ErgoSafe ClickitUp CiU Fixed Manuale utente
Instruction Manual
CiU®Fixed
by
ClickitUp®has a design and construction that is new on the market and the product is design protected by Ergo-
Safe AB.AB. Design right 002416248. 001-005. 3/3 2014
Contents
Safety........................................................................................................................................3
Reception - unloading ......................................................................................................................3
Installation .......................................................................................................................................4
Preparations prior to installation ......................................................................................................... 4
Installation.........................................................................................................................................5
Technical specication ........................................................................................................................ 6
Use ...................................................................................................................................... 7
Warranty.............................................................................................................................................7
Troubleshooting.......................................................................................................................................7
Dismantling .................................................................................................................................... 7
3
ErgoSafe AB | Reparatörgatan 1 | SE-302 62 Halmstad | +46 (0)10-480 47 00 | www
.ergosafe
.se
by
Reception - unloading
ON DELIVERY
A delivery inspection of CiU Fixed should be performed in order to discover and transport damage
or other defects on the packaging and/or product. Any delivery damage must be noted on the shipping
company’s consignment note and ErgoSafe must be notied at the latest one week after receipt of the
delivery. Thereafter, it is not possible to cite discrepancies regarding the delivery of CiU Fixed.
UNLOADING FROM PALLETS
Note that unloading must be performed in a specic order, otherwise personal injury can occur.
There is also a risk of product damage. Set the pallets on a at surface.
1. Start by removing the packaging plastic
2. Then lift o the sections that are to be installed from pallets
3. Remember to secure the sections remaining on pallets so these do not fall
Each section is individually secured on the packaging to
prevent CiU Fixed from falling during unloading.
Loosen the straps gradually as CiU Fixed sections
are installed. Each package can hold up to 6 CiU Fixed
sections.
Safety
GLASS
The glass is safety glass - toughened.
by
4
ErgoSafe AB | Reparatörgatan 1 | SE-302 62 Halmstad | +46 (0)10-480 47 00 | www
.ergosafe
.se
Preparations prior to installation
Below follows a description of what is important to remember when installing CiU Fixed. Read
through the manual before starting to install CiU Fixed .
Each CiU Fixed section is delivered ready-assembled. Sections are linked together to form a system
with the help of double top caps and double baseplate mounts.
The substrate must be dimensioned according to applicable standards. When fastening to concrete
CiU Fixed must be installed with sheet rubber against the concrete surface.
CiU Fixed is delivered complete with top caps and baseplate mounts, single or double depending
on what is specified on the order. During transport the section/sections are fitted with transport top
caps.
Installation
6 screws per section are supplied, intended to
secure installed ClickitUp®sections.
Note! Screws for fastening in the substrate
are not included.
Single top cap with 2 screws
Post
Foot
Fixed glass
5
ErgoSafe AB | Reparatörgatan 1 | SE-302 62 Halmstad | +46 (0)10-480 47 00 | www
.ergosafe
.se
by
2. Install all sections
Set out the other sections. Continue as per the same principle until all sections are in position.
Installation
1. Install the rst section
Set out a straight line where CiU Fixed is to be installed. Note that if the ground slopes the posts
will be in their bottom position at the ground’s highest point. Any adjustments are made as per
figure 3. If corners are to be installed, start with this. Place the rst section on the baseplate mounts.
Use the fastening fittings on the baseplate mounts that are designed for the glass balustrades
substrate. ErgoSafe encourages CiU Fixed/Balcony to be fastened to a stable substrate, concrete
ortimber joists. Once the rst section is in position, prepare single/double mounts for the next section.
by
6
ErgoSafe AB | Reparatörgatan 1 | SE-302 62 Halmstad | +46 (0)10-480 47 00 | www
.ergosafe
.se
Technical specification
Description Glass balustrade
Safety The glass is safety glass - toughened.
Manufacturing
method
Structural glazing is used to t the glass to the aluminium posts
Baseplate mounts As standard there are baseplate mounts which are double, single and side
baseplate mounts.
Top caps Top caps are available as double and single mounts
Material Glass, aluminium and stainless steel
Glass Toughened glass 8 mm
Height 1100 mm
Width straight
section
Max 1800 mm
Surface treatment Natural anodised as standard. As an option at an additional charge, black ano-
dised or powder coated in an RAL colour (only xed posts)
7
ErgoSafe AB | Reparatörgatan 1 | SE-302 62 Halmstad | +46 (0)10-480 47 00 | www
.ergosafe
.se
by
Warranty
In order for the warranty to be valid the conditions A-C must be met:
A: When invoking the warranty, the seller must be contacted to assess the complaint with regard to the
warranty. The seller must confirm that the fault is of such a nature that it is covered by the warranty.
All interventions or measures on the product that do not go through ErgoSafe’s complaints depart-
ment invalidate the warranty and are entirely the responsibility of the person who has performed or
ordered the work.
B: When invoking the warranty, the product’s serial number must be stated as well as any pictures that
clarify what is being claimed on the warranty.
C: When exchanging parts, these must unconditionally be returned to the seller. If this does not
occur, the customer loses the right to warranty compensation.
The warranty does not cover: Incorrect installation or a settlement in the ground or timber struc-
ture.
Dismantling
When dismantling CiU Fixed
Note!
Risk of cuts
Exercise care when handling glass. The product consists of thermally tempered glass that, in the
event of incorrect handling, can break and cause injuries.
MATERIAL RECYCLING
All metals are sorted in containers for metal.
Plastic and rubber are sorted as inammable materials.
Glass is sorted as lling material.
Use
MAINTENANCE
In order for stainless steel details (the top cap) to maintain their appearance they should be polished
annually.
ErgoSafe AB | Reparatörgatan 1 | SE-302 62 Halmstad | +46 (0)10-480 47 00 | www.ergosafe.se
Copyright © 2015 ErgoSafe AB.
Indice
Altri manuali ErgoSafe Recinzioni e cancelli
