Equipson Light Shark Series Manuale utente

V1.0

LS-WING

LS-Wing series user manual

By WorkPro

Equipson S.A.

No part of this manual, including the products or software described herein, may be reproduced, transmitted,

or translated into any language in any form or by any means without the express prior written consent of

Equipson S.A.

The guarantee of the product or service will not be extended if: (1) the product is repaired, modied or

altered, unless the repair, modication or alteration is authorized in writing by Equipson SA; (2) the serial

number of the product cannot be clearly read or is not present.

EQUIPSON SA PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTIES OF ANY KIND, EITHER

EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES, MARKET

CONDITIONS OR ADJUSTMENTS FOR ANY PURPOSE. IN NO EVENT SHALL EQUIPSON SA, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY DAMAGES, WHETHER

INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL (INCLUDING DAMAGES FOR LOSS OF

PROFITS, BUSINESS, LOSS OF USE OR DATA, BUSINESS INTERRUPTION OR THE LIKE), EVEN IF

EQUIPSON SA HAS BEEN ADVISED THAT THE POSSIBILITY OF SUCH DAMAGES MAY ARISE FROM

ANY DEFECT OR ERROR IN ITS MANUALS OR PRODUCTS.

THE SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FOR INFORMATIONAL

PURPOSES ONLY AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE AND MAY NOT

BE USED AS A COMMITMENT BY EQUIPSON SA. EQUIPSON SA ASSUMES NO RESPONSIBILITY FOR

ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE

PRODUCTS AND/OR THE SOFTWARE DESCRIBED IN IT.

The products and corporate names appearing in this manual may (or may not) be trademarks or copyrights

of their respective companies, and are used herein only for identication or explanatory purposes and for the

benet of the owner, without intent to infringe such standards.

Policy

This equipment complies with EMC Directive 2004/108/EC and LVD 2006/95/EC.

This product is approved by the following safety standards: EN 60950~1:2006 + A11:2009 + A1:2010 +

A12:2011 + A2:2013

AND EMC standards EN55022: 2010 EN61000-3-3: 2013 EN55020:2007+ A11 EN61000-4-2: 2009

EN61000-4-3: 2006 + A1+ A2

ATTENTION: Any modication or change made to this device, unless explicitly approved by Equipson SA,

will void the authorization to use this device.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.

For further details please contact: Equipson SA, AV El Saler nº14, Silla, Valencia, Spain. Telephone: +34

961 216 301 E-mail: [email protected]

1-Overview

1.1 About LS-Wing

1.2 Overview of the LS-Wing

2-First steps

2.1 Selecting the mode of use of the LS-Wing

2.2 Wing mode of the LightShark system

2.3 MIDI controller mode

2.4 MIDI notes

2.5 OSC/UDP controller mode

3-Access via web server

3.1 Connection options

3.2 Connecting from a mobile device

3.3 Connection from a PC

4-Settings

4.1 Device settings

4.2 Node Settings

5-OSC/UDP settings

5.1 Target Adjustments

5.2 Creating a Custom Mapping

6-Remote Control Settings

6.1 Remote control via OSC

6.2 Remote control via DMX

6.3 Assigning LS-Wing functions

7-Software and library updates

7.1 Updating libraries

7.2 Software update

7.3 Backup

8-Factory Reset

8.1 Reset modes

Section 1: Overview

1.1 About LS-Wing

LS-Wing is an innovative hardware offering several products in one: a Wing for LS-1 / LS-

Core, an OSC/UDP hardware controller and a MIDI controller.

LS-Wing can send/receive OSC commands over ethernet from any software or hardware

supporting this protocol. In addition, it can send/receive UDP messages, making it

compatible with any AV device or software on the market*.

LS-Wing offers exceptional versatility to the lighting control market, as it can be congured

to be compatible with other lighting systems. Developed as a 3-in-1 product, LS-Wing can

be a simple fader wing, an OSC hardware controller or a standalone MIDI console for any

device that accepts MIDI control via USB. A total of four USB ports are provided, including

a USB-B port, making it easy to connect to MIDI compatible devices and to charge smart

phones and tablets.

In addition, the LS-Wing has a built-in ArtNet-RDM/sACN to DMX node that offers

two direct DMX universes. Existing LightShark products - the LS-1 and LS-Core - already

offer two Direct DMX universes via an XLR connector, so by adding the LS-Wing it is very

easy to double the number of Direct DMX universes available on each console. Its 3-in-1

design makes it easily the most versatile and functional controller on the market. In

addition, lighting professionals working in theaters and live shows can have complete

control of more than one device at a time, just by using different pages in the same unit.

1.2 Overview of the LS-Wing

The LS-Wing control surface offers the user a control system with 10 Faders and a set of 60

RGB buttons.

Thanks to its small size, it can be transported as hand luggage. On the back, there is a

holder to hold devices such as tablets. In addition, it includes different USB ports, an

ethernet switch and 2 DMX outputs located on the back panel:

Layout

1Flash buttons

2Playback Faders

3Pause buttons

4Go Buttons

5Playback selection buttons

6Executor buttons

Rear Panel

1Connection port for 5v LLC-1 lamp ( XLR-3 )

2DMX outputs 1 and 2 (XLR-5 )

3Ethernet switch

42x USB type A ports for Data

52x USB type A ports for +5V DC

61x USB 2.0 type B port

7Power connection ( PowerCON TRUE 1 )

Dimensions (WxHxD): 325X100X330 mm

Weight: 2,7Kg

12 3 4 5 6 7

2.2 LightShark Wing Mode

In this mode the LS-Wing will work as a playback extender, both in the LS-1 and in the

LS_Core. The conguration of the Faders ands buttons in the Wing is the following:

Assigned to the rst 2 rows of buttons on page 1 of

the executors.

Assigned to the playback selection buttons.

Assigned to the Go buttons.

Assigned to the Pause buttons.

Assigned to the playbacks faders.

Assigned to the Flash Buttons.

The connection between the LS-1 and the LS-Wing is made via USB, by connecting the LS-

Wing to the "USB-Data" port of the LS-1.

The connection between the LS-Core and the LS-Wing is made via USB by connecting the

LS-Wing to the front "USB Host" port of the LS-Core.

Section 2: First Steps

2.1 Selecting the mode of use of the LS-Wing

It is possible to select the operation mode of the LS-Wing during system startup. Once the

power is turned on, the lower buttons will ash for 30s , during that time the user can

select the operating mode by pressing one of the buttons 1 to 5 in the PlayBack selection

area:

Key 1: LightShark Wing mode to control PlayBack 1 to 10.

Key 2: LightShark Wing mode to control PlayBack 11 to 20.

Key 3: LightShark Wing mode to control PlayBack 21 to 30.

Key 4: MIDI control surface mode.

Key 5: OSC/UDP control surface mode.

2.3 MIDI controller mode

In this mode, the LS-Wing will function as a MIDI control surface and can be used with any

program or device that supports this protocol.

The note assignment is as follows:

CH1

N10

CH1

N11

CH1

N12

CH1

N13

CH1

N14

CH1

N15

CH1

N16

CH1

N17

CH1

N18

CH1

N19

CH1

N20

CH1

N31

CH1

N32

CH1

N33

CH1

N34

CH1

N35

CH1

N36

CH1

N37

CH1

N38

CH1

N39

CH1

N40

CH1

N41

CH1

N42

CH1

N43

CH1

N44

CH1

N45

CH1

N46

CH1

N47

CH1

N48

CH1

N49

CH1

N50

CH1

N51

CH1

N52

CH1

N53

CH1

N54

CH1

N55

CH1

N56

CH1

N57

CH1

N58

CH1

N59

CH1

N60

CH1

N62

CH1

N63

CH1

N64

CH1

N65

CH1

N66

CH1

N67

CH1

N68

CH1

N69

CH1

N70

CH1

N71

CH1

N21

CH1

N22

CH1

N23

CH1

N24

CH1

N25

CH1

N26

CH1

N27

CH1

N28

CH1

N29

CH1

N30

2.4 MIDI notes

Element Channel Type Note Value

Executor Button 1-1 1 Note 1 OFF( 64 ) / ON ( 127 )

Executor Button 1-2 1 Note 2 OFF( 64 ) / ON ( 127 )

Executor Button 1-3 1 Note 3 OFF( 64 ) / ON ( 127 )

Executor Button 1-4 1 Note 4 OFF( 64 ) / ON ( 127 )

Executor Button 1-5 1 Note 5 OFF( 64 ) / ON ( 127 )

Executor Button 1-6 1 Note 6 OFF( 64 ) / ON ( 127 )

Executor Button 1-7 1 Note 7 OFF( 64 ) / ON ( 127 )

Executor Button 1-8 1 Note 8 OFF( 64 ) / ON ( 127 )

Executor Button 1-9 1 Note 9 OFF( 64 ) / ON ( 127 )

Executor Button 1-10 1 Note 10 OFF( 64 ) / ON ( 127 )

Executor Button 2-1 1 Note 11 OFF( 64 ) / ON ( 127 )

Executor Button 2-2 1 Note 12 OFF( 64 ) / ON ( 127 )

Executor Button 2-3 1 Note 13 OFF( 64 ) / ON ( 127 )

Executor Button 2-4 1 Note 14 OFF( 64 ) / ON ( 127 )

Executor Button 2-5 1 Note 15 OFF( 64 ) / ON ( 127 )

Executor Button 2-6 1 Note 16 OFF( 64 ) / ON ( 127 )

Executor Button 2-7 1 Note 17 OFF( 64 ) / ON ( 127 )

Executor Button 2-8 1 Note 18 OFF( 64 ) / ON ( 127 )

Executor Button 2-9 1 Note 19 OFF( 64 ) / ON ( 127 )

Executor Button 2-10 1 Note 20 OFF( 64 ) / ON ( 127 )

Flash Button 1 1 Note 21 OFF( 64 ) / ON ( 127 )

Flash Button 2 1 Note 22 OFF( 64 ) / ON ( 127 )

Flash Button 3 1 Note 23 OFF( 64 ) / ON ( 127 )

Flash Button 4 1 Note 24 OFF( 64 ) / ON ( 127 )

Flash Button 5 1 Note 25 OFF( 64 ) / ON ( 127 )

Flash Button 6 1 Note 26 OFF( 64 ) / ON ( 127 )

Flash Button 7 1 Note 27 OFF( 64 ) / ON ( 127 )

Flash Button 8 1 Note 28 OFF( 64 ) / ON ( 127 )

Flash Button 9 1 Note 29 OFF( 64 ) / ON ( 127 )

Flash Button 10 1 Note 30 OFF( 64 ) / ON ( 127 )

Playback Select Button 1 1 CC 31 0-127

Playback Select Button 2 1 CC 32 0-127

Playback Select Button 3 1 CC 33 0-127

Playback Select Button 4 1 CC 34 0-127

Playback Select Button 5 1 CC 35 0-127

Playback Select Button 6 1 CC 36 0-127

Playback Select Button 7 1 CC 37 0-127

Playback Select Button 8 1 CC 38 0-127

Playback Select Button 9 1 CC 39 0-127

Playback Select Button 10 1 CC 40 0-127

Go Button 1 1 CC 41 0-127

Go Button 2 1 CC 42 0-127

Go Button 3 1 CC 43 0-127

Go Button 4 1 CC 44 0-127

Go Button 5 1 CC 45 0-127

Go Button 6 1 CC 46 0-127

Go Button 7 1 CC 47 0-127

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Equipson Controllori

Equipson

Equipson Work Pro WGC1 MKII Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente