Erco Compact IP65 Manuale utente
3000042822
0217
EERCO GmbH
Postfach 2460
58505 Lüdenscheid
Brockhauser Weg 80-82
58507 Lüdenscheid
Germany
Tel.: +49 2351 551 0
Fax: +49 2351 551 300
www.erco.com
Compact IP65
Mounting instructions
1
23000042822
English
Read the instructions carefully
before installation and com-
missioning!
Leave the instructions for
users/customers for future
reference!
Our updated product documen-
tation can be accessed at
www.erco.com/download.
General safety information
Warning!
Risk of electric shock!
Before carrying out maintenance and
installation on the luminaire, discon-
nect from the mains supply and ensure
that all power is switched off.
Attention!
- Do not open the luminaire head. In
case of damage or a defective LED
module, the entire luminaire must be
returned to the factory.
- Do not operate luminaires with dama-
ged or missing safety glass.
- When installing, always observe the
national installation and accident pre-
vention regulations.
Intended use
The luminaire is suitable for both out-
door and indoor use.
Choosing the mounting location
Luminaire not suitable for covering
with thermal insulation material.
- Lateral air space under EN 60598:
The lateral distance between the surface
of the luminaire and any parts of the
building must be no less than 50mm.
- Recess depth under EN 60598:
No minimum distance is required bet-
ween the uppermost surface of the
luminaire and any parts of the building.
- Position the luminaire so as to avoid
operation in direct sunlight or near
other sources of heat. High ambient
temperatures can reduce the life and
efficiency of the control gear or LED
module.
Electrical installation
- The connector is prepared for
through-wiring (looping in).
- For 3-circuit installation: to avoid any
damage to the control gear, the neutral
conductor must never be connected or
disconnected during operation.
Overvoltage protection
ERCO uses electronic control gear with
overvoltage protection in accordance
with DIN EN 61547. If additional protec-
tion from spikes is required, e.g. when
switching off inductive loads, separate
overvoltage protection units should be
installed.
Notes on corrosion protection
Ensure that the powder coating is not
damaged during installation or mainte-
nance work. Any damage, which becomes
wet, can result in corrosion occurring. In
aggressive environments, the installation
and maintenance of all parts will require
the appropriate protective measures. Che-
micals damage the corrosion protection.
Rotating oval flood
The oval flood characteristic is rotated
by positioning the whole luminaire. Dis-
mount the luminaire and adjust before
reinstalling it.
Flashing of the LED module
It is normal for the LED module to
flicker when switching on and off.
Dimming
Depending on the model, the luminaire
can be dimmed using a suitable dimmer
(trailing edge).
Trailing-edge dimmers
Follow the manufacturer’s installation
instructions. For some products, the lumi-
naire can only be switched on in the
upper dimming range. Before installation
and connection, check luminaire, control
gear and dimmer combination for proper
functioning of the dimmer, especially
when using universal dimmers.
The use of dimmers which are unsuitable
for LED drivers can damage the lumi-
naire, control gear and/or the dimmer.
No responsibility is accepted for the
use of dimmers that are unsuitable for
the luminaire.
Cleaning
Always clean carefully using a soft
cloth and a commercially available,
ph-neutral, alcohol-free, non-abrasive
cleaning agent.
Take care not to damage the powder-
coating.
Cleaning the safety glass
Safety glass can be cleaned with clea-
ning agents that are also suitable for
glass-ceramic cooking hobs.
Disposal
In accordance with EU Directive
WEEE (Waste Electrical and Electro-
nic Equipment), luminaires must not
be disposed of with other household
waste. At the end of their life, lumi-
naires must be taken to the appropriate
local facility available for the disposal
or recycling of electronic products.
Altri manuali Erco Lanterna
