Enviro Cube Manuale
CubeUnpacking&SetupInstructions
Contents
• Black sea ember wool (x1)
• Rear Vent Top Cover (x1)
• Unpacking & Setup Guide
(x1)
1. Remove the crate and packaging from the
unit. The unit is attached to the pallet and
will be removed at a later step.
Figure 1: Safety Screen Removal
Figure 2: Back Cover Removal
3. The rear panel is attached to the unit using
four (4) #8 T20 screws, two (2) on each side
near the back of the unit. Detach these
screws and remove the back panel. Refer to
Figure 2.
2. Remove the safety screen from the front of
the unit. Lift the screen up to disengage the
hooks and pull away from the unit. Refer to
Figure 1.
4. Lift the top cover up and o of the unit
(see Figure 3).
Figure 3: Top Plate Removal
5. Remove the front glass by lifting up to
disengage the hooks and pull away from
the unit. Refer to Figure 4.
Figure 4: Outer Glass Removal
6. Each of the side panels can now be
removed. Lift the panel up and away
from the unit. Refer to Figure 5.
Figure 5: Side Panel Removal
Figure 6: Unit Removal
7. The Cube is attached to the pallet via two
brackets at the bottom of the unit. Detach the
unit from these brackets by removing the four
(4) #8 HEX screws, two on each side. Lift the
unit up and place it off to the side for now.
Refer to Figure 6.
8. Remove the wood screws securing the brack-
ets to the pallet.
*NOTE: The next steps apply to both the pedes-
tal and platform options for the Cube. The shown
diagrams will use the pedestal as an example.
*NOTE: If you are planning to install the optional
fan kit, please complete everything up to wiring
the fan kit before continuing. The fan kit installa-
tion instructions are included with the fan kit.
*NOTE: If converting the Cube to a rear vented unit, unscrew the four (4) hex head bolts securing
the intake/exhaust adapter, rotate it 180º, and reat-tach.
*NOTE: If you are installing the optional fan kit, finish the remaining instructions (wiring the fan
kit) before continuing.
9. Place two brackets on the table and line up
the holes on the bracket to the table. Use four
(4) #8 T20 Screws to fasten. (Figure 7)
10. Retrieve the Cube unit and align it over the
brackets on the pedestal/platform. It will use the
same holes that the brackets were previously
attached to. Secure the unit to the pedestal as
shown in Figure 7.
11. The Cube is now properly secured to the
pedestal/platform. perform steps 2 through 6 in
reverse order to reattach all outer pieces of the
unit. Figure 7: Unit Attachment
Altri manuali per Cube
1
Indice
Altri manuali Enviro Camino da interno
Enviro
Enviro E33G Manuale utente
Enviro
Enviro Nova Q1L Manuale utente
Enviro
Enviro retreat Manuale utente
Enviro
Enviro E30G Manuale utente
Enviro
Enviro Q4 Manuale utente
Enviro
Enviro Westport Manuale utente
Enviro
Enviro 50-927 Manuale utente
Enviro
Enviro ENVIRO Manuale utente
Enviro
Enviro Q2G Manuale utente
Enviro
Enviro Q2L Nova Manuale utente
Enviro
Enviro C-10100 Manuale utente
Enviro
Enviro E25ID Manuale utente
Enviro
Enviro Q3LI Manuale utente
Enviro
Enviro . EG.95.FPI.BV.LPG Manuale utente
Enviro
Enviro C60ID Manuale utente
Enviro
Enviro Q2LI Manuale utente
Enviro
Enviro C-10914 Manuale utente
Enviro
Enviro E20I Manuale utente
Enviro
Enviro E30I Manuale utente
Enviro
Enviro E20I Manuale utente
