Epson RC90 Manuale utente

Altri manuali per RC90

5

Altri manuali Epson Controllori

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente

RC90 Controller –Option Board Installation Procedure Rev.2

RC90

Option Board Installation

Read this manual first

Rev.2

RC90 Controller – Option Board Installation Procedure

RC90 Option Board Installation Rev. 2 1

RC90 Option Board Installation Procedure

■Before performing any maintenance procedure, always make sure that the

main power of the Controller is turned OFF and that the high voltage charged

area is completely discharged. Performing any maintenance procedure

while the main power is ON or the high voltage charged area is not

discharged completely is extremely hazardous and may result in electric

shock and/or cause serious safety problems.

WARNING ■When opening or closing the front side, make sure that the 200 V power

supply for the Controller is OFF. Performing procedure to the power supply

terminal block inside the Controller while the power supply is ON is extremely

hazardous and may result in electric shock and/or cause serious safety

problems.

-Be careful not to damage cables. Be sure not to drop any screws into the Controller.

-Installing the front cover using the wrong screws may result in a cable being damaged

and/or malfunction of the Controller.

C Option Board

(1) Turn OFF the Controller.

(2) Unplug the power connector.

Option Board

Addition

(3) Remove the Top Panel. (Mounting screws ×10)

(4) Remove the clamp of the power supply cable.

(5) Remove the screws of the Option Slot Panel

(×4).

When installing one Option Board:

Slide the panel as shown in the picture and

install the board with screws (×2).

When installing two Option Boards:

The Option Slop Panel is not necessary.

(6) Install the Option Board as shown in the

picture.

)

NOTE

RC90 Controller – Option Board Installation Procedure

2 RC90 Option Board Installation Rev. 2

(7) Mount the attachment L-shaped plate with a

screw from the front side.

At this point, one screw for the Option Slot

Panel is left unused.

(8) Secure the L-shaped plate and Option Board

with the attachment screw.

(9) Mount the clamp of the power cable.

(10) Mount the Top Panel. (Mounting screws ×10)

(11) Plug in the power connector. Turn ON the Controller and make sure that the

Controller starts properly without any vibration or abnormal noise.

-Do not forget to configure your option after Turn ON according to your requirements.

For details see manual EPSON RC+ 5.0 User's Guide.

Available Option Boards

Part Name Code Note

Expansion I/O Board (PNP/Source type) R12B040302 24 In- / 16 Outputs

Expansion I/O Board (NPN/Sink type) R12B040303 24 In- / 16 Outputs

RS-232C Board R12B040726 2 Channels

DeviceNet Board R12B040727 DeviceNet module is

mounted on the Fieldbus

Board.

PROFIBUS Board R12B040729 Profibus module is

mounted on the Fieldbus

Board.

CC-Link Board R12B040730 CC-Link module is

mounted on the Fieldbus

Board.

)

NOTE