Equalizer Express 360 SR1418360 Manuale utente

120-Volt Electric

Equalizer

® Express® 360

Users Guide & Exploded View

SR1418360

CAUTION

Discard the blade when it has been sharpened down to the line that

says - DO NOT SHARPEN BELOWTHIS LINE.Using a blade that has been

sharpened below this line will eliminate the flexibility of the blade and

damage the tool.The blade is extremely sharp and can cut even when

the tool is not in operation!

Equalizer® Express® 360 • 120-Volt Users Guide

Tool Description

The Equalizer®Express® 360 120-Volt tool is a multipurpose

auto glass removal tool, designed primarily for inside use on

bonded auto glass parts. It may be used outside on A-pillars

for windshields of some vehicle models, and on all broken

tempered parts.The blade shaft is enclosed in a sheath which

protects interior car parts. Most of the cutting is accomplished

on the end of the blade, therefore the operator utilizes upper

torso muscles, making the tool easy to operate and ergonomi-

cally friendly.The Equalizer®Express®360 120-Volt tool’s specific

blade stroke length and dynamic two-way cutting power slices

through the toughest urethane adhesive with ease.

The Blade

The blade is very thin and flexible about 1/2" behind the line

that says Do Not Sharpen Below This Line. If you sharpen below

that line the blade will not flex properly and that will damage

the sheath and can damage the drive unit of the tool. It is

sharpened on three sides and on a single plane.The blade must

be properly orientated (flat side rides against the glass).When

properly orientated the blade’s sharpening design causes the

blade to cut along the bottom surface of the glass, thereby

protecting headliners and mouldings from damage.

The blade is thin in this area so it will

flex to fit the contour of the glass.

Removing & Replacing The Blade

Warning: Before changing a blade the tool should be dis-

connected from the power source.

To put a blade in the tool, the blade latch must be rotated

90°.You can rotate the blade latch with your finger, finger-

nail, or a straight screwdriver. Put a blade into the tool until

it stops. Push in lightly on the blade and rotate the blade

latch until the blade drops into place. Release the blade

latch and it will rotate back in the opposite direction locking

the blade in place.

Warning: The proper way to hold the tool is to hold the

front part by the rubber boot. Do not hold the tool by the

aluminum foot assembly as this may result in your fingers

being pinched by the moving blade holder.

The Sheath

The sheath provides protection for the dash and interior vehicle

parts. Since the cutting is done by the end of the blade, the

sheath remains free of contaminants and no cleaning is neces-

sary.To keep the sheath cool we recommend that you periodi-

cally apply a light film of high heat grease to the blade part that

is inside the sheath.

Voltage...................................... 120volts

Amps ............................................. 13

Watts .......................................... 1,560

StrokesPerMinute............................. 0-3,000

Proper Use Of Your Equalizer®Express®360

Begin the cutting process by spraying the entire cutting area

and blade with cutting lubricant. Lubrication is vital for maxi-

mum cutting ease. Failure to use cutting lubricant increases

cutting friction and will cause tool damage. Periodically during

cutting, spray the blade with cutting lubricant. In the absence

of cutting lubricant you can use water.

Rust Prevention

To prevent rust caused by water droplets, every day

place a few drops of oil into the sheath and allow it to

run down into the blade holder.

Start cutting from the inside top center of the glass. Cut toward

the A-pillars and down the side to the bottom corner of the

glass (

On some models you can cut the sides from the out-

side of the vehicle).

Keep the blade properly orientated and

flat against the glass. Reverse and cut from the top center of the

glass toward the other A-pillar. Relax and let the tool do

the work.

After both sides are cut, insert two PUMPER™s (Equalizer®

LB779) to increase the cutting angle, thereby improving cut-

ting ease. For an even greater cutting angle, slightly deflate

the PUMPER™s then fold in half and re-insert.

One of the great new features of the Equalizer®Express®360 is

the ability to rotate the handle so you can get into confined

or awkward spaces.To rotate the handle, pull the release latch

back and twist the front barrel.The handle will rotate and lock

in 45° increments. Because of it's unique design, it can be swiv-

eled 360˚ around (without turning it backwards) to get back to

the standard configuration.

Oscillating

Reciprocating

When set to reciprocating the

blade will move in a straight back

and forth direction. When set

to oscillating the blade moves

back and forth and as it reaches

the end of it's stroke it moves up

slightly as it reciprocates. Besides

the in and out thrusting this gives

some sideways cutting ability to

the blade.

The plunge cut

The angle cut

Figure 1

Between each removal

Every ten removals

Figure 3

BI1038

Pumper™ can be folded in half

to increase distance of outward

pressure.

General Safety Information

1. Always wear safety glasses and safety gloves when using

the Equalizer®Express®360 120-volt tool.

2. Do not activate Equalizer®tools until they are in the cutting

position.Disengage the tool and let it stop before taking it

out of the urethane.

3. The blade is sharp and can cut even when the tool is not

running.

4. Do not force the tool. Put light forward pressure on the

tool and let it do the work.

5. Consider your work environment. Do not use or expose

power tools to rain or damp weather.

6. Unplug the tool from the electric source before servicing

and when changing accessories.

Stay Alert! Watch what you are doing and use common

sense.

After the top and sides are loose, cut the bottom of the glass loose by

starting at the center and cutting toward the sides (fig.1).A Pumper™

(Equalizer®LB779) can make this process easier. On some vehicles

the angle of the corner will not allow you to cut all the way into the

corner. On these vehicles you can plunge cut down from the top to

completely release the corners (fig. 2).

Figure 2

Changing the Sheath

IMPORTANT -- PLEASE READ CAREFULLY!

The sheath is not adjustable! The four top screws are secured

in place with Loctite®to prevent loosening from vibration, and

are not meant to be removed unless you are replacing the

sheath. Please be aware that some force may be required to

remove these screws. If difficulty is encountered, to prevent

stripping of the screws we recommend warming the sheath

retainer with a heat gun or other warming device and follow

these steps:

1. Loosen the screws with a 3/16”hex wrench.

2. Make note of the built-in sheath stop located at the back of

the sheath holder. This is very important!

3. Remove the old sheath.

4. Insert the new sheath until it touches the stop, but do not

insert the sheath past the stop!

Blade Sharpening

A sharp blade is crucial for effective cutting action and tool

longevity. A dull blade will destroy the drive mechanism

in your Equalizer®Express® 360 120-Volt. Keep the blade

sharp! Sharpen the blade between each removal with a dia-

mond file (Equalizer®BI1038).Be careful to maintain the original

sharpening angle (see Figure 3).Every ten removals, re-sharpen

the blade on a bench grinder. Keeping a sharp blade will help

the tool cut faster and prolong te life of the tool. A sharp blade

will reduce vibration,minimizing the fatigue of the operator.

Most tool damage is caused because the blade has not

been kept sharp. We will not warranty tools when the

blade has not been kept sharp!

Model SR1418360

ES1406

2750

2753

2754

2755

2756

2761

2757

2758

2759

2760

2763

2762

Part No. Description Quantity

ES1406 Sheath 1

2750 Sheath clamp (2-piece) 1

2751 Sheath clamp screws (set of 4) 1 set

2752

Complete sheath clamp assembly (includes 2-pc sheath

clamp,

2651 screws, 2652 screws, & ES1406 sheath) 1

2753 Gear case includes all internal parts 1

2754 Gear case cover boot 1

2755 Drive motor assembly 1

Part No. Description Quantity

2756 Brushes (set of 2) 1 set

2758 Switch 1

2759 Swivel lock release 1

2760 SR1418360 Express®replacement handle set 1 set

2761 Swivel lock 1

2762 Electric cord lock 1

2763 Electric cord 1

2751

2752

Toll Free USA & Canada 1.800.334.1334

International 512.388.7715 • Fax 512.388.4188

eMail • sales@equalizer.com • Web-Site • www.equalizer.com

TOOL SERIAL #_____________________________________________________________

TOOL TYPE________________________________________________________________

DATE YOU PURCHASED THIS TOOL______________________________

YOUR COMPANY___________________________________________________________

ADDRESS________________________________________________________________

CITY________________________________STATE______________ZIP CODE________

TELEPHONE NUMBER ( )____________________________________________

YOUR NAME_________________________

YOUR POSITION______________________

PURCHASED FROM_________________________________________________________

THEIR ADDRESS______________________________________________________

CITY, STATE, ZIP___________________________________________________

WARRANTY

TOOL SERIAL NUMBER

KEEP THIS FOR YOUR RECORDS

All Equalizer®Express®tools are warranted for one year to be free of factory defects. Warranty does not apply to abuse,

misuse, or normal wear and tear.We will repair or replace, at our option, any defective part.Tools are repaired and sent

back the same day they are received.

If you feel your tool is covered under warranty, the entire tool, including all blades, must be returned to:

EQUALIZER INDUSTRIES, INC.

1304 WEST INDUSTRIAL BOULEVARD

ROUND ROCK,TEXAS 78681

If you want a tool repaired, but are not seeking to have it repaired under warranty, we would still like for you

to return the complete tool including the blades.

Equalizer Industries, Inc., reserves the right to refuse to repair, at our expense, any tool which has not been

properly maintained as specified in the Users Guide. Particularly important are the following:

1. KEEPTHE BLADES SHARP!!!!!This is the one thing most technicians WILL NOT do and itWILL damage the tool.

2. Use a cutting lubricant. If you are using the short cut method (not recommended by anyone anymore) use only clean

water as a cutting lubricant.

3. DO NOT HIT THE PINCHWELD. THIS WILL DESTROY THE DRIVE MECHANISM OF YOUR TOOL.

If you have any questions about your tool, call us toll free at 1-800-334-1334 or fax us at (512) 388-4188.

Detach and return

WARRANTY REGISTRATION

Please PRINT clearly and fill in all of the blanks.

Place in envelope and mail to address on right. 1304 West Industrial Boulevard

Round Rock, TX 78681

Altri manuali per Express 360 SR1418360

Indice

Altri manuali Equalizer Utensili elettrici

Equalizer

Equalizer Magnum XP EM415 Manuale utente

Equalizer

Equalizer EM415 Manuale utente

Equalizer

Equalizer FC10TE Istruzioni per il montaggio

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale