EPH Controls EMBER Manuale utente
GATEWAY INSTRUCTIONS
WWW.EPHCONTROLS.COM/EMBER
2
Welcome
Thank you for choosing EMBER by EPH Controls. We hope you
enjoy using it as much as we did developing it!
Controlling your heating anywhere, anytime is only a few simple
steps away.
In this booklet, we will provide a step by step guide to setting up
the EMBER heating control app and its associated hardware.
Again, thank you for choosing EMBER.
3
Index
Page 4 Getting started
(Router requirements/Phone software etc)
Page 18 Home screen diagram
Page 16 Home setup
Page 13 Pairing the gateway to your wireless internet
Page 8 Downloading your EMBER App
Page 7 Pairing thermostats to your programmer
Page 6 Pairing programmer to your gateway
Page 5 LCD / Button legend
4
WiFi Requirement
The SSID of your Wi-Fi should not
be hidden when you are pairing the
gateway to your router.
Please install the gateway in a place
with a good Wi-Fi signal.
The gateway can only support 2.4 GHz
wireless routers. It does not support 5
GHz wireless routers.
The MAC address of gateway should
not be in the blacklist of the router.
Please restart your wireless router
periodically or restart it before you
are going on holiday to ensure that
the connection is kept after long
periods of inactivity.
Pay attention to the number of
devices connected to your wireless
router. Some routers may not work
properly if too many devices are
connected.
Device Operating System
1) Minimum IOS is 8.
2) Minimum Android OS is 4.2.
(Jellybean)
1 Getting Started
5
LCD / Button Legend
WPS / Smartlink
button
Function button
Figure (5-a): The gateway
Figure (5-b): The RF programmer
Buttons to be used during gateway installation
6
1. Reset your router by switching it
off and on.
2. On the Programmer, press
button for 5 seconds.
3. ‘Wireless Connect’ will appear on
the screen. Figure (6-a)
4. Press the button for 3 seconds.
You will now enter the wireless
connection screen.
5. A four digit code will appear on the
screen. Figure (6-b)
6. On the Gateway, press the
‘Function’ button for 5 seconds.
7. Red and green lights on
the gateway will both ash
simultaneously every 1 second.
8. On the Programmer – R1 appears
on the screen. Figure (6-c)
9. Press the button.
Pairing programmer
to your gateway
Figure (6-a): ‘Wireless Connection’ screen
Figure (6-b): ‘Gateway Connection’ screen
Figure (6-c): ‘Gateway Connection’ screen
7
1. Lower the cover on the front of the
RF programmer. Move the selector
switch to the ‘RUN’ position.
2. On the RF programmer, press the
button for 5 seconds. Wireless
Connect will appear on the screen.
Figure (7-a)
3. On the RFR wireless room
thermostat or RFC wireless
cylinder thermostat, press the
‘Code’ button. This is located inside
the housing on the Printed Circuit
Board. Figure (7-b)
4. On the RF programmer, the
available zones will begin to ash.
5. Press the
ZONE SELECT
button for
the zone you wish to connect the
thermostat to.
6. The wireless symbol appears on
the screen.
7. The thermostat will count upwards
to the number of the zone that it is
paired with. When it reaches the
number of the zone that it is paired
with press the hand wheel on the
thermostat.
8. The RF programmer is now
operating in the wireless mode.
The temperature of the wireless
thermostat is now displayed on the
programmer.
9. Repeat this process for the second,
third and fourth zone if required.
Pairing thermostats
to your programmer
Figure (7-a) ‘Wireless Connection’ screen
Figure (7-b) Printed Circuit Board
Figure (7-c) Zone screen
Reset button Code button
RUN
CLOCK
SET
PROG
SET
8
2. Once the app has been installed,
open it.
3. Select to Sign up with your email
address.
1. Go to the Apple App Store on
your iPhone or the Google Play
Store on your Android device and
download the EPH Ember App.
QR codes to the download links
are available on the back cover.
Downloading your
EMBER App
9
9. Enter your telephone number.
(optional)
10. Press Sign up.
4. Enter your Name.
5. Enter your Surname.
6. Enter your Email address.
7. Enter your Password (Minimum 6
characters – including lowercase,
uppercase and number)
8. Conrm your Password.
10
13. You will be directed to the EMBER
app. Select ‘Open’ in Ember. If
you are not automatically directed
to the app, manually open it and
complete step 14.
11. Wait for a conrmation email
from EMBER. (This could take 1 –
2 minutes)
12. Open the email and press the
embedded button ‘Click to
activate your account’.
Downloading your
EMBER App (Continued)
Altri manuali per EMBER
1
Indice
Altri manuali EPH Controls Portale
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
