Enttec ALEPH MATRIX1 Manuale utente
Quick Start
rev A
Document PN: 50346
ALEPH MATRIX1
6 4 P I X E L R G B P IXEL PANEL FOR EF F E C T L I G H T I N G A N D S I G N A G E
Electrical Connection
Addressin
Each Aleph MATRIX1 panel must be iven an address to match the handler software settin s
(refer to User manual PN:50363).
Press MENU key for 5 seconds until the address display is shown on the panel. EACH Panel
has a 3 di it address. When the number is displayed in reen it is in view mode. Pressin
ENTER key for 5 seconds will o into edit mode (red).
Mains output to next
panel. Maximum of
10Amps total load.
240V = 100 panels
120V = 75 panels
Mains input
100 → 240VAC
10Amps MAX
Data Output to next
Aleph Matrix Panel
Data Input from Aleph
Matrix USB interface
Warnin : Only ENTTEC authorised CAT5 or CAT 6 cables
must be used to maintain si nal quality.
MATRIX1
M ENU
ENT E R
→
PO W ER
→
Ra tin g:
100 -25 0V A C
50/ 6 0 H z
16 Wat ts
Da nger D o No t
Op en. L i e
Volt age s Ins ide
N29 6 8 5
made in Australia
www.enttec.com
D ATA IN
D ATA OU T
MATRIX1
ME NU
ENT E R
→
PO W ER
→
Ra tin g:
100-2 50V A C
50/ 60Hz
16 W att s
Da nger Do No t
Open . Li e
Voltag es Insid e
N2968 5
made in Australia
www.enttec.com
DATA IN
DATA OUT
Quick Start
rev A
Document PN: 50346
Self-Test
To start self test, POWER CYCLE the unit, then press the ENTER button twice, the panel will
then execute it's self test sequences. This can be performed without DATA input. Durin this
time the panel will not respond to DATA IN si nal but will still pass data throu h.
Press MENU → 5 SECONDS to view
address (GREEN)
Tens
Hundreds
Press MENU key to scroll units
Units
Press ENTER to edit the current di it (chan es to
red) and MENU to scroll the di it from 0 to F
followin the MATRIX1 Handler software Address
rid. To save the new value press ENTER for 5
seconds (until colour chan es to reen).
To exit without savin , cycle power or press MENU
The Panel ID is used in the MATRIX1 handler
software; it is NOT the Art-Net universe or subnet.
MATRIX1
MENU
ENTER
→
PO WER
→
R at ing:
100 -25 0V A C
50/ 60Hz
16 W att s
D anger D o N ot
Open. Li e
Voltage s Ins ide
N29685
made in Australia
www.enttec.com
DATA IN
DATA OUT
Back Label
Altri manuali Enttec Attrezzatura per DJ
Enttec
Enttec Phero Manuale utente
Enttec
Enttec ET Mk2 Manuale utente
Enttec
Enttec ALEPH2 ET DX4 Manuale utente
Enttec
Enttec Phero 33 Manuale utente
Enttec
Enttec Pixel Triton Manuale utente
Enttec
Enttec S-PLAY Manuale utente
Enttec
Enttec DMX USB PRO Manuale utente
Enttec
Enttec DMXIS Manuale di istruzioni
Enttec
Enttec ALEPH2 ET Mk2 Manuale utente
Enttec
Enttec DATAGATE MK2 Manuale di istruzioni
