Epson EMP-TW100 Manuale utente

Connecting to aVideo Source

Battery Replacement Period and

Using the Remote Control

Remote Control Operating Range

Before Using the Remote Control

Connecting to a Computer

Setup

Screen Size and Setting-up Distance

Setting-up Methods

START

Dresden SET UP GUIDE English-hyoshi

Inserting the Batteries

Printed in Japan

402167900

(9002465)

02.01-.6A(C05)

Before Using the Remote Control

The batteries are not inserted into the remote control at the time of purchase, and so you

need to insert them before the remote control can be used.

Inserting the Batteries

Remove the battery compartment cover.

While pressing the cover here, lift the cover up.

Insert the batteries.

Make sure the polarities of the batteries are correct.

Replace the battery compartment cover.

After inserting the tab of the battery cover, push the

cover down until it clicks into place.

Dresden SET UP GUIDE English-01

(illumination) button

When the button is pressed, the buttons

shown in colour in the illustration at left are

illuminated for 10 seconds. If you press the

button again during this 10-second period, the

illumination continues for another 10 seconds.

Using the Remote Control

Battery Replacement Period and

Using the Remote Control

Point the remote control

light-emitting area toward one of

the remote control light-receiving

area on the projector and operate

the remote control buttons.

Do not allow sunlight or light from fluorescent lamps to shine directly

onto the projector's remote control light-receiving area, otherwise it may

interfere with the reception of signals from the remote control.

Battery Replacement Period and Cautions

If the remote control becomes slow in responding or if it stops working, the batteries may

be spent. If this happens, replace the batteries with fresh ones.

Guide for battery replacement: Approximately 3 months if used for 30

minutes per day

*The replacement period given above may vary depending on the amount of usage and

the ambient conditions.

Use the following type of batteries as replacements.

Alkaline dry cell LR6 (AA) x 2

Remote control light-receiving area

Dresden SET UP GUIDE English-02

illumination

button

Approx. 30˚ Approx. 30˚ Approx. 30˚

Approx.

10 m

(30 ft) Approx. 30˚

Approx. ±30˚ horizontally

Approx. ±30˚ vertically

Approx. 30˚

Approx.10 m

(30 ft)

Approx. 30˚

Approx.10 m

(30 ft)

Use the remote control within the ranges indicated below. If the distance or angle between

the remote control and the remote control light-receiving area is outside the normal

operating range, the remote control may not work.

Operating distance Operating angle

Approx. 10 m (30 ft) Approx. 30˚ vertically and horizontally

Remote Control Operating Range

Dresden SET UP GUIDE English-03

300"

(660 × 370)

Screen size

0.2 m

(7.8 inches)*

Distance from center

of lens to bottom edge

of screen (cm)

*When installing to a wall, leave a space of about 0.2 m (7.8 inches)

between the projector and the wall.

30"

(66 × 37)

40"

(89 × 50)

60"

(130 × 75)

80"

(180 × 100)

100"

(220 × 120)

200"

(440 × 250)

0.9 – 1.2

1.2 – 1.6

1.8 – 2.5

2.5 – 3.4

3.1 – 4.3

6.3 – 8.6

9.5 – 13.0

5.1

5.0

6.8

6.7

10.2 13.7

13.6

17.1

17.0

34.3

34.0

51.4

51.0

Setup

The distance between the projector and the screen determines the actual image size.

Recommended distance : 0.9m - 13.0m (2.9 - 42.6 feet)

While referring to the table below, position the projector so that the image size is smaller

than the screen size.

Screen size (cm (feet))

30"

(66 × 37 (2.1 × 1.2))

40"

(89 × 50 (2.8 × 1.6))

60"

(130 × 75 (4.2 × 2.4))

80"

(180 × 100 (5.7 × 3.2))

100"

(220 × 120 (7.2 × 4.1))

200"

(440 × 250 (14.4 × 8.2))

300"

(660 × 370 (21.6 × 12.1))

5.0 – 5.1

(0.16 – 0.17)

6.7 – 6.8

(0.22 – 0.22)

10.2

(0.33)

13.6 – 13.7

(0.45 – 0.45)

17.0 – 17.1

(0.56 – 0.56)

34.0 – 34.3

(1.12 – 1.13)

51.0 – 51.4

(1.67 – 1.69)

Approximate projection

distance* (m (feet)) Distance in Fig.

A below (cm (feet))

0.9 – 1.2

(2.9 – 3.9)

1.2 – 1.6

(3.9 – 5.2)

1.8 – 2.5

(5.9 – 8.2)

2.5 – 3.4

(8.2 – 11.1)

3.1 – 4.3

(10.1 – 14.1)

6.3 – 8.6

(20.6 – 28.2)

9.5 – 13.0

(31.1 – 42.6)

Screen Size and Setting-up Distance

The projector’s lens allows a zoom ratio of up to about 1.35.The

image size at the maximum zoom setting is about 1.35 times bigger

than the image size at the minimum zoom setting.

The image size will be reduced when keystone correction is carried

out.

* Distance and dimensions should be used as a guide for installation. The actual distance will vary depending on

projection conditions.

Dresden SET UP GUIDE English-04

Front projection

Rear projection using a

translucent screen

Rear projection onto a

translucent screen with the

projector installed to the ceiling

Front/ceiling projection

The projector supports the following five projection methods, allowing you to choose the

best method for displaying your images.

After setting up the projector, refer to the User's Guide for details on turning on the power

and adjusting settings such as the screen size. ( "Basic Operations" in User's Guide)

Setting-up Methods

When turning the projector upside

down, attach the rubber stands that

are included.

This can prevent the control panel

from directly touching the

installation surface.

When setting up the projector, be sure to first read the

Safety

Instructions/World-Wide Warranty Terms

for information on the safety

precautions that must be observed at this time.

* A special method of installation is required in order to suspend the projector from the ceiling. Please

contact the place of purchase if you would like to use this installation method.

* When installing to the ceiling or projecting from behind the screen, set the Screen Mode command in the

Settings environment setting menu to match the method of projection being used.

("Settings"menu in User's Guide)

Rubber stands

(Attach in

3 places)

Projecting from locations such as the

top of a cabinet

When installing the projector upside down, set

the Screen Mode command in the Settings

environment setting menu to "Front/Ceiling".

("Settings" menu in User's Guide)

Dresden SET UP GUIDE English-05

Connecting to aVideo Source

Projecting ComponentVideo Images

If more than one peripheral device is being connected to the projector,

make the connections and then change the Input A and Input B commands

in the Advanced environment setting menu to "YCbCr" or "YPbPr" to match

the signals from these devices. ("Advanced" menu in

User's Guide

)

For HDTV (750p or 1125i), "YPbPr" will be selected regardless of the above

setting.

For SDTV(525i,625i), "YCbCr" will be selected regardless of the above setting.

Turn off the power for both the projector and the video source before connecting them.

If the power for either device is on at the time of connection, damage may result.

Check the shapes of the cable connectors and the device ports before making the

connections.If you try to force a connector to fit a device port with a different shape or

number of terminals, a malfunction or damage to the connector or port may result.

Refer to the Optional Accessories appendix in the separate User's Guide for details of the

optional cables.

If connecting using a component video cable (commercially-available)

If connecting using a component video cable (optional)

Dresden SET UP GUIDE English-06

Component video cable

(commercially-available)

To video output port

Red

Blue

Green

To Input A port

Component video cable (optional)

To video output port To Input B port

Projecting CompositeVideo Images

Projecting S-Video Images

Dresden SET UP GUIDE English-07

RCA video cable (yellow)

(commercially-available)

To Video port (yellow)

To video output port

(yellow)

S-Video cable

(commercially-available)

To S-Video port

To video output port

Projecting RGBVideo Images

After connecting, use the environment setting menus to change the "Input B"

setting in the "Advanced" menu to "RGB".

("Advanced" menu in

User's Guide

)

If connecting using a computer cable (optional)

If connecting using a DVI analog cable (optional)

Dresden SET UP GUIDE English-08

Computer cable

(optional)

To RGB output port To Input B port

ELPKC25 DVI analog cable

(optional)

To RGB output port To A-RGB/D-RGB DVI-I port

Connecting to a Computer

The projector cannot be connected to some types of computer, or projection of images

may not be possible even if actual connection is possible. Make sure that the computer you

intend to use satisfies the conditions given below.

Condition 1:The computer must have a image signal output port.

Check that the computer has a port such as an RGB port, monitor port or video port which

can output image signals. If the computer has a built-in monitor, or if using a laptop

computer, it may not be possible to connect the computer to the projector, or alternatively

you may need to purchase a separate external output port. Refer to the User's Guide for

your computer under a heading such as "Connecting an external monitor" or similar for

further details.

Condition 2:The display resolution and frequency of the computer must be listed

in the "List of Supported Signal Resolutions".

Some computers may have functions for changing the output resolution. Refer to the

User's Guide for the computer and change the setting to within a range given in the list of

supported resolutions.

Turn off the power for both the projector and the computer before connecting them.

If the power for either device is on at the time of connection, damage may result.

Check the shapes of the cable connectors and the device ports before making the

connections.If you try to force a connector to fit a device port with a different shape

or number of terminals, damage to the connector or port may result.

Dresden SET UP GUIDE English-09

You may need to purchase a separate adapter to connect the

computer to the projector, depending on the shape of the computer's

monitor port. Refer to the

User's Guide

for the computer for details.

The optional Mac Adapter Set is required in order to connect the

projector to a Macintosh computer.

Altri manuali per EMP-TW100

Indice

Altri manuali Epson Proiettore

Epson

Epson PowerLite 8300i/NL Scheda tecnica

Epson

Epson PowerLite Presenter L Manuale utente

Epson

Epson PowerLite 1260 Manuale utente

Epson

Epson EB-1965 Manuale utente

Epson

Epson PowerLite Home Cinema 8350 Manuale elenco delle parti

Epson

Epson PowerLite 735c Manuale utente

Epson

Epson MovieMate 30s Scheda tecnica

Epson

Epson Dreamio EH-TW450 Manuale utente

Epson

Epson 1810p - PowerLite XGA LCD Projector Guida di riferimento

Epson

Epson 880X Scheda tecnica

Epson

Epson PowerLite 7300 Manuale utente

Epson

Epson EH-TW5200 Manuale utente

Epson

Epson EB-735Fi Manuale utente

Epson

Epson EMP-7300 Manuale utente

Epson

Epson PowerLite 737c Manuale utente

Epson

Epson 7800p - PowerLite XGA LCD Projector Manuale utente

Epson

Epson EB-PU2213B Manuale utente

Epson

Epson PowerLite Home 20 Manuale

Epson

Epson EX21 Manuale utente

Epson

Epson PowerLite EB-805F Manuale utente

Epson

Epson PowerLite 8000i Manuale utente

Epson

Epson EF12 Manuale utente

Epson

Epson EMP-TW680 dreamio Manuale utente

Epson

Epson EMP-7550 - XGA LCD Projector Manuale utente

Manuali Proiettore popolari di altre marche

iEmmet

iEmmet MP-312 Manuale utente

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuale utente

Sony

Sony VPL-HW65ES Manuale di servizio

Toshiba

Toshiba TLP-791U Manuale utente

Philips

Philips LC1341 Guida di riferimento

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuale utente

NEC

NEC NP600S EDU Manuale utente

BenQ

BenQ SH753P Manuale utente

Eiki

Eiki EK-623U series Manuale utente

Christie

Christie LHD700 Manuale utente

Navitar

Navitar FX Manuale utente

InFocus

InFocus LitePro 560 Manuale utente

Sony

Sony SRX-R815P Manuale utente

Vivitar

Vivitar DP1500 X Manuale utente

Acer

Acer C20 Series Manuale utente

Asus

Asus ZenBeam Latte Manuale utente

BOXLIGHT

BOXLIGHT CP-322i/CP-634i Manuale utente

JVC

JVC 1108TTH-AO-AO Manuale utente