Epson ES-1200C Pro PC Dimensioni

EPSON AMERICA, INC.

Product Support Bulletin

Subject: OS/2 Warp 3.0 and Epson TWAIN

Date: 1/26/95 PSB No: P-0103A

Page(s): 1 of 4 Originator: CEB

This bulletin describes the necessary steps to implement the Epson TWAIN driver

in a Windows 3.1 session under OS/2 Warp 3.0. This procedure will cover both

current versions of Epson TWAIN (1.03 and lower as well as 2.02 and higher) using

bidirectional parallel and SCSI interfaces.

NOTE:

TWAIN v1.03 and lower will not work with the Epson ES-1200C scanner. You must

use TWAIN 2.02 or higher. If you are using the ES-1200C with a program that has

Epson scanner support, you may need install the EPSN.SYS device driver for that

Windows session. To do this, follow steps 6 through 16 below. You will need to

obtain EPSNSY.EXE from the Epson BBS. This file has the EPSN.SYS driver

included in it. Simply copy the driver to the root directory of your boot drive.

Bidirectional Parallel Interface

Epson TWAIN v2.xx

There is no special procedure required to setup this version of the driver to run in a

Windows session under OS/2 Warp 3.0. Simply launch Windows and install the

driver.

Epson TWAIN v1.0x

Follow the steps below to enable Epson TWAIN v1.0x:

From the OS/2 desktop, double click on the OS/2 SYSTEM folder

Double click on the COMMAND PROMPTS folder

Double click on the Win-OS12 icon.

Once Windows is loaded, follow the TWAIN installation procedure. When the

installation program asks if you wish to make changes to the CONFIG.SYS or

the CONFIG.ADD, select CONFIG.ADD.

Once the installation has completed, exit Windows.

If the COMMAND PROMPTS folder is not open, follow steps 1 and 2.

Move the mouse to the WIN-OS/2 FULL SCREEN icon. Click on the right

mouse button.

PSB No: P-0103A

Page: 2 of 4

10.

11.

12.

13.

14.

Select SETTINGS from the pop-up menu.

Once the SETTINGS notebook has opened, click on SESSION.

Click on the WIN-OS2 SETTINGS.

Click on OTHER DOS SETTINGS.

Click on OK.

Highlight DOS-DEVICE.

In the window to the right, add the EPSN.SYS driver. X represents the

appropriate parallel port.

X = 0 (Parallel port address 3BCh)

X = 1 (Parallel port address 378h)

X = 2 (Parallel port address 278h); This is the default setting Epson TWAIN

uses.

The device line would be entered in the following manner. Substitute 0, 1 or 2

based on your configuration.

C:\EPSN.SYS x /i79

15.

Click on SAVE.

16.

Close the SETTINGS notebook.

The next time a Win-OS/:! session is started, you will see the EPSON device driver

load. If you do not, repeat the above steps. If you have migrated a Windows

application to the OS/2 desktop, apply the above steps to that icon instead of the

Win-OS/2 icon. To verify that the configuration is correct, configure the DOS FULL

SCREEN icon using the same methods outlined in steps 6 through 16. Once you

have completed those steps, start a DOS FULL SCREEN session and run the

SCANTEST utility from the \WlNDOWS\TWAIN directory. If SCANTEST runs

successfully, chances are that the Windows session will run properly.

SCSI Interface

In order for either of the Epson TWAIN drivers to function in a Windows session

under OS/2, you must install support for your ASPI compliant SCSI card under

OS/2 first. For installation instructions, refer to your OS/2 manual.

Once you have installed support for your ASPI compliant card under OS/2, you

need to manually check the CONFIG.SYS file for four key files. You should have

the following lines in the OS/2 CONFIG.SYS. If these lines do not exist, add them.

The AHAxxxx.ADD should have been inserted when you installed the SCSI support

for OS/2.

PSB No: P-0103A

Page: 3 of 4

BASEDEV=OS2ASPI.DMD

BASEDEV=OS2SCSI.DMD

BASEDEV=AHAxxxx.ADD /V

DEVlCE=C:\OS2\MDOS\VASPl.SYS

NOTE:

This document assumes that you are using an Adaptec card. The AHA 1510 and

AHA1540C were tested when creating this document.

Once you have verified that the above lines are in the CONFIG.SYS, shut down

OS/2 and reboot.

NOTE:

If the SCSI card does not find any devices on the SCSI chain, the AHAxxxx.ADD

driver will not load thus causing VASPI.SYS not to load. If this occurs, double

check your card’s configuration and the SCSI cabling.

Epson TWAIN v1.0x

Follow the steps below to enable Epson TWAIN v1.0x:

10.

11.

12.

13.

14.

From the OS/2 desktop, double click on the OS/2 SYSTEM folder

Double click on the COMMAND PROMPTS folder

Double click on the Win-OS/2 icon.

Once Windows is loaded, follow the TWAIN installation procedure. When the

installation program asks if you wish to make changes to the CONFIG.SYS or

the CONFlG.ADD, select CONFIG.ADD.

Once the installation has completed, exit Windows.

If the COMMAND PROMPTS folder is not open, follow steps 1 and 2.

Move the mouse to the WIN-OS/:! FULL SCREEN icon. Click on the right

mouse button.

Select SETTINGS from the pop-up menu.

Once the SETTINGS notebook has opened, click on SESSION.

Click on the WIN-OS2 SETTINGS.

Click on OTHER DOS SETTINGS.

Click on OK.

Highlight DOS-DEVICE.

In the window to the right, add the EPSN.SYS driver. X represents the

appropriate SCSI ID of the scanner.

The device line would be entered in the following manner.

C:\EPSN.SYS 3 /Sx /i79

PSB No: P-0103A

Page: 4 of 4

15. Click on SAVE.

16. Close the SETTINGS notebook.

The next time a Win-OS/2 session is started, you will see the EPSON device driver

load. If you do not, repeat the above steps. If you have migrated a Windows

application to the OS/2 desktop, apply the above steps to that icon instead of the

Win-OS/2 icon. To verify that the configuration is correct, configure the DOS FULL

SCREEN icon using the same methods outlined in steps 6 through 16. Once you

have completed those steps, start a DOS FULL SCREEN session and run the

SCANTEST utility from the \WlNDOWS\TWAIN directory. If SCANTEST runs

successfully, chances are that the Windows session will run properly.

Epson TWAIN v2.xx

There is no special procedure required to setup this version of the driver to run in a

Windows session under OS/2 Warp. Simply launch Windows and install the driver.

Follow the procedures outlined in the user’s manual. If the driver does not install

properly, verify that the device drivers mentioned earlier in this section are being

executed.

Product Support Bulletin

Subject: DOS Device Driver and Interface Connection Diagnostic

for the Epson ES-300C Scanner

Date: 4/3/92 PSB No: P-0086

Page(s): 1 of 1 Originator: RSS

This bulletin was made for the purpose of announcing the availability of a DOS

device driver and interface connection diagnostic for the Epson ES-300C Scanner.

The ES-300C DOS Device Driver was developed for the purpose of allowing third

party scanner application programs to send I/O routines to the device driver instead

of writing to a specific hardware interface. The DOS Device Driver supports the

Epson Bi-Directional Parallel Interface, the IBM PS/2 Internal Parallel Interface, and

Adaptec SCSI interfaces. For information regarding how to obtain this driver, refer

to the distribution information below. If you require additional specifications on the

DOS Device Driver call the Epson Imaging Product Support Department.

The ES-300C Scanner Interface Connection Diagnostic works in conjunction with

the DOS device driver to allow quick and easy verification of the interface

connection between the scanner and host computer. The diagnostic works from

DOS, and does not require Microsoft Windows. Once the diagnostic is initiated, the

scanner will complete a page scan in less than 60 seconds on most computers.

DISTRIBUTION

The Epson ES-300C DOS Device Driver and Scanner Interface Connection

Diagnostic software are available from 4 sources:

A diskette containing all the files are included in each ES-300C DOS interface

kit. The Epson Product Code for the kit is ES300DOS-A.

The files are available from the Epson BBS. The self-extracting file name is

ES300DD.EXE. The Epson BBS telephone number is (310) 782-4531.

The CompuServe Bulletin Board has the files located in the Epson Forum.

After logging into CompuServe, type ‘GO EPSON” at the prompt to access the

Epson Forum.

Any Premier or Standard Epson Customer Care Center can order the diskette

from our Parts Order Services Department. The diskette part number is

ES3DISK.

EPSON AMERICA, INC.

EPSON

Product Support Bulletin

Subject: Image Editing Terms

Date: 6/5/91

Page(s): 1 of 3

PSB No: P-0078

Originator: RS

The following terms’ are used to describe image editing and grayscale in

connection with scanners, monitors and printers.

Additive

Primary Colors:

Aliasing:

Antialiasing :

Brightness:

Continuous

Tone:

Contrast:

Cropping:

Dithering:

DPI:

The colors produced by mixing colored light. The primary

additive colors are red, green and blue. The absence of color

produces black (0%); maximum intensity produces white (100%).

This principle is used in color monitors (RGB). By using 24 bits

per pixel it is possible to represent more than 16 million colors.

The jagged diagonal lines that appear in low resolution mode.

Usually noticeable on characters like ‘A” and "W".

The removal of the aliasing or step-like diagonal lines.

The balance of light and dark shades.

The transition from light to dark or dark to light in a smooth

uninterrupted progression. Laser and dot matrix printers do not

support continuous tones.

The range between the darkest and lightest shades of an image.

As contrast increases, the number of gray shades between black

and white decreases.

An operation that allows portions of an image to be selected.

Usually pertains to scanning technology.

A method of shading that uses black dots of varying density to

represent darker areas. This technology is used in devices that

only support black and white outputs.

Abbreviation for dot per inch. The standard measurement of

resolution for all output devices. DPI describes the number of

pixels in an image.

‘Some terms taken from PC Publishing, Jan. 1990.

PSB No: P-0078

Page: 2 of 3

Gamma

Function:

The function that defines the light intensity ratio between the

original image and the output data. The ES-300C scanner allows

the function to be altered so that when the image is reproduced

on a different type of output device, the tones in the reproduced

images will be closer to the original image.

Grayscale:

A term used to describe the output of devices that support more

than just black and white. Grayscales support up to 256 shades

of gray. The table below details the number of data bits required

to show the number of possible gray levels.

Number of

Bits

Possible Gray Levels

(black and white)

grays

4 16

grays

128

grays

8256

grays

Halftone:

The output in 1 or 2 bit data format that simulates grayscale by

creating a pattern of small dots that vary in size and density.

Halftones are used in newspapers to display photographs. The

Epson ES-300C supports 3 types of halftoning.

Highlight:

The brightest value in a continuous tone or halftone image.

Line Art:

Images consisting of only black and white pixels. Text is a good

example of line art.

tine Screen: Also known as screen ruling, it is the distance between the

centers of halftone dots. For example, a newspaper uses a

typical line screen - sixty five halftone dots per inch at a forty five

degree angle for photographs.

Matrix:

The square grid that forms the halftone dots. As the matrix size

increases, more possible variations on dot size and shape are

available.

PSB No: P-0078

Page: 3 of 3

Midtones:

Pixel:

The values in a continuous tone or halftone image correspond to

the medium values in the range. Generally the values is between

30% to 70%.

A relative unit of measuring resolution. Pixel size is relative, due

to the output device. For example, a monitor pixel may be

different in size compared to a scanner pixel. Pixels can be

measured absolutely when fixed to another standard, like pixels

per inch.

Posterize:

To limit the number of shades in an image to create a highly

contrasted effect.

Screen Angle:

The angle at which halftone dots are lined up. As mentioned

earlier, newspapers commonly use a screen angle of forty five

degrees.

Smoothing:

An operation that softens the edges between adjacent tones.

Spot Function:

A procedural body in the Postscript language that defines the

shape of the halftone spot.

Subtractive

Colors that are produced by mixing inks or paints. The three

Primary Colors:

subtractive colors are cyan, magenta, and yellow. This process

reduces the amount of light that the human eye receives. The

absence of color is white (0%), while full intensity is black (100%).

This model is used in printing.

Threshold:

The selected gray level above which gray shades are converted

to white and below which gray shades are converted to black.

This is used to produce higher contrast or posterize images.

EPSON

EPSON AMERICA INC.

Product Support Bulletin

Subject:

Laser & Non-Impact Printer Error Codes

Date: 4/3/91

PSB No: P-0077

Page(s): 1 of 11

Originator: JV

Epson printers issue beep tones and/or displays error codes when certain error

conditions exist. Those beeps or codes can assist you in locating and repairing

customer’s printers. The following error codes are listed by product name.

EPl-4000 Display Codes

(blinking)

*-)

YY (blinking)

*--)

YY (blinking)

E9 (blinking)

E0 (blinking)

Paper End (out) detected

Cover open

Ink low

Ink End (out)

Paper jam

Heater error (broken heater wire)

Contact error (heater fan or thermistor contact)

CO34 DVR board error

CO34 Main board software Error I

(YY will be a number from 66(H) to 7D(H))

CO34 Main board software Error II

(YY will be a number from 02(H) to XB(H))

Board contact error, CO34 Main board hardware

(YY will be one of the following numbers: 80,81,84,85,

86,87,8A, 8C)

CO34 Main board hardware error

Abnormal voltage

Buffer overflow for fonts

PSB No: P-0077

Page: 2 of 11

EPl-4000 cont.

Buffer overflow for graphics

Card error

Paper size error

Lr Release lever error

Envelope lever error

Data processing

Depress the Form Feed button

EPL-6000/ActionLaser/ActionLaser+ LCD Codes

CHANGE DRUM

The drum needs to be changed. The drum cartridge may

not be installed, the cartridge may not be installed

properly or the cartridge may be defective.

COVER OPEN

Printer cover is open

CPU ERROR

Printer’s CPU has made a calculation error

ERROR 10

Program ROM error

ERROR 11

Font cartridge or identity cartridge checksum error

ERROR 12 RAM error

ERROR 20

Memory overflow

ERROR 21

Print overrun error

ERROR 22

Receive

buffer overflow

ERROR 30

Memory error

ERROR 31

Scanner error

ERROR 32

Heater (Heat Roller Unit) error

Altri manuali per ES-1200C Pro PC

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Epson Scanner

Epson

Epson Perfection 660 Manuale utente

Epson

Epson 1640SU - Perfection Photo Scanner Manuale utente

Epson

Epson FF-640 Manuale utente

Epson

Epson GT-20000 Manuale utente

Epson

Epson DS-320 Manuale utente

Epson

Epson 1640SU - Perfection Photo Scanner Guida all'installazione

Epson

Epson Perfection V600 PHOTO Manuale operativo e di manutenzione

Epson

Epson B81306 series Manuale utente

Epson

Epson 30000 - GT - Flatbed Scanner Dimensioni

Epson

Epson Perfection 660 Manuale utente

Epson

Epson 836XL - Expression - Flatbed Scanner Dimensioni

Epson

Epson Expression 1600 Manuale utente

Epson

Epson Scanner Manuale utente

Epson

Epson DS-70000 WorkForce DS-70000 Istruzioni per l'installazione

Epson

Epson SeriesPerfection 1240U Series Dimensioni

Epson

Epson ES-1200C Pro PC Manuale elenco delle parti

Epson

Epson DS-30000 Manuale utente

Epson

Epson DS-530 Manuale di istruzioni

Epson

Epson Perfection 636U Manuale utente

Epson

Epson RR-60 Manuale di istruzioni

Epson

Epson Expression 636 Manuale utente

Epson

Epson Perfection 610 Scanner Guida all'installazione

Epson

Epson WorkForce GT-1500 Manuale del proprietario

Epson

Epson V500 Manuale di istruzioni

Manuali Scanner popolari di altre marche

Plustek

Plustek Scanner Manuale utente

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manuale utente

Renkforce

Renkforce DS100-5M Manuale utente

Image Access

Image Access WideTEK A2 Manuale utente

Canon

Canon imageFORMULA CR-120N Manuale utente

Fujitsu

Fujitsu FI-4860C2 Manuale utente

GeoSlam

GeoSlam ZEB Horizon Istruzioni per l'installazione

Kodak

Kodak i5800 Scanner Manuale utente

Kodak

Kodak i7300 Manuale utente

Revopoint

Revopoint POP Manuale utente

Fujitsu

Fujitsu fi-4860C Manuale utente

Eddyfi Technologies

Eddyfi Technologies Floormap X Manuale utente

Faselase

Faselase F6 Manuale utente

Fujitsu

Fujitsu CardMinder Manuale utente

Uniden

Uniden BC340CRS Manuale utente

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manuale utente

Mustek

Mustek PageExpress 4800 Pro Manuale utente

Optex

Optex 750830 Manuale utente