Epson Equity Ie Dimensioni

EPSON

Product Support Bulletin

Subject: Proper Method for Running Benchmark and Diagnostics Programs

Date: 06/04/93 PSB No: S-0158

Page(s): 1 of 1 Originator: MWT

This bulletin describes the proper method for running any benchmark or diagnostics

programs. This applies to any computer system.

In most cases, the computer should be started using an MS-DOS boot diskette

that’s ‘clean’ -

in other words, one with no CONFIG.SYS or AUTOEXEC.BAT files.

The appropriate executable can then be run, either from diskette or hard drive.

There will be some exceptions to the above rule. In attempting to benchmark or

troubleshoot any add-on that requires a device driver (CD-ROM, local area network,

etc.), obviously the necessary device driver(s) must be loaded. Also, some

programs will require a minimum number of FILES or BUFFERS to be defined in

the CONFIG.SYS file. Such programs will usually display this requirement if they

are run without the necessary CONFIG.SYS file.

For the most consistent results, use the absolute minimal boot configuration that’s

allowed by the hardware being tested.

Product Support Bulletin

Subject: Equity le - Early ROM BIOS Problem with Miniscribe 8425F

Date:

10/10/90

PSB No: S-0124

Page(s): 1 of 1

Originator: REM

A problem has been reported in the Equity le when using ROM BIOS versions earlier

than release 1.76. This version has been used in production units since September

1989. The Miniscribe 8425F hard disk drive may generate a “1701" error message

when a cold boot (power switch OFF and ON) after a warm boot (software reset or

pushing the reset switch) is executed.

When the warm boot is executed, BIOS writes the status of the warm boot to the

ROM BIOS scratch register. When a cold boot is executed after a warm boot, BIOS

should erase the status in the scratch register, however, the early BIOS does not

erase the status. The BIOS reads it as a warm boot and executes the POD, skipping

the video check and the RAM check and checking the hard disk directory. This

happens too fast for the Miniscribe 8425F hard disk drive to get ready for the BIOS

check, so it shows the “1701 error message. In the case of the warm boot only, the

hard disk is already ready, so no error message is generated.

lf this problem is encountered, run the ROMBIOS program and check the ROM BIOS

version to determine if the system needs the current version of BIOS release 1.76.

Please refer to ECN No. EQIE-005, dated 9/15/89, which described the EQUlTY le

ROM BIOS release 1.76 (CMTR-A06, -B06).

Product Support Bulletin

Subject: Equity le -

Lotus 1 - 2- 3 Graph Patch Program

Date: 6/26/90

Page:

1 of 1

PSB No: S-0121

When using Lotus 1

- 2- 3 (ver. 2.01) with the Hercules Monochrome board

or an Epson MGA board set for monochrome mode, the system displays

garbage (usually a checker board pattern) when using graphics. This also

occurs if the 90 x 25 text mode is selected in the Lotus INSTALL program,

since Hercules graphics mode is utilized.

The solution for this problem is to disable the internal MCGA video by

creating and using the program listed below. Run the MS - DOS supplied

DEBUG program and type in the following:

-A

xxxx:0100 in AL,65 ;

xxxx:0102 and AL,FB ;

xxxx:0104 out 65,AL ;

xxx"0106 int 20

;

xxxx:0108

-NMCGADIS.COM ;

-RCX

CX 0000

-W

Writing 0008 bytes

’

-Q

Comments only - do not type in

Get current value of equipment enable register.

Clear video enable bit to disable MCGA.

Output new value to the equipment enable register.

End of program.

Press <Enter> key here.

Specify name of program as “MCGADIS.COM”.

Edit CX register.

Currently contains 0000.

Specify 8 bytes to be saved.

Save program to disk.

Quit DEBUG.

Note: xxxx segment value will vary depending on system memory usage.

The MCGADIS.COM program can now be found in the current directory. It can

be added to the AUTOEXEC.BAT file or run directly, before running Lotus.

This program will enable a Hercules Monochrome board or Epson MGA board

to be used in monochrome mode, but will not allow a CGA card to be used.

Product Support Bulletin

Subject:

Equity/Apex Compatibility with the SOTA 386si

Date:

3/02/90

PSB No:

S-0111

Page:

1 of 3

Originator:

CL5

The purpose of this bulletin is to provide the 80386 Accelerator board test

results, conducted by the Computer Product Support Center, involving the

SOTA 386si from SOTA Technology, inc.

The Equity models tested were the Equity I, Equity II Equity I + and Equity le.

The Apex models tested were the Apex, Apex Plus and Apex 100. All were

tested with Norton Utilities and MS - DOS.

The table below shows compatibility and the Norton SI rating of the

various systems.

Model

Norton SI

Equity I

12.0

Equity I+

12.0/16.9

Equity le

Equity II

Apex

14.3

15.9

Apex Plus

11.5

Apex 100 12.0/16.9

Compatibility

Functioned normally with Norton Utilities and

MS- DOS 2.11

Functioned normally with MS - DOS 3.3 and

Norton Utilities at both CPU speeds.

Unable to boot at 10MHz. Performance

erratic at 4.77MHz

Functioned normally with MS - DOS 3.2 and

Norton Utilities. (Tested only at 7.16MHz.)

Unable to boot at 4.77MHz. Functioned

normally at 8MHz with MS - DOS 3.2 and

Norton Utilities.

Unable to boot at 9.54MHz. Functioned

normally at 4.77MHz with MS - DOS 3.2 and

Norton Utilities.

Functioned normally with MS - DOS 3.3 and

Norton Utilities.

PSB No: S-0111

Page: 2 of 3

Installation of the board in most of the units was quick and simple to do when

following the installation instructions accompanying the boards. Installation of

the SOTA 386si in the Equity I and the Equity II is rather difficult. Due to the

amount of disassembly required, we strongly recommend that only Authorized

Service Centers install the board in the Equity I and Equity II.

Installation Instructions

Equity I

1. Remove the following from the main unit:

a) upper case

b) rear panel

c) front panel

d) FDD/power supply block.

2. Follow instructions for a standard installation for the SOTA 386si in an

8088 - based system.

Take care to fold the SOTA connector cable so as

not to prevent reassembly.

The cable is sturdy and will tolerate being

folded.

3. Reassemble the main unit and go through the testing and initialization

procedure outlined in the SOTA manual.

Equity II

1. Remove the following from the main unit:

a) upper case

b) rear panel

c) front panel

d) FDD/power supply block.

2. Follow instructions for a standard installation for the SOTA 386si in an

8086 - based system.

Take care to fold the SOTA connector cable so as

not to prevent reassembly. This will necessitate routing the cable so that it

does not conflict with the power connection to the main system board.

The cable is sturdy and will tolerate being folded.

3. Reassemble the main unit and go through the testing and initialization

procedure outlined in the SOTA manual.

PSB No: S-0111

Page: 3 of 3

Our Computer Product Support Center receives numerous calls requesting

information and recommendations on 80386 Accelerator boards for use with the

Equity and Apex (8088-

and 8086 - based) personal computers.

We have found that the SOTA 386si may meet your requirements and are

competitively priced!

Although these boards were tested by qualified product support specialists,

Epson America makes no representations that these third party products are

compatible with all hardware configurations or software applications.

We recommend that you certify these products with your specific hardware and

software requirements and consult with the third party vendor to ensure reliable

operation.

SOTA Technology can be reached at:

SOTA Technology, Inc.

657 N. Pastoria Ave.

Sunnyvale, CA 94086

Phone: (408) 245 - 3366

Product Support Bulletin

Subject: Compatibility Information for the Equity le and Manzana Microsystems

External 5.25” 1.2MB Floppy Drive

Date:

9/12/89

Page:

1 of 1

PSB No:

S-0103

Originator: KAS

This bulletin is intended to provide the results of compatibility testing conducted

by the Computer Product Support Center with the PS/2 Connection Kit B,

PS/2 Adapter Board and the 5.25” 1.2MB external floppy drive from Manzana

Microsystems.

The PS/2 Adapter was found to support the external floppy drive as a 1.2MB

floppy drive in the Equity le.

The instructions should be followed as described

on pages 14 and 15 in the PS/2 External Drive Manual, supplied by Manzana.

The only special accommodation necessary is the use of supplied adhesive

anchor pads and cable ties to secure the PS/2 Adapter board to the mounting

bracket for the DB - 37 connector. This procedure is also outlined on page 15

of the PS/2 External Drive Manual.

MS - DOS version 3.0 or higher is required for installation of the PS/2 Adapter

Board and use of the external drive as a 1.2MB floppy disk drive. The Equity

le is shipped with MS - DOS 3.3.

Manzana includes the XDrive disk utilities with their PS/2 Adapter card. These

utilities include a device driver for the external floppy disk drive, a drive letter

query utility and an information utility for use with the external 1.2MB floppy

disk drive.

Manzana Microsystems can be contacted at the following address:

Manzana Microsystems

7334 Hollister Avenue, Suite B

P.O. Box 2117

Goleta, CA 93118

Tel. (805) 968 - 1387

Product Support Bulletin

Subject :

Novell Netware Compatibility Test Results for the Equity le

Date:

Page:

8/11/89

1 of 1

PSB No:

S-0093

Originator: KAS

This bulletin is intended to provide a summary of the results of compatibility

testing of the Equity le with Novell local- area networking products. This

information was provided to Epson by Novell’s Independent Manufacturing

Support Program.

For complete test result reports, contact Novell, Inc.

The Equity le was tested at 10MHz, as a workstation only.

Advanced Netware 2.0A

Network Boards

Gateway G - Net

IBM

Token Ring

Novell

NE1000

Novell RXNet

Proteon Pronet

SMC/PD Arcnet

Advanced Netware 2.15

Network Boards

AT&T StarLAN

Gateway G - Net

IBM

PC-Net II

IBM

Token Ring

Micom Nl5010

Novell

NE1000

Novell RXNet

Proteon Pronet

SMC/PD Arcnet

3Com

3c501

3Com

3c503

Advanced Netware 2.1

Network Boards

Novell

Intelligent NIC

Workstation Remote Boot

Passed

Failed

Passed

Workstation

Remote Boot

Passed

Not Tested

Passed

Not Tested

Passed

Failed

Passed

Not Tested

Passed

Failed

Passed

Failed

Passed Passed

Passed

Not Tested

Passed Passed

Passed

Not Tested

Workstation Remote Boot

Passed

Failed

Product Support Bulletin

Subject:

Equity and Apex Series Compatibility with the Sysgen OmniBridge

Controller and BridgeFiler External Floppy Drives

Date:

04/11/90

Page:

1 of 3

PSB No:

S-0088B

Originator:

KAS

The purpose of this bulletin is to provide the results of compatibility testing

conducted by the Computer Product Support Center with the Sysgen

OmniBridge controller and Bridge - Filer external floppy disk drives.

Comments

Equity I

The Equity I was found compatible with the OmniBridge

controller. It was able to support one or two external

disk drives (daisychained) together. The external drives

could be used as high density (1.2M and 1.44M) or

normal (360K and 720K) disk drives.

Equity II

Equity III

Equity I +

Equity le

The Equity II was found to be totally incompatible with

the OmniBridge controller.

The Equity III was found compatible with the OmniBridge

controller. It was able to support one or two external

disk drives (daisychained) together. The external drives

could be used as high density (1.2M and 1.44M) or

normal (360K and 720K) disk drives.

The Equity I + was found compatible with the

OmniBridge controller.

It was able to support one or

two external disk drives (daisychained) together. The

external drives could be used as high density (1.2M and

1.44M) or normal (360K and 720K) disk drives.

The Equity le was found compatible with the OmniBridge

controller. It was able to support only one external

floppy drive, unlike the other models tested. The drive

could be used as a high density (1.2Mb and 1.44Mb) or

normal (360K and 720K) disk drive.

PSB No: S-0088B

Page: 2 of 3

Equity II +

Equity lIe

The Equity II + was found compatible with the

OmniBridge controller.

It was able to support one or

two external disk drives (daisychained) together. The

external drives could be used as high density (1.2M and

1.44M) or normal (360K and 720K) disk drives.

The Equity Ile was found compatible with the

OmniBridge controller.

It was able to support one or

two external disk drives (daisychained) together. The

external drives could be used as high density (1.2M and

1.44M) or normal (360K and 720K) disk drives.

Equity Ill +

The Equity III + was found compatible with the

OmniBridge controller.

It was able to support one or

two external disk drives (daisychained) together. The

external drives could be used as high density (1.2M and

144M) or normal (360K and 720K) disk drives.

Equity 386SX

The Equity 386SX was found compatible with the

OmniBridge controller.

It was able to support one or

two external disk drives (daisychained) together. The

external drives could be used as high density (1.2M and

144M) or normal (360K and 720K) disk drives.

Equity 386/20

The Equity 386/20 was found compatible with the

OmniBridge controller.

It was able to support one or

two external disk drives (daisychained) together. The

external drives could be used as high density (1.2M and

1.44M) or normal (360K and 720K) disk drives.

APEX

APEX +

The Epson APEX was found compatible with the

OmniBridge controller.

It was able to support one or

two external disk drives (daisychained) together. The

external drives could be used as high density (1.2M and

1.44M) or normal (360K and 720K) disk drives.

The Epson APEX was found compatible with the

OmniBridge controller.

It was able to support one or

two external disk drives (daisychained) together. The

external drives could be used as high density (1.2M and

1.44M) or normal (360K and 720K) disk drives.

Altri manuali per Equity Ie

Indice

Altri manuali Epson Scrivania

Epson

Epson ExpressStation Manuale di installazione e funzionamento

Epson

Epson Equity 386SX/16 PLUS Manuale utente

Epson

Epson Equity LT-286e Manuale utente

Epson

Epson ActionTower 7500 Manuale utente

Epson

Epson ActionPC 2000 Foglio di istruzioni

Epson

Epson LT-286 Manuale utente

Epson

Epson 10020 Manuale utente

Epson

Epson Equity 386/25 PLUS Manuale di installazione e funzionamento

Epson

Epson Equity IIe Manuale di installazione e funzionamento

Epson

Epson Equity III Dimensioni

Epson

Epson Equity 320SX PLUS Manuale di installazione e funzionamento

Epson

Epson Endeavor 486C Manuale di installazione e funzionamento

Epson

Epson Equity 4 Manuale utente

Epson

Epson Equity 386/20 Manuale di installazione e funzionamento

Epson

Epson Endeavor P60 Manuale utente

Epson

Epson EL 486UC+ Manuale di installazione e funzionamento

Epson

Epson EQUITY II+ Dimensioni

Epson

Epson EL 4S/33 Manuale di installazione e funzionamento

Epson

Epson ActionTower 8000 Dimensioni

Epson

Epson ActionDesk 4000 Manuale utente

Epson

Epson Equity 386/25 Manuale utente

Epson

Epson Endeavor VL Manuale utente

Epson

Epson Express Station Express Station Manuale utente

Epson

Epson Endeavor Pro Manuale utente

Manuali Scrivania popolari di altre marche

HP m9060n - Pavilion - Elite Scheda tecnica

Asus

Asus E210 Series Manuale utente

Dell

Dell Inspiron 600m Manuale utente

Dell

Dell Inspiron 3662 Manuale utente

TotalFlow

TotalFlow uFLO Manuale utente

HP Presario SV7000 - Desktop PC Manuale utente

HP ProDesk 400 G5 Manuale

Logitech

Logitech MK320 Manuale utente

Dell

Dell XPS 730 H2C Manuale utente

Sony

Sony Vaio Series Manuale utente

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuale utente

Alto

Alto MD 250 Manuale utente

Lenovo

Lenovo ThinkCentre Edge 72 Manuale

Lenovo

Lenovo ThinkStation D20 Manuale

Arbor Technology

Arbor Technology FPC-7800 Series Manuale utente

Sony

Sony VAIO VGX-TP1 Series Manuale utente

Asus

Asus Eee Box B204 Manuale utente

Dell

Dell Optiplex 9010 All In One Manuale utente