Erreka GLOBAL 4 Manuale utente
GLOBAL 4 SYSTEM
TELESCOPIC 4 SYSTEM
ACTUATOR FOR SLIDING DOORS
INSTALLATION MANUAL
1
INTRODUCTION
ERREKA Automatic Doors thanks you for the trust placed in us and for having selected a product that we manufacture.
We recommend detailed reading of this installation manual for proper assembly, the performance of your automatic door
will depend on the quality of your work.
ERREKA Automatic Doors will not be held liable for any damages caused by an installation not in accordance
with this Installation Manual.
Revisión
nº
Date
Modifications
05 18/03/20
GLOBAL 4 operator ( HW v. 2.6 )
( SW v 1.0.17)
CONTENTS
1.
WARNING FOR INSTALLER................................................................................................................................2
2.
EC CONFORMITY STATEMENT..........................................................................................................................2
3.
TOOL KEY............................................................................................................................................................2
4.
ELECTRIC PRE-INSTALLATION..........................................................................................................................3
5.
TECHNICAL FEATURES......................................................................................................................................3
6.
GLOBAL ASSEMBLY............................................................................................................................................4
7.
TELESCOPIC ASSEMBLY .................................................................................................................................14
8.
CONTROL BOARD CONNECTION ....................................................................................................................27
9.
SET UP..............................................................................................................................................................42
10.
PARAMETER ADJUSTING FROM SELECTOR............................................................................................. 44
11.
TROUBLESHOOTING GUIDE .......................................................................................................................51
12.
ANNEXES......................................................................................................................................................53
2
1. WARNING FOR INSTALLER
Importance of this manual
- Before installing, please read this manual and follow all instructions. Otherwise, the installation may be faulty and may
cause accidents and breakdowns.
- ERREKA Automatic Doors will not be held liable for any damages caused by an installation not in accordance with this
Installation Manual.
Projected Usage
- This product has been designed to be installed as part of automatic opening and closing sliding pedestrian doors. It is
designed for intensive use within the weight limits indicated on the characteristics. Installation and use is indicated to
use inside buildings.
- Any use for any purpose other than indicated is considered inadequate and therefore dangerous.
Safety elements
- The unit meets all current safety standards. Follow the instructions of all the elements fitted in the installation.
- Erreka Automatic Doors doesn´t accept any responsibility for the safety and smooth operation of the door when using
system components other than those produced by Erreka.
2. EC CONFORMITY STATEMENT
Manufacturer: MATZ ERREKA, S. Coop.
B º San Juan 93
20570 Bergara (GUIPUZCOA) - SPAIN
Product: Operator for automatic sliding door ERTAIN 4
States that: The operator has been constructed to be incorporated into the machinery or to be assembled with
other elements to create a machine under the following guidelines and standards:
●Machinery Directive 2006/42 CE
●EMC Directive 2004/108/CE
●Low Voltage Directive 2006/95/CE
●Power operated pedestrian doorsets – safety in use, requirements and test methods: EN 16005
3. TOOL KEY
DRIL
∅
∅∅
∅
7DRILLBIT
∅
∅∅
∅
8.5DRILLBIT
CROSSHEADSCREWDRIVER
FLATSCREWDRIVER
SPIRIT
LEVEL
Nº13SPANNER
Nº13SOCKET
WRENCH
M8BOLT
Nº10SPANNER
Nº4T-HANDLEALLEN
WRENCH
CLAMP
WIRESTRIPPER
3
4. ELECTRIC PRE-INSTALLATION
5. TECHNICAL FEATURES
CHARACTERISTICS G4 - Operator 870 T4- Operator 870
Clearway (2 sliding-leaves / 4 sliding leaves) 1000-3000mm 1000-3000mm
Clearway (1 sliding-leaf / 2 sliding leaves) 750-3000mm 750-3000mm
Maximum weight per leaf (2 leaves / 4 leaves) 140 + 140 Kg. 70 +70+70+70 Kg
Maximum weight per leaf (1 leaf / 2 leaves) 200 Kg. 100+100 Kg.
Opening speed 0.2-0.8 m / s 0.2-0.8 m / s
Closing speed 0.1- 0.5 m/s 0.1- 0.5 m/s
Maximum closing force 150 N 150 N
Temperature -20ºC/ +50ºC -20ºC/ +50ºC
Door open timing 60 sec. 60 sec.
Power Supply * 230 V ~ (± 10 %) / 50 Hz 230 V ~ (± 10 %) / 50 Hz
Consumption 200 W 200 W
Batteries Ni Cd (24 v) Ni Cd (24 v)
* Available upon request, the version of the operator for the supply of: 110 V ~ (± 10 %) / 60 Hz
Nº DESCRIPTION CABLES
1 Power supply
3 wire hose (2,5mm
2
)
2
Selector ( Bus CAN) 4 shielded wires
(0,5mm
2
)
3
Externak key KC y KB 3 wires (0,5mm
2
)
4
Activation sensors+ photocell 8+8 wires (0,5mm
2
)
5
Safety sensors 6+6 wires(0,5mm
2
)
4
6. GLOBAL ASSEMBLY
This section explains in detail how to perform the installation mounting. For your information the following shows a
diagram of the profiles and external dimensions of the motorization.
1.- Perfil Caja.
2.- Perfil Tapa.
3.- Goma antivibración.
4.- Junquillo Caja.
5.- Junquillo Tapa.
12
3
4
5
165
160
54
17
70
5
1.- Support Profile.
2.- Cover Profile.
3.- Anti-vibration rubber band.
4. Support bead.
5. Cover bead.
5
6.1 Measuring the structure beforehand
Measure the dimensions of the gap where the door will be installed:
- Clearance height (H)
- Total width (B)
- Define what the Clearway (LUP) is, the Clearance Height Width of the fixed leaves
(FW), and the length of the support profile (B).
B=2xLUP+2xSC +100
6.2 Fitting the support profile
Variantes de colocación del Perfil Caja;
1.- Wall or UPN
120
98
60
160
165
160
65
2.- Erreka lintel – self supporting beam 1
60 98
120
160
165
160
60
3.- Erreka lintel – self supporting beam 2
60
160
165
160
120
98
60
Pasos a seguir;
1.- Mark the installation height of the support
profile. The profile must be set at 35mm from the
base of the beam (wall / structure).
2.- Place side covers, fixing them to the support
profile with ∅4.2x13 screws. Place the rubber (on
the entire length) in the support profile.
Rubber
3.- Make holes in the support profile on the marking
lines.
20
max. 3m
4.- Fit the profile in the correct position and drill
holes in the beam.
5.- In accordance with the characteristics of the
beam:
- Screw the holes for fixing the profile with M8
screws.
- Place anchors bolts to fix with spits.
- Fix the support with a special tapping screw.
6.- Secure the support profile. Make sure the profile
is levelled.
SCSC
FW
LUP
FW
H
B
6
6.3 Fitting the support bead
- Insert the brush into the slot of the support bead.
- Each 1 meter, make drill holes in the support bead.
- Place an M6x16 screw in each holes DIN 7984 and an extended nut. Place the bead in the support profile and tighten
the screws, place the extended nuts in the direction of the support profile track, move the screws up until they stop and
turn them clockwise.
6.4 Positioning the carriages on the rail
- With a size 4 Allen wrench loosen the half-way wheel (anti-derailing
wheel) and move to the lowest position of the slot.
- Put the carriage above the carriageway of the support profile.
- Once the carriage is on track, move the anti-derail wheel up and
secure it.
6.5 Place the fixed leaves
- Attach the fixed leaves, in accordance with the
manual of the profile to be installed.
- For fixed leaves with Fine and Gripper profile
use the bridles to attach the fixed leaves to the
Support bead!
Ertain Carrier
Anti-derailing wheel
Anti-derailing wheel
7
6.6 Fasten the hangers to the mobile leaves
- Secure the hangers on the sliding leaves as in the drawing, the
centre of the attack must be approx. 130 mm from the sides of the
moving sheet.
- Fasten the M8x25 screws with a size 13 wrench (2 per attack).
- For all profiles, make the holes at the following measurements at
the 2 ends.
130
74
92
92
82
130
-
With a sliding leaf and electrolock, the centre of the attack must
be approx. at 175mm.
6.7 Hang the leaves on the carriages
- Secure the attacks on the carriages with M6x16 Allen
screws, the toothed washers and flat washers.
6.8 Depth adjustment of the sliding leaves
- Use a size 13 wrench to position the moving leaf
parallel to the box profile, then measure the
distance between the leaf and the beam or the wall.
Put the 2 ends of the sheet at 5 mm.
3022
8
6.9 Fitting the Guide
- Move the sliding leaf to find an angle of 90º degrees, to do so use
a level.
- At this point, position the guide on the ground at the end of the
fixed leaf, with the block inserted into the sliding leaf guide, mark
the ground when the blade is level.
- Then secure the guide to the ground and slide the leaf over the
guide.
6.10 Height Adjustment of the Leaves
- Adjust the leaf height using the central screw of the carriage. This regulation is
very important, the leaves must be parallel when they meet.
6.11 Placing the limit switch
- Place a limit switch where the moving blades meet, to do so insert 2 long nuts on the rail and fasten the limit switch
stop with M6x10 Allen screws.
- The other limit is placed on one side.
90°
Regulation screw
Tope lateral
9
6.12 Preparation of wiring
- It is ADVISABLE to pass peripheral device wiring (photocells, radars, selector, etc.) before placing the motorization, as
afterwards there is little room for your hands. Try to pass them to the positioning height of the frame to make it easier
afterwards the connection to the frame. Use grommets to attach the cables, which are supplied and placed in the
support profile (see the picture below).
Wires
WIRING POSITION
6.13 Attaching the arms of the carriages
2 Sliding leaves
- Fix the separating nuts with DIN 7984 M6x16 allen screw and splined washer
using a wrench nº10.
- The arms must be installed as follows: the right arm in the up position (inside
right carrier) and left in the down position (inside left carrier.)
Use a screwdriver to remove the grommet!
Left inner carrier
Right inner carrier
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Erreka Controllori
Erreka
Erreka LINCE LIS424 Guida utente
Erreka
Erreka V2 CICLON Manuale utente
Erreka
Erreka ERTAIN 4 SYSTEM Manuale utente
Erreka
Erreka ERGOS Series Manuale utente
Erreka
Erreka AZIMUT Manuale utente
Erreka
Erreka VIVO-M201 Guida utente
Erreka
Erreka VIVO-M203 Istruzioni operative
Erreka
Erreka ROLL 60C Manuale utente
Erreka
Erreka VIVO-M101 Guida utente
Erreka
Erreka VULCAN Guida utente
