use Ethernet bridges when the distance between
the Envoy and the router is too great, or when it is
impractical to span the distance between them with
Ethernet cable.
Complete the following steps to enable an Ethernet
connection using Ethernet bridges.
Bridge one:
1. Connect one end of the Ethernet “jumper”
cable to the bridge and the other end to the
Envoy.
2. If an AC Combiner Box is
installed, plug the bridge
into the outlet inside the
box and then connect the
cable to the Ethernet port
on the bottom of the
Envoy-S.
3. If you are not using an AC Combiner Box, plug
the bridge into a dedicated outlet near the
Envoy’s final install location and then connect
the cable to the Ethernet port on the bottom of
the Envoy-S.
Bridge two:
1. Connect one end of the Ethernet “jumper”
cable to the bridge and the other end to an
unused port on the router.
2. Plug the bridge into a dedicated
outlet near the router.
Within three minutes the Envoy-S Network
Communications LED lights solid green to indicate
a successful connection to the Internet
and to Enlighten.
When to Contact the Your Office
If you are unable to confirm the Envoy is
communicating with Enlighten, contact your
operations or installation support staff for
assistance.
Altri manuali per Envoy-S
2
Altri manuali enphase Portale
enphase
enphase ENV-S-WM230 Manuale utente
enphase
enphase COMMS-KIT-INT-02 Manuale utente
enphase
enphase CT-100-SPLIT ROW Manuale utente
enphase
enphase ENV-S-WM230 Manuale utente
enphase
enphase IQ Combiner 3C-ES Manuale utente
enphase
enphase IQ System Controller 2 Manuale utente
enphase
enphase ENV-S-AM1-120 Manuale di istruzioni
enphase
enphase CT-100-SPLIT ROW Manuale utente
enphase
enphase Envoy Communications Gateway Manuale utente
enphase
enphase IQ8D Manuale utente
enphase
enphase Envoy Communications Gateway Manuale utente
enphase
enphase Envoy Communications Gateway Manuale utente
enphase
enphase ENV-S-EM-230 Manuale utente
enphase
enphase Envoy-S Manuale utente
enphase
enphase Envoy Communications Gateway Manuale utente
enphase
enphase Envoy-S Standard ENV-S-WB-230-F Manuale utente
enphase
enphase Enphase Envoy-S Metered Manuale utente
enphase
enphase ENV-S-EM-230-LF-KIT Manuale utente
enphase
enphase Enphase Envoy-S Metered Manuale utente
enphase
enphase Gateway Manuale utente
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
