Equinox Systems EQLED71 Manuale utente

ORDER CODE: EQLED71

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modifications to this equipment are not

subject to warranty.

Equinox Orbital Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modification to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to flammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualified engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature fluctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualified

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

Equinox Orbital Technical specifications

You should find inside the carton the following items:

1, Equinox Orbital Moving Head 2, Power cable 3, User manual

Technical Specifications:

DMX channels: 6/11 selectable

Operating modes: 1, Sound Activated

2, Auto Run

3, DMX

4, Master/slave

Ultra Bright 25W LED output

Colour wheel: 8 Colours + White

Gobo wheel: 7 Gobos + Open

4 Push button LED digital display

Beam angle: 15 degrees

Pan: 540˚, Tilt: 270˚

0-100% dimming + strobe function

IEC power in socket

3 pin XLR in/out sockets

Power consumption: 106W

Power supply: 240V - 50Hz

Dimensions: 275 x 225 x 400mm

Weight: 8.1Kgs

Overview

Control Panel Overview:

To access the control panel functions, use the four push buttons located under the LED display.

When a function is selected, the LED display will show the first available option for that particular

function. Use the “UP” and “DOWN” buttons to navigate through the options. Press the “ENTER”

button to select the menu function that is currently displayed to enable or disable the menu option.

To return to the previous menu or option without changing the value, press the “MENU” button.

User Menu Configurations:

Equinox Orbital Operation modes

11 channel DMX chart

Equinox Orbital DMX Chart

Channel

Value Function

0-255

0-13

14-27

28-41

42-55

56-69

70-83

84-97

98-111

112-127

128-190

191-255

0-9

10-19

20-29

30-39

40-49

50-59

60-69

70-79

80-99

100-119

140-159

160-179

180-199

200-219

220-255

128-191

Pan 540˚

Tilt 270˚

White

Yellow

Pink

Green

Purple

Blue

Lime Green

Orange

Red

Continuous forwards rotation (fast to slow)

Continuous backwards rotation (slow to fast)

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 1 + Shake effect (slow to fast)

Gobo 2 + Shake effect (slow to fast)

Gobo 3 + Shake effect (slow to fast)

120-139

Gobo 4 + Shake effect (slow to fast)

Gobo 5 + Shake effect (slow to fast)

Gobo 6 + Shake effect (slow to fast)

Gobo 7 + Shake effect (slow to fast)

Gobo wheel rotation (slow to fast)

Manual gobo rotation

Auto clockwise gobo rotation (fast to slow)

192-255 Auto anti-clockwise gobo rotation (slow to fast)

0-127

30-255 Pan/tilt movement speed (fast to slow)

11 channel DMX chart (cont..)

Equinox Orbital DMX Chart

Channel

Value Function

0-9

10-19

128-137

138-201

202-255

0-255

0-16

17-33

34-50

51-67

68-84

85-101

102-118

119-135

136-152

Shutter closed

Shutter open

Strobe 2 (slow to fast)

Shutter open

Dimmer 0-100%

Blackout with pan/tilt movement

Blackout with all internal wheels moving

Colour and gobo wheel reset

All motor reset

Built-in programme 1

Built-in programme 2

Built-in programme 3

Built-in programme 4

20-127 Strobe 1 (slow to fast)

153-169 Built-in programme 5

170-186 Built-in programme 6

187-203 Built-in programme 7

204-220 Built-in programme 8

No function

221-237 Built-in show 1

238-255 Built-in show 2

Fine control of pan movement

Fine control of tilt movement

6 channel DMX chart

Equinox Orbital DMX Chart

Further DMX cables can be purchased from all

good sound and lighting suppliers or Prolight

dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

DMX Control Mode

Operating in a DMX control mode environment gives the user the greatest flexibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of

the fixture and each fixture independently.

Setting the DMX address

The DMX mode enables the use of a universal DMX controller. Each fixture requires a

“start address” from 1- 511. A fixture requiring one or more channels for control begins to read the

data on the channel indicated by the start address. For example, a fixture that occupies or uses 7

channels of DMX and was addressed to start on DMX channel 100, would read data from

channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used

do not overlap. E.g. the next unit in the chain starts at 107.

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the

controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all fixtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX fixtures try to use the

shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The Equinox Orbital can be controlled via DMX-512 protocol. The DMX address is set on the

back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for

data input/output (figure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Equinox Orbital DMX set up

Notice:

• Be sure to follow figures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

Equinox Orbital DMX Set Up

Indice

Altri manuali Equinox Systems Proiettore

Equinox Systems

Equinox Systems EQLED020 Manuale utente

Equinox Systems

Equinox Systems EQLED041 Manuale utente

Equinox Systems

Equinox Systems Ripper EQLA27 Manuale utente

Equinox Systems

Equinox Systems SF-300 Manuale utente

Equinox Systems

Equinox Systems Fusion 50 Manuale utente

Equinox Systems

Equinox Systems EQLED76 Six Shooter Manuale utente

Equinox Systems

Equinox Systems Triclops Beam Manuale utente

Equinox Systems

Equinox Systems Revolution EQLED80 Manuale utente

Equinox Systems

Equinox Systems Fusion Razor Beam EQLED006 Manuale utente

Equinox Systems

Equinox Systems STRO11 Lightning Cracker Manuale utente

Equinox Systems

Equinox Systems EQLED002 Manuale utente

Equinox Systems

Equinox Systems Eclipse Manuale utente

Equinox Systems

Equinox Systems WATE03 Manuale utente

Equinox Systems

Equinox Systems LIGHTNING CRACKER 2 Manuale utente

Equinox Systems

Equinox Systems Ballero Spot Manuale utente

Equinox Systems

Equinox Systems Cabaret Colour Manuale utente

Equinox Systems

Equinox Systems EQLED65 Giga Bar System Manuale utente

Equinox Systems

Equinox Systems Crossfire EQLED061 Manuale utente

Manuali Proiettore popolari di altre marche

VIZULO

VIZULO Micro Martin Guida utente

EuroLite

EuroLite LED IP FL-100 SMD Manuale utente

Cooper Wheelock

Cooper Wheelock XB12 Manuale utente

Allen + Roth

Allen + Roth 17624-000 Manuale utente

ADJ

ADJ 4 STAGE PAK Manuale utente

Cooper Lighting

Cooper Lighting EGL91SW233 Manuale utente

Max

Max 37496 Manuale utente

BEGA

BEGA 85 143 Manuale utente

Beamz

Beamz 151.226 Manuale utente

EuroLite

EuroLite LED IP FL-8 Manuale utente

Ledj

Ledj PERFORMER 36 RGB Manuale utente

Perel

Perel ELS3 Manuale utente

Perel

Perel ELS3WD Manuale utente

LumX

LumX LM 36130 Manuale utente

Xtricity

Xtricity 4-80053 Manuale utente

Stahl

Stahl 6521/4 Series Manuale utente

Ecosense

Ecosense EcoSpec Manuale utente

Ayrton

Ayrton minipanel FX Manuale utente