EPV DarkStar UST eFinity Series Manuale utente

V120617-ESC100 www.epvscreens.com 1

Dark Star® UST eFinity Series

EDGE FREE®Ambient/Ceiling Light Rejecting

Ultra-Short Throw Fixed Frame Projection Screen

USER’S GUIDE

Product Description:

The DarkStar® UST Series is an ultra-short throw fixed frame projection screen that uses EPV’s EDGE

FREE®technology. It is designed for Ultra-Short Throw Projectors only, for use in environments where

ceiling light cannot be entirely controlled. It includes an LED backlight kit and an ultra-thin bezel to further

enhance the frame appearance.

Screen Maintenance

Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the

projection image. For optimal results we advise to pay attention to the following instructions.

1) The screen surface has a horizontal lens structure. DO NOT wipe the screen up and down or in a circular

motion. Wipe very gently from left to right only.

2) Please clean the dust on the screen surface with a soft brush or microfiber cloth (rough towel or cloth

may damage the screen’s surface).

3) Gently wipe the screen with a moistened microfiber cloth with mild soap diluted in water.

Notes：

The following precautions should always be followed to avoid damaging the material, which is not

covered under warranty.

▪Don’t touch the screen material to avoid leaving fingerprints. Use gloves when handling the material.

▪Don’t scratch the material, as it will leave permanent markings on the screen’s surface.

▪Don’t point to the screen material with a fingertip or other sharp objects to prevent damage to the

material.

▪Don’t use acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using

such chemicals will permanently damage the screen.

V120617-ESC100 www.epvscreens.com 2

1. Frame and Edge Trim Parts List

Qty

item

2 pcs

Main Frame Parts

Qty

item

2 pcs

Edge Trim Parts

Part A.

vertical frame

Part D.

Part B.

½ horizontal frame

Part E.

Part C.

½ horizontal frame

Part F.

2. Hardware Parts List

V120617-ESC100 www.epvscreens.com 3

Frame Assembly

Step 1: Place the soft padded EPE sponge on clean area on the ground where the screen will be assembled.

Step 2: Position the pieces of the frame on the EPE sponge in the arrangement shown below

Step 3: Remove the foam in all frame ends before assembling the frame

Note: Springs are pre-inserted into the grooves of the frame.

Please make sure to avoid the springs from slipping out of the

grooves when you remove the foam.

Item

Parts List

EF100HUST-DS

EF120HUST-DS

Center Joints (1)

Elbow Joints (2)

M4x6 Screws

Spring Hook

Spring (pre-installed)

Top wall brackets

M5x50 Wall Screws

Hollow Wall anchors

Bottom wall brackets

Angle cover

LED light strip clip

Center Support Bar

White gloves

Fiberglass Rod

2. Hardware Parts List

Remove the foam

V120617-ESC100 www.epvscreens.com 4

Step 4: Insert the center joint (a) connectors into one-half of the horizontal frame (b/c) and secure with the

M4x6 screws (c).

Step 5: Connect the elbow joints (b) to the top and bottom sections of the vertical frame. Once inserted, connect

the vertical sections of the horizontal frame sections. Make sure all holes are in alignment and the frame pieces

are flush (no gaps). They should form perfect right angles.

Step 6: Secure the elbow joints by fastening them with M4x6 screws (c), 4 at each corner.

Screen Material

Please read this important note before proceeding with the installation process of the material.

Before handling the Dark Star® UST material, put on the supplied pair of white gloves to avoid leaving

fingerprint marks, dust or hand oil on the material’s surface. The Dark Star® UST material is very delicate

and should be handled with extreme care. Do not allow the material to fold or bend. Failure to follow

instructions will result in permanent damage to the screen material, which is not covered by warranty.

V120617-ESC100 www.epvscreens.com 5

Step 7: Put on the white gloves (m) and carefully unroll the screen material on a clean surface from the roller to

the other side as shown below. The back side of the screen material should be placed upwards.

Step 8: Insert the fiberglass rods (n) through the openings. The longer rods are used on the vertical edges of the

screen material, and the shorter rods are used on the horizontal edges, as shown below.

Step 9: Carefully and gently place the assembled frame on top of the screen material. Make sure to not allow

the angle edge of the frame to come in direct contact with the screen material to avoid puncturing it.

Note: Make sure all of the corners of the frame are aligned according to the markings on the back of the

material as indicated below.

Fiberglass rods

Openings

RFront

Back Side

V120617-ESC100 www.epvscreens.com 6

Step 10: Use the spring hook (d) to attach the spring (e) to the hole located on the screen material’s outer edge

in the following order. Make sure the spring hook goes over the rod.

Attach the four corners first (1).

After those are secure, connect the vertical portions of the material, begin in the center and move towards the

corners (2). Lastly, connect the horizontal sections of the material by connecting the center of the material and

make your way towards the corners (3).

Note (after all springs have been attached):

Correct material installation –Corners of the screen material are properly wrapped around the corner edges of

the frame and material is evenly tensioned and flat, creating a nicely taut surface.

Incorrect material installation –The corners of the screen material are not properly wrapped along the edge of

the frame leaving the material with unbalanced tension and an uneven finish. To correct, detach springs from

material at the corner(s) where material does not lie flat along the edge of the frame, reposition the material so

that it lies flat and wraps along the edge of the frame, and reattach springs to the material.

To avoid ripples forming in the material it is imperative that all the corners are properly wrapped around the

edges as illustrated in the check mark diagrams above.

Attach springs to holes

Repeat on all sides

V120617-ESC100 www.epvscreens.com 7

Center Support Bar

Step 11: Insert the Center Support

Bar (i) into the upper top groove on

the back of the frame with the bottom

end near the approximate center point

of the frame and rotate it in at an angle

so that both ends of the bar are in

alignment with the groove.

Attention: Do not proceed with the Edge Trim installation until making sure there are no ripples in the material.

Pre-check prior to Edge Trim Installation

Correctly distinguish the top

and bottom of the DarkStar®

UST material. Place the

assembled screen on the ground.

Look down on the screen. If the

material looks white/gray as

shown below then it is correct.

If the material looks black as

shown below, then it is upside

down.

Edge Trim Installation

Step 12: Place the Edge Trim over each end of the frame and secure with M4x6 screws (c).

Start with the center points first, then the rest of the corners as shown below.

V120617-ESC100 www.epvscreens.com 8

Step 13: Install the angle cover (j)on each corner of the frame and install the LED light strip to hold down the

angle cover (or just use the clips if LED kit will not be installed). Then insert the LED light clip (l) to hold the

LED light strip in place.

Wall Installation

Step 14: Measure the overall length and height of the frame and drill holes for the top brackets. Line up the wall

brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver. If not

installing into a structural wood stud, use a hollow wall anchor then screw in the M5x50 wood screws with a

screwdriver. Make sure the brackets are leveled.

V120617-ESC100 www.epvscreens.com 9

Step 15: Position the fixed frame screen onto the top wall brackets as shown below and push down at the center

of the top of the frame to secure.

Step 16: With the frame slightly tilted outward; connect the bottom brackets onto the bottom groove of the

frame. Then secure them by screwing onto the wall.

For Technical Support or an Elite Prime Vision contact in your area, visit

www.epvscreens.com

Indice

Altri manuali EPV Schermo di proiezione

EPV

EPV Power Max Sonic 2 Series Manuale utente

EPV

EPV Efinity Edge Free Series Manuale utente

EPV

EPV Twilight Portable Series Manuale utente

EPV

EPV Polar Star eFinity Series Manuale utente

EPV

EPV PMX92HT2-E12 Manuale utente

EPV

EPV Sonic AT8 ISF Series Manuale utente

EPV

EPV Marquee Tension Series Manuale utente

EPV

EPV Power Max Tension ISF Series Manuale utente

EPV

EPV PowerMax Tension Series Manuale utente

EPV

EPV PowerMax Series Manuale utente

EPV

EPV Prime Vision ISF Series Manuale utente

EPV

EPV Twilight Portable Series Manuale utente

EPV

EPV Prime Vision ISF Series Manuale utente

EPV

EPV Dark Star UST eFinity Series Manuale utente

EPV

EPV Peregrine ISF Series Manuale utente

EPV

EPV Polar Star eFinity 2 Series Manuale utente

EPV

EPV Dark Star UST 2 eFinity Series Manuale utente

EPV

EPV Twilight Portable Series Manuale utente

Manuali Schermo di proiezione popolari di altre marche

FART PRODUKT

FART PRODUKT Standard SCREEN Manuale utente

Draper

Draper E Series Manuale

Elite Screens

Elite Screens Elite Tripod Series Manuale utente

Laarhoven

Laarhoven Companion II Manuale utente

Renogy

Renogy RMS-LFPS-US Manuale utente

Da-Lite

Da-Lite ExecutiveElectrol Manuale utente

Samsung

Samsung S*H65* Manuale utente

FONESTAR

FONESTAR PPTR-43100-FA Manuale utente

Slide Clear

Slide Clear Varro XL Manuale utente

Elite Screens

Elite Screens M85XWS1-SRM Manuale utente

OS РХ-090Н Manuale utente

Niko

Niko 10-845 Manuale utente

Speaka Professional

Speaka Professional 2357532 Manuale operativo

Sima

Sima XL-72 Manuale utente

Jasic

Jasic EVO 2.0 ET-200P Manuale utente

Elite Screens

Elite Screens Starling 2 Series Manuale utente

InFocus

InFocus SC-WALL GRY-92H Manuale

Barco

Barco OverView MVL-615 Manuale utente