Enphase IQBattery 5 Manuale utente

QUICK INSTALL GUIDE (Model IQBATTERY-5P-1P-ROW)

Installing the IQ Battery 5

To install the Enphase IQ Battery 5 and the wall-mount bracket, read and follow all warnings and instructions in this guide. Safety warnings are listed at the

end of this guide. These instructions are not meant to be a complete explanation of how to design and install an energy storage system. All installations must

comply with national and local electrical codes and standards. 

The IQ Battery system includes the battery cellpack with integrated IQ Microinverters and battery management system (BMS). The system requires

IQ System Controller for grid-tied and backup operations. The IQ Gateway inside IQ System Controller measures PV production, IQ Battery charge/discharge

power and home energy consumption, and it senses when it is optimal to charge or discharge the battery so that energy is stored when it is abundant and

used when it is scarce.

https://enphase.com/trademark-usage-guidelines are trademarks of Enphase Energy, Inc. in the US and other countries.

Data subject to change. Rev 02

A. PREPARATION

A ) Make sure you have the following required Enphase items:

• One or more Enphase IQ Battery 5 and one IQ System Controller with

microgrid interconnect device (MID) functionality.

• The Enphase IQ Battery system requires an Internet connection

through the IQ Gateway in the IQ System Controller. Failure to maintain

an Internet connection may have an impact on the warranty.

See enphase.com/warranty for full terms.

• The IQ Battery and IQ System Controller are all connected to IQ

Gateway and communicate using communication control cables. The

Enphase PV system communicates to IQ Gateway using PLC.

B ) Make sure you also have the following required items:

• Mounting location that is structurally suited to bear the weight of the

IQ Battery. Total weight for the IQ Battery 5, including the IQ Battery

unit, cover, and wall-mount bracket, is 78.9 kg (174 lbs).

✓ NOTE: The wall must contain blocked studs that can bear the

battery weight or can be of masonry or other suitable structure.

• Tools: Conduit (with ttings and tting tools), drill, 4 mm pilot bit,

screwdriver, socket wrench, torque wrench, level, wire stripper, and

stud nder if installing on studs.

• Fasteners for wall-mount bracket and pedestal. Slots are 9.2 mm (0.36

in) for wall mount and 11.2 mm (inclined slots) for pedestal. Check with

a structural engineer and local standards for requirements.

• M8 lag bolts or screws: A minimum of three for single stud mounting and

four for dual stud mounting are required to mount the bracket on the wall.

• M6 screws: A minimum of two for single stud mounting and four for

dual stud mounting to fasten the top shield to the wall.

• Washers for use between fastener heads and wall-mount bracket.

• Copper conductors: 6 mm² to 30 mm² (11 mm (7/16 in) strip length)

copper conductors (rated at 90°C) for terminals.

• Control communications cables: Use Enphase recommended

cables, headers and also refer to local codes for any specic local

requirements.

• Conduit ttings: 20 mm, 25 mm or 32 mm (left and/or right side)

terminators are required for all installations, and IP55 conduit ttings

(terminators/raceway adapters) are needed when installing outdoors.

Enphase provides raceway adapters (sold separately) of varied lengths

as mentioned in later sections.

• Over current protection:The overcurrent protection in IQ Battery is not

branch circuit overcurrent protection and cannot be relied upon for

that purpose. The branch circuit overcurrent protection is located in IQ

System Controller or, when combining, in a separate combiner. See the

Enphase IQ System Controller Quick Install Guide for more information.

• Personal protective equipment (PPE) for handling lithium batteries as

required by local safety standards.

• Protective gloves for protection against sharp edges.

C ) Verify that main service is 230 V L-N.

✓ NOTE: The rated energy capacity of the battery is 4.96 kWh.

D ) Install the PV system and storage circuits into the IQ System Controller

as directed by the Enphase installation manuals.

B. UNBOXING THE IQ BATTERY 5

A ) Before you unbox the IQ Battery, check the “Energize By” label on the

shipping box to verify that the IQ Battery(ies) will be installed by the date

shown. If the date has passed, contact your distributor for next steps.

B ) Remove the upper packaging cover and follow the steps as shown in the

following image:

C ) Inspect the packaging and the IQ Battery(ies) for any signs of damage,

such as cracks, dents, or electrolyte leaks. Do not install or use the IQ

Battery(ies) if it has been dropped or damaged in any way. If damaged,

contact your distributor for replacement.

D ) Make sure your kit includes the following IQ Battery components:

• One IQ Battery 5

• One ID cover, two conduit covers

• One mounting bracket

• One top shield

*WARNING: Risk of injury. Take care when lifting. The IQ Battery unit is

heavy (66.25 kg/146.05 lbs) and requires two people to lift it.













Scheduled for Q2 2023 release

Plan a location for the IQ Batteries

The IQ Battery housing is IP55 rated and can be installed indoors or outdoors. The

terminal blocks accept copper conductors of 6 mm² to 30 mm².

A ) Following local standards: Choose a well-ventilated location where the

ambient temperature and humidity are within −20°C to 55°C (−4°F to 131°F)

and 5% to 95% RH, non-condensing, preferably out of direct sunlight. The

optimum ambient temperature range for installation location is 0ºC to

30ºC (32ºF to 86ºF). Provide smoke alarms in the residence in accordance

with building, re, and installation codes.

✓ NOTE: The IQ Battery location must be compliant to local standards

and regulations (AS/NZ5139).

B ) Make sure the mounting location can sustain the total weight of the IQ

Batteries and mounting bracket. Total weight for the IQ Battery 5, including

the IQ Battery unit, cover and wall-mount bracket, is 78.9 kg (174 lbs).

C ) Plan the mounting location to be at least 15 cm (6 in) off the ground and

from the ceiling. Keep the IQ Battery away from falling or moving objects,

including motor vehicles.

*WARNING: If mounted in the path of a motor vehicle, we recommend

a mounting height that is minimum 91 cm (36 in) above the oor.

✓ NOTE: Wherever local codes allow a smaller separation distance for

Energy Storage installations, the minimum spacing around

IQBattery 5 MUST be at least 15 cm (6 in) from the top, bottom, left,

and right side of the product.

D ) Select a location where the tilt from vertical is less than 5° as shown in the

following image:

E ) Make sure the mounting surface atness is within 2 mm between boundary

lines as shown in following image:

✓ NOTE: If the variation of the atness is more than 2 mm, the battery

might not properly sit on the wall-mount bracket through key holes.

Use spacers if the variation is more than 2 mm.

F ) Make sure there are no pipes or electrical wires where you plan to drill.

G ) Plan to maintain at least 914 mm (36 in) of clearance in front of each IQ

Battery.

H ) Consider the dimensions of the IQ Batteries, easy access, height, and

length of cable when selecting the location.

I ) Select a location where you can interconnect IQ Battery to the

IQ System Controller.

J ) Follow all local standards and regulations set forth by Distributed

Network Service Provider (DNSP).

K ) Up to four IQ Battery 5 units can be daisy chained on a single branch

circuit. IQ System Controller supports up to a maximum of

80 A breaker for IQ Battery connection circuit.

L ) The maximum conductor size for IQ Battery 5 is 30 mm² and the

maximum breaker rating with this conductor size is 80 A.

Prepare to install the wall-mount bracket

A ) Starting at installation position closest to the power source, mark a level

line on the wall as a guide.

* WARNING: Multiple risks. Make sure not to drill or attach into

electric wiring or pipes that are in the wall.

B ) The wall-mount bracket comes in two parts- bottom bracket that carries

the weight of the IQ Battery and the top shield that covers the back of the

IQ Battery.

Top shield

(28.8)

Side view

(49.86)

513.38 mm (20.21 in)

534 mm (21 in)

9.2 mm

Mounting slots

Base unit mounting

key holes

Inclined slots for

pedestal assembly

Locating features for

pedestal leg marked ‘L’

Ground contact flanges for top

shield

11.2

Approximate weight: 4.75 kg/10.47 lbs

The key slots highlighted are to mount the

base unit of IQ Battery 5 to the wall-mount

bracket and should not be used to mount the

wall-mount bracket to the wall



C. INSTALLATION

VERTICAL +5°INCLINATION -5°INCLINATION

IQ Battery5

Mounting surface should stay within indicated 2 mm gap between the boundary lines

Mounting surface flatness (across the unit installation height) shall be within 2 mm

IQ Battery 5

Mounting Surface

522mm (20.5 in)

461 mm (18.15 in)

2x groundcontact flangestoconnectwithbottom

wall-mount bracket

10xwallmountingholes marked ‘F’

2x embosseswithindentationmarks

to provideflexibilitytothe installers to

fixtop shield to thewooden wall

Side view

(15.7)

F1 F2 F3 F4

F5 F6

F7 F8

F10

C ) Position the mounting bracket on the wall and fasten it using the

mounting slots:

D ) Position the ground contact ange of the top shield on that of the

mounting bracket and align the screw slot/hole.

E ) Fasten the top shield to the wall using the mounting holes shown below.

F ) Fasten top shield to the mounting bracket at the ground contact ange

using two M4 screws (torque to 1.5 N m) to complete the assembly.

G ) Use M8 screws/lag bolts (or masonry attachments for masonry wall)

to attach the bracket using one screw/lag bolt and washer for each slot

(9.2 mm/0.36 in). Use minimum of three screws/lag bolts for single stud

mounting and four screws/lag bolts for dual stud mounting. Tighten all

screws to manufacturer’s specied torque values.

H ) Make sure the wall-mount bracket is solidly attached to the wall.

I ) Use minimum two M6 screws for single stud mounting and four M6

screws for dual stud mounting to fasten the top shield to the wall.

* WARNING: Risk of injury and equipment damage. Do not mount an

IQ Battery 5 on a bracket that is not properly mounted.

Prepare to install IQ Battery on mounting bracket

A) Remove the ID cover from the packaging and keep it aside.

B ) Use the lifting handles (sold separately) and check that the plungers are

extended and ready to engage into the IQ Battery 5 slots.

C ) Align left handle on left side of the IQ Battery 5 and insert it into the slots

and slide towards the top of the IQ Battery 5 enclosure until it clicks into

place. Check that the handle is secure.

D ) Repeat on the other side with the right handle.

* WARNING:

• Risk of injury and equipment damage. Two persons are required to lift

the IQ Battery 5.

• Lift the IQ Battery from the packaging using the handles and make sure

the battery’s front side is facing towards you.

E ) Two persons together must lift the IQ Battery 5 unit from the packaging

using the handles and place it in upright position on a at surface.

F ) The IQ Battery 5 can have the eld cable entry from back, left, or right side.

Finalize the side from where the eld cable enters and leaves the IQ Battery 5.

Use the following conguration image to decide the cut-out for all the units.

+ DANGER Risk of electric shock. The DC control switch must be in the

OFF position before performing this step.

✓ NOTE: The rear entry can support the conduit with diameter of 1/2 in

(13 mm) to 3/4 in (19 mm) while side entry can support the conduit with

diameter of 1/2 in (13 mm) to 1-1/4 in (32 mm). Follow manufacturer

recommended instructions for conduit installation.

* One side conduit conguration is supported only if system has only one

IQ Battery or for the unit last in the daisy chain farthest from the

IQ System Controller.

450 mm stud spacing Single stud

1. Insert

Position theHandleTubebolt

concentrictothe keyholeslots in the

backplate and insert the handle

2. Slide

Slidetillplunger locks

to holeinbackplate

LH RH

HandleTubebolt

Wall-mount sub assembly

(Wall-mount bracket + top shield)

Ground contact flange

of top shield

Ground contact flange

of wall-mount bracket

Tightening

direction

2x M4 grounding screws

(Torque to 1.5 N m)











G ) Open the front wiring cover by unfastening the 11 captive screws (torque

to 1.5 N m) from the wiring cover. Use electric drive; do not use impact

drives/impact drills.

H ) Drill the appropriate cutout on either the back or side of the unit or on

both based on congurations. The rear entry can support the conduit

with diameter of 1/2 in (13 mm) to 3/4 in (19 mm) while side entry can

support the conduit with diameter of 1/2 in (13 mm) to 1-1/4 in (32

mm). Use the table to decide the cutout diameter and the conductor size

required for line, neutral, and ground.

IQ Battery installa-



Recommended

wire mm2





> 60 cm (24 in)





L & N GND W/CTRL* W/CTRL*

Single unit 6 mm210 mm220 mm conduit 20 mm conduit

2 units daisy chaining 10 mm210 mm220 mm conduit 20 mm conduit

3 units daisy chaining 25 mm210 mm225 mm conduit 20 mm conduit

4 units daisy chaining 25 mm210 mm225 mm conduit 25 mm conduit

* Calculations based on Enphase recommended control communication cables (CTRL)

with outside diameter ≤ 10 mm

* WARNING: Ensure that drilling machine do not touch any internal

components or wall.

* WARNING: Ensure to clean the debris from inside the battery unit after

drilling.

I ) Bring the IQ Battery 5 unit to the already mounted wall-mount bracket.

J ) Hold the IQ Battery straight, align, and insert 4 mount bolts on the battery

unit into the mounting bracket key holes and slide it down.

K ) Remove installation handles.

L ) Secure the battery unit on the wall-mount bracket using two seismic screws

(torque to 5.6 N m).

Prepare for eld wiring

A ) Connect the following connectors to the BMS board in following sequence:

i. B3: Temperature sense connector termination

ii. B4: Battery Voltage sense connector termination

iii. B1: Battery DC +ve connector termination

iv. B2: Battery DC -ve connector termination

v. CS1: Control switch intermediate connector termination*

* The control switch cable is secured to wiring cover using cable ties. Cut the cable ties

on the wiring cover to access the control switch cable.

✓ NOTE: Ensure that all the connectors are latched properly and clicking

sound is observed.

B ) Fasten (torque to 1.5 N m) the 11 captive screws at the wiring cover as

shown. Use electric drive; do not use impact drives/impact drills.

3. Pull

Pull thehandleaway

from theunitto

remove it

1. Pull

Pull theplunger

outwardstounlockthe

handle

2. Slide

Slidethe

handle down

2x Seismic screws











* WARNING: The vent or drain holes

provided at the back of the unit

serves the dual purpose of natural

ventilation and condensation

drainage. Blocking these holes

can affect the functionality of the

product.

Install conduit/raceway adapters and eld wiring

A ) When installing a single IQ Battery unit, insert the conduit in the cutouts

drilled in previous step.

✓ NOTE: Use a “chase nipple” & “rigid coupling” as spacer for

connecting 90° tting to the battery. This avoids interference

between the 90° tting and battery ID cover. Make sure the joints

are properly fastened and are watertight.

B ) If installing more than one IQ Battery, insert the conduit on the side of the

unit closest to AC disconnect. If an IQ System Controller is in line-of-sight,

the breaker on IQ System Controller can service as AC disconnect.

C ) Use either raceway adapter or conduit in between the IQ Battery units

based on following:

• Use conduit between units if distance between units is > 165 mm (6.5

in).

• Use raceway adapter between units only if the distance between units

is ≤ 165 mm (6.5 in) and are at the same level. Raceway adapters

can be provided by Enphase (sold separately) and has the following

conguration:





Corrected raceway







165 mm (6.5 in) 220 mm (8.6 in) 181.1 mm (7.13 in)

152 mm (6.0 in) 220 mm (8.6 in) 168.4 mm (6.63 in)

146 mm (5.75 in) 220 mm (8.6 in) 162.05 mm (6.38 in)

D ) Starting from the unit closest to IQ System Controller, pass the power

and control communication conductors through the conduit and make

the ends of conductors available on the unit and IQ System Controller

side.

E ) Connect the power conductors and control communication cables on the

terminal blocks (L, N, and Ground) and control communication connector

respectively. Each terminal block accepts 6 mm² to 30 mm² conductors.

Tighten L and N terminals to 2.5 N m (27 lb-in) and small Ground terminal

to 1.5 N m (13.2 lb-in).

✓ NOTE: Do not disturb the factory termination connections on

terminal blocks during eld wiring.

F ) If connecting more than one IQ Battery, connect power conductors be-

tween terminal blocks and control communication cables between CTRL

connectors of these units such that conductors connect on right side

of one unit and left side of another unit after passing through conduit or

raceway adapters. Repeat these steps until you arrive at the unit that is

farthest from the IQ System Controller.

✓ NOTE: Power and control communication cables will run in parallel

through conduits and raceway adapters.

G ) Follow jacket stripping length and connect the control communication

wires to 4-pin connectors as shown in the following image. Remove the

resistor from control connectors from all the units except the one farthest

from IQ System Controller in the daisy chain.

H) Route the conductors between conduit and terminal blocks using anchor-

ing points as shown in the following gure:

* WARNING: Make sure the drain wires do not come in contact with any live

connection.

I ) After all wires in the eld wiring compartment are connected and secured,

make sure there are no exposed conductors.

J ) Make sure the IQ Battery unit that is farthest from IQ System Controller has

a cutout only on one side and all other sides are covered.

K ) Apply AC power to the IQ Battery circuits. Using a voltmeter, make sure

voltage between L and N on the terminal blocks of each

IQ Battery unit measures 230 VAC (208-253 V).

L ) If the voltage is within the range as required by local codes, turn off the AC

power supply.

Ground

CTRL (shown in a different

color for distinction)

Ground

CTRL

From IQ System

Controller or IQ



To IQ Battery



Controller





Terminated with

resistor for last



chain

Termination resistor

on control connector





✓ NOTE: Drain wire should be terminat-

ed only at one SHIELD connector while

the other SHIELD connector shall remain

unconnected within each IQ Battery.

Cover and energize the system

*WARNING: Before energizing, make sure that ALL IQ Batteries in the

system are properly installed and conductors terminated.

* WARNING: Risk of equipment damage. Make sure no wires are

pinched before replacing the cover.

A ) Make sure the wiring cover(s) for all IQ Batteries in the system are closed

and secured.

✓ NOTE: Ensure the serial number label on the ID cover matches with

that on the heatsink before assembling ID cover.

B ) Slide on the IQ Battery cover in the indicated direction such that the tab

of the cover in the highlighted region rests and slides on feature in the

IQ Battery 5 chassis.

C ) Before releasing, pull out the lower edges while sliding in the cover and

make sure the tabs are locked to the back plate as shown in the following

gure:

D ) Push in the top portion of the cover as shown and make sure that the

cover is locked in place as indicated.

E ) Fasten cover to the extension backplate using two M5 Phillips hex head

screws (Torque to 3.1 N m)

F ) If the spacing ‘A’ between the units is < 165 mm (6.5 in), screwdriver

of maximum length 150 mm should be used to fasten cover to the

extension backplate.

✓ NOTE:The screw is accessible at 40° to the wall.

G ) After installing the cover,

• If the conduit terminator is installed, the conduit cover is not necessary.

• If the conduit terminator is not installed, then the conduit cover should

be installed to cover the opening in the IQ Battery cover on the other

side.

H ) Apply AC power to the IQ Battery circuits.

I ) Turn ON the DC control switch. A green LED will glow around the control

switch. The IQ Battery is ready for commissioning.

*WARNING: Do not leave the DC control Switch in ON position without

AC power supply available. This will deplete the battery and may lead to

a condition where battery cannot be turned ON and cannot be commis-

sioned.

Before step DAfterstepD

2x (M5x 10),Phillips hex head

40°

Battery serial



7Disassembly of the IQ Battery cover

A ) Remove the conduit covers from both sides of the IQ Battery cover.

Conduitcovers

B ) Remove the two M5 Phillips hex head screws (torque to 3.1 N m) which

are used to afx the cover to the extension backplate.

C ) Using the hand access slot, pull the top plastic grill slightly in the direction

shown below.

D ) Unlock the top plastic cover from the ribs highlighted in yellow.

E ) Make sure the cover reaches the position shown in the side view image

after the completion of this step.

F ) Pull out the lower portion of the cover (in order to unlock the highlighted

angular tabs) and move it away from the wall slightly as per the directions

shown the following gure. (back view).

Hand access slot

Before Step CAfterStepC



After step EBefore step E

Hand access slot



Before step 2Afterstep2



After step CBefore step C

G ) Make sure the cover reaches the position shown in the front view.

H ) Pull the cover off in the indicated direction.

State Description

Uncommissioned

Flashing blue After booting up, IQ Battery has paired with an

IQ Gateway but has not passed the commissioning three-

way handshake to conrm that it is an Enphase device.

Flashing green After passing the three-way handshake with the

IQ Gateway.



Rapidly ashing yellow Starting up/establishing communications

Red double ash Error. See “Troubleshooting”.

Solid yellow Not operating due to high temperature. See “Troubleshoot-

ing”.

Solid blue or green Idle. Color transitions from blue to green as state of charge

increases. Check Enphase Installer Platform for charge

status.

Soft pulse blue Discharging

Soft pulse green Charging

Soft pulse yellow Sleep mode

Red triple ash DC switch OFF

Red one-second ash Rapid Shutdown mode

Off Not operating. See “Troubleshooting”.

Operating mode and set points

IQ Battery supports multiple storage interactive system modes based on

usage.

A ) Using Enphase App, select “Menu” > “Settings” > “Battery Storage”.

B ) Select one of three battery modes:

• Self-consumption mode (default, no setting change required)

• Savings mode

• Full backup

For more information on Operation modes, refer to the Storage System Own-

er’s guide at https://enphase.com/en-au.

Troubleshooting

If the IQ Battery(ies) are not operating correctly, do the following. If the issue

persists, contact Enphase at https://enphase.com/en-au/support/contact.

A ) If the IQ Battery(ies) do not operate, check the temperature in the room and

increase cooling and/or ventilation as required. Check that the bottom, top

and sides of the IQ Battery 5 have at least 15 cm (6 in) clearance from

the wall.

B ) If the IQ Battery LED is off, turn off the breaker for the branch circuit, wait for

at least one minute, and turn it back on.

✓ NOTE: IQ Battery has multiple eld replaceable parts. These must be

replaced by trained service personnel. Contact Enphase Customer Support

before replacing any part.

✓ NOTE: During a brownout or blackout, the IQ Battery powers down auto

matically. This is normal. When power is restored, it automatically starts up

again.

C ) If you do not see IQ Battery information in Enphase App, check that the

IQ Gateway and the Internet connection are working. If the issue persists,

contact Enphase Customer Support at

https://enphase.com/en-au/support.

A ) Use the Enphase Installer App to commission the IQ Battery(ies). Once

connected to the IQ Gateway Metered, refer to the Enphase Installer App

help topics for more information.

B ) After the IQ Gateway Metered has detected the IQ Battery(ies), the IQ

Battery LEDs operate as described in the following section.

D. CONFIGURE AND ACTIVATE

E. OPERATION

aLED overview

After being commissioned, the LED ashes yellow while each IQ Battery

boots up. If the LED rapidly ashes green for more than two minutes,

the battery is in trickle charge mode and will remain so until it reaches a

minimum state of charge (up to 30 minutes). After the IQ Battery is booted

up, the LED becomes blue or green depending on the charge level. If the

LED ashes yellow after one hour or changes to a ashing red state, contact

Enphase Customer Support at https://enphase.com/contact/support

Limitation of Use:

Your IQ Battery unit is not intended for use as a primary or backup power

source for life-support systems, other medical equipment, or any other use

where product failure could lead to injury, loss of life, or catastrophic prop-

erty damage. Enphase disclaims any and all liability arising out of any such

use of your IQ Battery unit. Further, Enphase reserves the right to refuse to

provide support in connection with any such use and disclaims any and all

liability arising out of Enphase’s provision of, or refusal to provide, support

for your IQ Battery device in such circumstances.

A ) Isolate the AC power by de-energizing the AC power supply to the IQ Batteries.

B ) Using a multimeter, conrm that there is no AC power present.

C) Ensure the DC switch is in the OFF position using the following steps:

• If the IQ Battery LED is OFF, the DC switch is in OFF position and the

IQ Battery is in shutdown mode.

• If the IQ Battery LED (any color) is ON, press the DC switch once to

turn it OFF and place the IQ Battery in shutdown mode.

F. SHUTDOWN PROCEDURE

Enphase Customer Support: https://enphase.com/contact/support

Safety and Advisory Symbols

+DANGER: This indicates a hazardous situation, which if not avoided, will result in

death or serious injury.

*WARNING: This indicates a situation where failure to follow instructions may be a

safety hazard or cause equipment malfunction. Use extreme caution and follow

instructions carefully.

✓NOTE: This indicates information particularly important for optimal system operation.

Follow instructions carefully.

Safety Instructions

+DANGER: Risk of electric shock. Risk of re. Only qualied electricians should install,

troubleshoot, or replace the IQ Battery(ies).

+DANGER: Risk of re or explosion. Only qualied personnel, using personal protective

equipment (PPE) should transport or handle the IQ Battery(ies).

+DANGER: Risk of explosion. Do not dispose of IQ Battery(ies) in a re or by burning.

The IQ Battery(ies) can explode.

+DANGER: Risk of re or explosion. This product is designed for stationary installation

only and should be used accordingly. It is not designed for mobile applications

such as installation and on vehicles and trailers and should not be used in such

applications.

+DANGER: Risk of re. During use, when stored, or during transport, keep the IQ

Battery(ies) in an area that is well ventilated and protected from the elements, where

the ambient temperature and humidity are within -20° C to 55° C (-4° F to 131° F) and

5% to 95% RH, non-condensing, preferably out of direct sunlight. Do not install the IQ

Battery(ies) at elevations over 2,000 m (6,562 feet) above sea level.

+DANGER: Risk of re. If the IQ Battery(ies) generate smoke, remove AC power from

the Enphase System and turn the DC connect switch to the off position so that charg-

ing/discharging stops.

+DANGER: Risk of electric shock. Do not use Enphase equipment in a manner not

specied by the manufacturer. Doing so may cause death or injury to persons, or

damage to equipment.

+DANGER: Risk of electric shock. Do not install the IQ Battery(ies) without rst remov-

ing AC power from the photovoltaic system. Disconnect the power coming from the

photovoltaics before servicing or installing.

+DANGER: Risk of electric shock. Always de-energize the AC branch circuit during an

emergency and/or before servicing the IQ Battery(ies).

+DANGER: Risk of electric shock. Risk of high short-circuit current. Observe the follow-

ing precautions when working on batteries:

• Remove watches, rings, or other metal objects.

• Use tools with insulated handles.

• Wear insulating gloves and boots.

• Do not lay tools or metal parts on top of batteries.

+DANGER: Risk of electric shock. Risk of re. Do not work alone. Someone should be

in the range of your voice or close enough to come to your aid when you work with or

near electrical equipment.

+DANGER: Risk of re. Do not allow or place ammable, sparking, or explosive items

near the IQ Battery(ies).

+DANGER: Risk of electric shock. In areas where ooding is possible, install the IQ

Battery(ies) at a height that prevents water ingress.

+DANGER: Risk of electric shock. AC voltage is present at the output when the DC

switch is on.

+DANGER: Risk of electric shock. Branch circuit protection must be off before switch-

ing DC power on or off.

+DANGER: Risk of electric shock. The DC switch must be in the OFF position for

shipping and service.

*WARNING: Risks of electric shock, energy hazard, and chemical hazard. Do not

disassemble.

*WARNING: Risk of equipment damage. During use, storage, transport, or installation,

always keep the IQ Battery(ies) in an upright position.

*WARNING: You must install the IQ Battery(ies) only on a suitable wall using an

Enphase wall-mount bracket.

*WARNING: Before installing or using the IQ Battery(ies), read all instructions and

cautionary markings in this guide and on the equipment.

*WARNING: Do not install or use the IQ Battery(ies) if it has been damaged in any way.

*WARNING: Do not exceed the maximum number (1) of IQ Batteries in a 20 A AC

branch circuit.

*WARNING: Do not sit on, step on, place objects on, or insert objects into the IQ

Battery(ies).

*WARNING: Do not place beverages or liquid containers on top of the IQ Battery(ies). Do

not expose the IQ Battery(ies) to liquids or ooding.

*WARNING: When placing the IQ Battery(ies) in storage, ensure to follow the shut-

down procedure and conrm that AC power is not present and the DC switch is in the

OFF position. While in storage, damage to the battery can occur from over-discharge.

If the battery state of charge falls to 0%, the IQ Battery(ies) can be damaged or de-

stroyed. Because of this, the IQ Battery(ies) must only be stored for a limited amount

of time.

• The IQ Battery(ies) must be installed and energized by the “Must

Energize By” date on the shipping box label.

• The IQ Battery(ies) must have a charge state of no more than 30%

when placed in storage. To do this, the IQ Battery(ies) must be placed

in Sleep Mode.

• If the IQ Battery(ies) is already been installed, it must be placed

into Sleep Mode prior to uninstalling. A battery in Sleep Mode can be

stored a maximum of two months after being placed into Sleep Mode.

✓NOTE: Perform installation and wiring, including protection against lightning and

resulting voltage surge, in accordance with all applicable local electrical codes and

standards.

✓NOTE: Using unapproved attachments or accessories could result in damage or

injury.

✓NOTE: Install properly rated over current protection as part of the system installation.

✓NOTE: To ensure optimal reliability and to meet warranty requirements, the IQ Bat-

tery(ies) must be installed and/or stored according to the instructions in this guide.

✓NOTE: The Enphase IQ Battery(ies) are intended to operate with an Internet connec-

tion. Failure to maintain an Internet connection may have an impact on the warranty.

See Limited Warranty for full terms and services (enphase.com/warranty).

✓NOTE: When replacing Enphase IQ Battery(ies), you must replace with an IQ Bat-

tery(ies) of the same type, with the same AC current rating.

✓NOTE: When disconnected and stored, no automatic charge of the battery is

possible.

✓NOTE: Properly mount the IQ Battery(ies). Ensure that the mounting location is struc-

turally suited to bearing the weight of the IQ Battery(ies).

✓NOTE: During use, storage, and transport, keep the IQ Battery(ies):

• Properly ventilated

• Away from water, other liquids, heat, sparks, and direct sunlight

• Away from excessive dust, corrosive and explosive gases like ammonia,

and oil smoke

• Away from direct exposure to gas exhaust, such as from motor vehicles

• Free of vibrations

• Away from falling or moving objects, including motor vehicles. If mounted

in the path of a motor vehicle, we recommend a 91 cm (36 in)

minimum mounting height

• At an elevation of lower than 2,000 m (6,562 feet) above sea-level

• In a location compliant with re safety regulations

• In a location compliant with local building codes and standards

✓NOTE: Conditions for the IQ Battery installation site apply also to storage conditions.

SAFETY

IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This guide contains important instructions that you must follow during installation

and maintenance of the Enphase IQ Battery(ies). Failing to follow any of these instructions may void the warranty (enphase.com/warranty). Refer to

MSDS document and Safety Datasheet at https://enphase.com/en-au

In Case of Fire or Other Emergency

In all cases:

• If safe to do so, switch off the AC breaker for the IQ Battery circuit, and if an isolator

switch is present, switch off the AC isolator for the IQ Battery circuit.

• Contact the re department or other required emergency response team.

• Evacuate the area.



•

When safe, use a re extinguisher. Suitable types are A, B, and C dry chemical re

extinguishers. Additional extinguishing media include carbon dioxide, or alcohol-resis-

tant foams.



• Stay out of the water if any part of the IQ Battery(ies) or wiring is submerged.

• If possible, protect the system by nding and stopping the source of the water, and

pumping it away.

• If water has contacted the battery, call your installer to arrange a inspection. If you are

sure that water has never contacted the battery, let the area dry completely before use.



• Ensure nothing is in contact with the IQ Battery(ies) or in the venting area of the IQ

Battery(ies).

• Ventilate the room.

• Contact Enphase Customer Support at https://enphase.com/contact/support



The Enphase IQ Battery has a lithium iron phosphate (LFP) battery that contains organic

electrolyte and is sealed in a protective case. Leaked electrolyte is toxic and highly

ammable. Leaked electrolyte is colorless and has a sweet odor. Electrolyte uid tends to

evaporate quickly, leaving behind a white grainy substance. If an odor is obvious, proceed

to the following steps:

• DO NOT TOUCH OR INGEST ANY LIQUID SUSPECTED TO BE BATTERY ELECROLYTE.

• Evacuate personnel to a safe area and keep unauthorized personnel away.

• Isolate spill area to a minimum distance of 75 feet (25 meters).

• Eliminate all ignition sources (no smoking, sparks, ames, hot equipment) in the

immediate area around the spill.

• Do not touch or walk through spilled material.

• Avoid breathing vapors. Ensure adequate ventilation.

• Use personal protective equipment.

•

Contact Enphase Customer Support at

https://enphase.com/contact/support

or 1800 006 374

Safety Instructions, continued

Environmental Protection

ELECTRONIC DEVICE: DO NOT THROW AWAY. Waste electrical products

should not be disposed of with household waste.

Proper disposal of batteries is required. Refer to your local codes for

disposal requirements.

Assembled in China



Enphase Energy Inc.,

47281 Bayside Pkwy.,

FREMONT, CA, 94538,

THE UNITED STATES OF AMERICA

PH: +1 707-763-4784

Importer:

Enphase Energy Aust.

Pty/Ltd., 88 Market St.,

South Melbourne VIC 3205.

PH: +61 3 86691679

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali enphase Magazzinaggio

enphase

enphase IQ Battery 5P Manuale utente

enphase

enphase ENCHARGE-3T-1P-INT Manuale utente

enphase

enphase ENCHARGE-10-1P-NA Manuale utente

enphase

enphase ENCHARGE Series Manuale utente

enphase

enphase ENCHARGE-3T-1P-NA Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente

enphase IQBattery 5 Manuale utente

Manuali Magazzinaggio popolari di altre marche