ESAB Caddyt Tig 150i Manuale utente

Valid for serial no. 620--xxx--xxxx0459 262 201 060523

Tig 150i

Tig 200i

OrigotTA33

Instruction manual

-- 2 --

TOCe

Rights reserved to alter specifications without notice.

1 DIRECTIVE 3........................................................

2SAFETY 3...........................................................

3 INTRODUCTION 5...................................................

3.1 Equipment 5................................................................

4 TECHNICAL DATA 5.................................................

5 INSTALLATION 6....................................................

5.1 Placing 6...................................................................

5.2 Rating plate 6...............................................................

5.3 Mains power supply 7........................................................

6 OPERATION 8.......................................................

6.1 Connections and control devices 8............................................

6.2 Control panel TA33 9........................................................

6.3 Overheating protection 9.....................................................

7 WELDING 10.........................................................

7.1 TIG welding 10...............................................................

7.2 MMA welding 12.............................................................

8 MAINTENANCE 12....................................................

9 FAULT TRACING 13...................................................

9.1 Fault codes 13...............................................................

10 ORDERING SPARE PARTS 13..........................................

DIAGRAM 14............................................................

DIAGRAM 16............................................................

ORDERING NUMBER 18.................................................

ACCESSORIES 19.......................................................

-- 3 --

bt26d2e

1DIRECTIVE

DECLARATION OF CONFORMITY

ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that weld-

ing power source Tig 150i / Tig 200i from serial number 620 complies with standard IEC/EN 60974--1

/--3, in accordance with the requirements of directive (73/23/EEC) and addendum (93/68/EEC) and

with standard IEC/EN 60974--10 in accordance with the requirements of directive (89/336/EEC) and

addendum (93/68/EEC).

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

Kent Eimbrodt

Global Director Equipment and Automation

ESAB AB

695 81 LAXÅ

SWEDEN Tel: + 46 584 81000 Fax: + 46 584 411924

Laxå 2006--05--22

2SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment

observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of welding

equipment. The following recommendations should be observed in addition to the standard regulations that apply to the work-

place.

All work must be carried out by trained personnel well--acquainted with the operation of the welding equipment. Incorrect oper-

ation of the equipment may lead to hazardous situations which can result in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

Sits operation

Slocation of emergency stops

Sits function

Srelevant safety precautions

Swelding

2. The operator must ensure that:

Sno unauthorized person is stationed within the working area of the equipment when it is started up.

Sno--one is unprotected when the arc is struck

3. The workplace must:

Sbe suitable for the purpose

Sbe free from drafts

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame--proof clothing, safety gloves.

SDo not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become trapped or cause burns.

5. General precautions

SMake sure the return cable is connected securely.

SWork on high voltage equipment may only be carried out by a qualified electrician.

SAppropriate fire extinquishing equipment must be clearly marked and close at hand.

-- 4 --

bt26d2e

WARNING

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU-

TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE

BASED ON MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK -- Can kill

SInstall and earth the welding unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS -- Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

SProtect your ears. Use earmuffs or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION -- Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

ESAB can provide you with all necessary welding protection and accessories.

WARNING!

Read and understand the instruction manual before installing

or operating.

Do not use the power source for thawing frozen pipes.

WARNING!

This product is solely intended for arc welding.

Do not dispose of electrical equipment together with normal waste!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical equipment

that has reached the end of its life must be collected separately and returned to an

environmentally compatible recycling facility. As the owner of the equipment, you should

get information on approved collection systems from our local representative.

By applying this European Directive you will improve the environment and human health!

-- 5 --

bt26d2e

3 INTRODUCTION

The Tig 150i/Tig 200i is a welding current power source intended for use with

coated electrodes (MMA welding) and TIG welding.

3.1 Equipment

The Tig 150i/Tig 200i is supplied with a mains cable and an instruction manual.

ESAB’s accessories for the product can be found on page 19.

4 TECHNICAL DATA

Tig 150i Tig 200i

Mains voltage 230V, 1∼50/60 Hz 230V, 1∼50/60 Hz

Fuse (delayed--action) 16 A 20 A

Primary current Imax 36 A 36 A

Primary current Ieff 21 A 21 A

Voltage/current range

(TIG)

(MMA) 3 A / 10 V --150 A / 16 V

4 A / 20 V --150 A / 26 V 3 A / 10 V -- 200 A / 18 V

4 A / 20 V -- 150 A / 27 V

Maximum permissible load at TIG

25% duty cycle

35% duty cycle

60% duty cycle

100% duty cycle

150 A / 16 V

120 A / 15 V

95 A / 14 V

200 A / 18 V

180 A / 17 V

140 A / 15,5 V

110A/14,5V

Maximum permissible load at MMA

25% duty cycle

35% duty cycle

60% duty cycle

100% duty cycle

150 A / 26 V

140 A / 25,5 V

110A/24,5V

90 A / 23,5 V

150 A / 26 V

140 A / 25,5 V

110A/24,5V

90 A / 23,5 V

Power factor at maximum current 0,62 0,62

Efficiency at maximum current 77 % 79 %

Open--circuit voltage 71 -- 78 V 71 -- 78 V

Operating temperature -- 1 0 ˚C--+40˚C-- 1 0 ˚C--+40˚C

Constant A--weighed sound pressure <70 db <70 db

Dimensions, l x b x h 380 x 180 x 300 mm 380 x 180 x 300 mm

Weight 9kg 9kg

Enclosure class IP 23C IP 23C

Application class

Duty cycle

The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-

tain load without overloading.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

-- 6 --

bt26d2e

4.1 Parameter setting

Settings Setting range In steps of: Default value

Welding method TIG or MMA -- TIG

2/4--stroke 2strokeor4stroke -- 2--stroke

HF / Lift ArctHF or LiftArct-- HF

Slope down time 0--10 s 0.1 s 1.0 s

Gas post--flow 0--25 s 0.1 s 2.0 s

Current TIG Tig 150I 3 -- 150 A 1A 100 A

Current TIG Tig 200I 3 -- 200 A 1A 100 A

Current MMA Tig 150I 3 -- 150 A 1A 60 A

Current MMA Tig 200I 4 -- 150 A 2A 100 A

5 INSTALLATION

The installation must be executed by a professional.

WARNING!

This product is intended for industrial use. In a domestic environment this product may cause radio

interference. It is the user’s responsibility to take adequate precautions.

Note!

Connect the power source to the electricity mains with a network impedance of 0.210 ohm or lower. If the

network impedance is higher, there is a risk of flicker in the illuminators.

5.1 Placing

Place the power source so that its cooling air inlets and outlets are not obstructed.

5.2 Rating plate

The rating plate is located on the underside of the power source or on the rear plate.

-- 7 --

bt26d2e

5.3 Mains power supply

Make sure that the welding power source is connected to the correct supply voltage

and that it is protected by the correct fuse rating. The standards for the country in

question must be complied with as regards the mains cable area. A protective earth

connection must be made in accordance with regulations.

5.3.1 Recommended fuse sizes and minimum cable areas

Tig 150i Tig 200i

Mains voltage 230 V ¦10 %, 1--phase 230 V ¦10 %, 1--fas

Mains frequency 50--60 Hz 50--60 Hz

Fuse (delayed--action)

85A 35% duty cycle MMA

120A 20% duty cycle MMA

150A 25% duty cycle MMA

10 A

16 A

20 A*)

10 A

16 A

20 A

Mains cable, area 3x2.5mm

23x2,5 mm2

Welding cable, area MMA 16 mm216 mm2

Welding cable, area TIG 16 mm225 mm2

*) NOTE! The mains plug is approved for maximum 16A.

North American version: Mains cable is approved for maximun 18 A.

Australian- version: The mains cable plug is approved for maximum 15A.

Note!

The cable area and fuse rating above comply with Swedish regulations. Use the welding power source

in accordance with the relevant national regulations.

-- 8 --

bt26d2e

6 OPERATION

General safety regulations for the handling of the equipment can be found on

page 3. Read through before you start using the equipment!

6.1 Connections and control devices

Make sure that the welding power source is connected to the correct supply voltage

and that it is protected by the correct fuse rating.

1Mains switch 6TIG torch connection (--)

2Connection (gas bottle connector) 7Connection for return cable (--) MMA

3Mains cable 8Welding cable connection (+) MMA

Connection for return cable (+) TIG

4Connection for the TIG torch 9Control panel (see 6.2)

5TIG torch gas connection

7and 8are used for welding current supply and return cable connection during MMA

welding

-- 9 --

bt26d2e

6.2 Control panel TA33

The power source checks the LEDs and all segments in the display when main

switch is turned on. The machine type and program version are also displayed.

AMains voltage (green) LED BData display

COverheating (yellow) LED DKnob for setting data.

Increase (+) or Decrease (--) selected by

the function pushbuttons

6.2.1 Panel function symbols (E -- G)

TIG TIG HF 2--stroke

MMA LiftArct4--stroke

GSlope down F. Gas post--flow

6.3 Overheating protection

The welding power source has a thermal overload trip which operates if the

temperature becomes too high, interrupting the welding current and lighting a

yellow indicating lamp on the front of the power source. The thermal overload trip

resets automatically when the temperature has fallen.

7 WELDING

7.1 TIG welding

During TIG welding, the return cable must be connected to (+) and the TIG torch to

(--). If they are connected in reverse, the tungsten electrode will melt.

-- 1 0 --

bt26d2e

7.1.1 2--stroke

Gas pre--flow Slope

up Slope down Gas post--flow

Functions when using 2--stroke control of the welding torch.

In the 2--stroke control mode, pressing the trigger switch starts gas pre--flow (if

used) and strikes the arc (1). The current rises to the set value (as controlled by the

slope up function, if in operation). Releasing the trigger switch (2) reduces the

current (or starts slope down if in operation) and extinguishes the arc. Gas

post--flow follows if it is in operation.

7.1.2 4--stroke

Gas pre--flow Slope

up Slope down Gas post--flow

Functions when using 4--stroke control of the welding torch.

In the 4--stroke control mode, pressing the trigger switch starts gas pre--flow (if

used) (1). At the end of the gas pre--flow time, the current rises to the pilot level (a

few ampere), and the arc is struck. Releasing the trigger switch (2) increases the

current to the set value (with slope up, if in use). At the end of welding, the welder

presses the trigger switch again (3), which reduces the current to pilot level again

(with slope down, if in use). Releasing the switch again (4) extinguishes the arc and

starts gas post--flow.

7.1.3 HF

The HF function strikes the arc by means of a spark from the tungsten electrode to

the workpiece as the electrode is brought closer to the workpiece.

Altri manuali per Caddyt Tig 150i

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ESAB Sistema di saldatura

ESAB

ESAB Buddy Arc 145 Manuale utente

ESAB

ESAB Caddy Arc 151i Manuale utente

ESAB

ESAB Origo Mig 4002c Manuale utente

ESAB

ESAB Aristo Origo Feed 3004 Manuale utente

ESAB

ESAB MEK 4 Manuale utente

ESAB

ESAB Buddy Arc 200 Manuale utente

ESAB

ESAB DTB 250 Manuale utente

ESAB

ESAB LKB 265 Manuale utente

ESAB

ESAB Cutmaster 40 SL60 1Torch Manuale utente

ESAB

ESAB Origo Tig 3001i Manuale utente

ESAB

ESAB Origo Mag C140 Manuale utente

ESAB

ESAB Origo Mig C141 Manuale utente

ESAB

ESAB Aristo Mig 5000i 460 V Manuale utente

ESAB

ESAB LKB 400W Manuale utente

ESAB

ESAB MEK 4C Manuale utente

ESAB

ESAB OCE 2H Manuale utente

ESAB

ESAB PowerCut 700 PT-39 Manuale utente

ESAB

ESAB LHF 400 Manuale utente

ESAB

ESAB PT-25 Manuale utente

ESAB

ESAB LHJ 750 Guida

ESAB

ESAB TXH Series Manuale utente

ESAB

ESAB A6 TFD1 Manuale utente

ESAB

ESAB Migmaster 300i cvcc Manuale di installazione e d'uso

ESAB

ESAB Precision Plasmarc Manuale del proprietario

Manuali Sistema di saldatura popolari di altre marche

Berner

Berner PLASMACUT 54 Manuale utente

Pro Spot

Pro Spot PR-155 Manuale utente

Forney

Forney 210 Manuale utente

Thermal Arc

Thermal Arc 400S Manuale utente

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuale utente

GYS

GYS PROTIG 201 AC/DC Manuale utente

TAFA

TAFA 30*8B35 Manuale utente

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuale utente

CIGWELD

CIGWELD 636804 Guida rapida

Red-D-Arc

Red-D-Arc DC-400 Manuale utente

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuale utente

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuale utente

WIA

WIA Weldmatic 270 CP132-2 Manuale utente

Sonics

Sonics H520T Manuale utente

Miller

Miller Big Blue 400D Manuale utente

NewArc

NewArc RT2000 Guida rapida

Hypertherm

Hypertherm powermax1000 Manuale utente

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuale utente