Equilume Stable Light Manuale utente

performance lighting

Stable Light Product Manual

Contents

1. Introduction 4

2. Product Information 4

2.1 Specications 4

2.1.1 Stable Light 5

2.1.2 Controller 5

3. Installation instructions for electricians 6

3.1 Warnings 6

3.2 Installation Instructions for Stable Light and Controller 6

4. Safety Information 8

5. Getting Started: Instructions for Users 8

5.1 How to navigate through the Controller menus 8

6. How to Set-Up, Pair and Program Lights 8

7. How to deactivate a light or change programs 12

8. How to turn on the white light for an individual Stable Light at night 12

9. How to deactivate an individual white light at night and return to the default program 13

10. How to activate the white light at night for all lights in an emergency 13

11. How to change PIN Number 13

12. How to change date and time 13

13. How to change Controller ID 13

14. How to change Location 14

15. Care and cleaning 14

16. Product warranty 14

17. Technical support 14

1. Introduction

The Equilume Stable Light provides the horse with biologically effective light in

a system that replicates the benets of nature’s environmental lighting for the

stabled horse. When installed and programmed according to this manual, the

lights are designed to maximize health, performance and breeding efciency

by naturally strengthening the horse’s circadian rhythms.

2. Product Information

2.1 Specications

Specications Controller Stable Light

Input power/current 55W 300mA

Output power/current 50W 1A

Protection Over voltage, load and

temperature

Over voltage and load

Mains Frequency 47-63 Hz 47-63 Hz

IP Rating IP65 IP65

Dimensions 140 x 110 x 60 mm (5.5 x

4.3 x 2.4 in)

384 x 384 x 230 mm (15 x

15 x 9 in)

Weight 0.7 kg (1.5 Ibs) 4.2 kg (9.3 Ibs)

RF Frequency – EU/UK 868 MHz 868 MHz

RF Frequency – AUS/NZ 915 Mhz 915 Mhz

RF Frequency – USA/CA 915 Mhz 915 Mhz

Range RF: 0 - 1 km (0 - 0.6 mi) RF: 0 - 1 km (0 - 0.6 mi)

Light coverage 4.5 x 4.5 x 3.5 m (15 x 15

x 11.5 ft)

Operational

temperature range

-20º C to 50º C* (-4º F to

122º F)

-40º C to 50º C (-40º F to

122º F)

Rated Life (24/7

operation)

> 50,000 hrs > 30,000 hrs

Limited Warranty (24/7

operation)

2 years 3 years

Compliance CE, WEEE, RoHS, EMC

and FCC

*The screen on the Controller is rated to withstand temperatures from -20º C to +50º C (-4º

F to 122º F). If environmental temperatures are expected to exceed this range then it is

recommended that the Controller is further insulated.

2.1.1 Stable Light

The Stable Light is powered by a single-phase mains electrical cable at a

voltage of 80-264 VAC and is provided with 30 cm (11.8 in) mains ex cable

with an IP65 rated in-line connector so that the installer can connect with ease

to the mains electrical supply. The Stable Light measures ambient light and

adjusts its output accordingly to create the desired light intensity within the

beam range. The Stable Light is protected by a protective guard (blue cover)

to protect against ingress of dust and debris. This provides full upright coverage

and ventilation.

The protective guard has openings on either

side for the installation of a mounting bracket

(U shape) that is supplied separately when

required. This bracket can be connected to

the internal Stable Light chassis. This allows the

Stable Light to operate at an angle if needed.

The Stable Light is resistant to corrosion and

degradation that could be caused by nitrates

and other gases produced within the stable

environment.

2.1.2 Controller

The Controller is powered by a single-phase

mains electrical cable at a voltage of 80-264

VAC and is provided with 30 cm (12 in) mains

ex cable with an IP65 rated in-line connector

for the installer to connect with ease to

the mains electrical supply. The Controller

comprises a 9 cm (3.5 in) anti-glare colour

screen with a white backlight situated above

a variety of buttons. The buttons are integral

to the membrane with 5 main control options;

up, down, right, left and select. There is also a

red emergency override button (!) that when

pressed, turns on the bright white light in all

Stable Lights paired with that Controller.

2.1.3 Accessories

A 2 m (6.6 ft) black chain and 2 carabiner clips are provided, to enable the

hanging of the Stable Light vertically via the main loop on the top.

3. INSTALLATION INSTRUCTIONS FOR ELECTRICIANS

Please read the instructions carefully before use to ensure safe and satisfactory

operation of this product. Please keep these instructions for future reference.

3.1 Warnings

• This product is an IEC protection Class I appliance and must be earthed.

• The Stable Light is for indoor use only.

• The light source within the Stable Light is non-replaceable. When the light

source expires, the entire Stable Light must be replaced.

Please read these instructions carefully before commencing installation.

Install in accordance with the IEE Wiring Regulations and Building Regulations.

To prevent electrocution, disconnect at mains supply before installing Stable

Lights. The Stable Lights should be connected to a 5-amp fused circuit. If

replacing an existing tting, make a note of the connections.

Note: The Stable Light is to be suspended 3.5 m (11.5 ft) from the ground and in the

centre of the stable where possible. If installing in an open barn, space each Stable Light

approximately 4.5 m (15 ft) apart.

3.2 Installation Instructions for Stable Light and Controller

Requirements for installation of Stable Lights:

• Small Phillips athead screwdriver

• Bracket/screws suitable to attach the hanging loop or chain to the roof/

ceiling of the stable/barn

Each Stable Light has its own identication number and identication number

cards. Please attach one of these cards outside the stable in which the

Stable Light is to be installed for easy identication. The Controller will identify

the Stable Light by this number. Users can later change this number on the

controller to a suitable name for the stable or animal.

1801 - 02 - 1234

Step 1: Disconnect the mains power. When replacing an existing light tting in

stable/barn, carefully note the position of each set of house wires. Where a

ring/loop circuit exists, there will be a fourth set of wires (usually red) that are not

connected to the Live (L) or Neutral (N) of the tting. This circuit must be kept

together in the 4th terminal of the connection block, and insulated from the

tting and the other wires. The ring/loop will remain live unless isolated at the

mains or circuit breaker regardless of the position of the wall switch.

Step 2: Having identied the wiring, connect to the connection block included

with the Stable Light and/or Controller in the following way:

Please ensure that...

• House wires are correctly identied

• The connections are tight

• No loose wires have been left out of the connection block

• The lid is tted tightly onto the connection block case

A fourth connection block can be used should it be needed to make a loop

connection. This is not provided. The connection block must be wrapped in

insulation tape covering at least 2 cm (0.9 in) of the wiring on each side.

Requirements for installation of Controller:

• 4x screws and wall plugs to attach Controller to wall surface

When installing the Controller, make sure it is positioned such that the

Emergency override button (!) can be accessed at all times. To install the

Controller, please follow steps 1 and 2 above.

Step 3: Replace fuse or circuit breaker and reconnect mains power. The

Equilume Stable Lights are now ready for pairing and programming using the

Controller.

LABEL

BLANK

4. Safety Information

• Always switch off the main power supply before replacing or cleaning the

Equilume Stable Light.

• Replace external cables if damaged to avoid electrical hazards.

• The Stable Light should be positioned so that prolonged direct exposure to

the eye at distances closer than 0.4 m (1.3 ft) is avoided.

5. Getting Started: Instructions for Users

5.1 How to navigate through the Controller menus

Use the navigation buttons on the Controller to navigate around the screen.

These are; up (˄), down (˅), left (<), right (>) and select (•).

Highlight icons on screen using the navigation buttons and press select (•) to

enter.

Select the OK () symbol to proceed following data entry.

Select the BACK ( ) symbol to return to previous menu.

Select the HOME ( ) symbol to return to the HOME menu at any stage.

6. How to Set-Up, Pair and Program Lights

Once connected to power, the Controller will show the Equilume logo for 3

seconds before going directly to the start-up menu screen. On initial activation

of the Controller, users are asked to enter Controller ID, time and location data.

This is a one-time data entry procedure at set-up, but details can be changed

at any time in the future if necessary.

Step 1: Ensure mains power is turned on.

Step 2: Set Controller ID

The screen will display the ‘SET CONTROLLER ID’ window. If using a single

Controller to manage Stable Lights, select 1. If multiple Controllers are required

for larger facilities then give each additional Controller a new ID (1, 2, 3.. etc).

Select  to save. Controller ID is now set.

Step 3: Set date and time

The screen will display the ‘ENTER DATE’ window. Enter the date in the (YYYY/

MMM/DD) format. Select  to save. Date is now set.

The screen will display the ‘ENTER TIME’ window. Enter the time in the (HH.MM)

12 hour format followed by PM or AM. Select  to save. Time is now set.

Step 4: Set location

The screen will display the ‘SET LOCATION’ window. For this data entry, please

visit: www.whatsmygps.com to retrieve GPS location co-ordinates. Enter

address to nd the Decimal Degrees associated with GPS location. On the top

line of the Controller screen, enter the LATITUDE decimal degrees followed by

“N’ or ‘S’ (e.g. 123.4567° N). On the bottom line, please enter the LONGITUDE

decimal degrees followed by ‘W’ or ‘E’ (e.g. 333.4445° W).

Select  to save. Location is now set.

Step 5: Set Pin

The screen will display the ‘CREATE PIN’ window. Highlight OK in the enter PIN

window and enter the 4-digit PIN.

Note: We recommend choosing a number that can be easily remembered. It is important

to keep this PIN safe as it will be needed for most data entry. It is also advised that this PIN

is kept between managers/owners to avoid disruption to programs after set-up.

Select  to save. Pin is now created.

Step 6: Pair Lights

The next step is to pair the Stable Lights to the Controller. Select Pair Light icon

from the Main Menu. There are 5 options available to select; Paired, Pair, Un-

pair, Rename and Home. Select Pair icon. Enter PIN and select . The next

window will display ‘ENTER SERIAL NUMBER(S) TO PAIR EXISTING LIGHTS(S)’.

Highlight ‘NO’ and select (•).

The Controller now enters pairing mode and a 5 minute count down is initiated

on the screen. As the timer is counting down, press the silver button on top of

each Stable Light to establish a connection (hold silver button for 2 seconds

and release). The Stable Light will ash red and turn off when it has successfully

communicated with the Controller. The identication number for the paired

Stable Light will now appear on the Controller’s display. A new 5 minute

countdown commences once a Stable Light has been successfully paired.

Go to the next Stable Light and repeat until all Stable Lights appear on the

Controller’s display with their corresponding numbers. It is advised to pair lights

in order of stable arrangement in yard/barn.

Step 7: Program Lights

Stable Lights will not turn on until a program is loaded. From the Main Menu,

select the Program icon. Within this menu, the options are View (to view

previously loaded programs), Setup (to select a program for loading) and

Home (return to main menu).

To load new programs or change programs, select Setup and ‘ENTER PIN’. Enter

PIN and select . Stable Lights can be identied by their unique identication

number (available on door card). Highlight by selecting one or more Stable

Lights to be programmed. Select .

Note: To change the programs, override the existing program loaded.

A window will then display 5 options

• CIRCA ANNUAL

• LONG DAY

• SHORT DAY

• REFLECT (mimics environmental light cycle at location)

• ERASE (Removes previously loaded program and deactivates Stable Light)

Indice

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Lightolier

Lightolier LP200 Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente

Lightolier

Lightolier Lytespan 83ED17S Manuale utente

Lightolier

Lightolier Calculite CS8226 Manuale utente