ESCALADE Mizerak P0900 Manuale utente
1
U N I V E R S A L B I L L I A R D
A C C E S S O R Y D R A W E R
P0900-00
2014 Escalade Sports
MODEL NO.
P0900
A S S E M B L Y I N S T R U C T I O N S
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
2
Contact Escalade® Sports customer service department at:
Phone: 1-800-467-1245 Toll – Free !
Fax: 1-866-873-3533 Toll – Free !
E-mail: Pooltables@escaladesports.com
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering
parts.
3. To make assembly easier, use the Hardware Identifier on page 3 to identify and sort all fasteners. Check all cartons for kits. All
hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and parts
may not easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.
5. Tools required for assembly: Tape Measure, Carpenter’s Square, Sharpie Marker, one 5/16” Wrench or 8 mm Wrench, 7/64” Drill Bit and
Cordless Drill. Note: Ratchet and Socket can be substituted for open end wrenches. A portable light or lamp is also helpful to see under table.
6. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for
replacement parts.
Please Do Not Return This Product To The Store!
Please visit our Website at:
www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE®
SPORTS PRODUCT INFORMATION
P R E - A S S E M B L Y T I P S
2014 Escalade Sports
A S S E M B L Y T I P S
3
Drawer, Billiard Accessory
Hanger
Connector
Mounting Rail
Mounting Frame
Drawer Decal Sheet
#10 X 1" Long, Hex Washer Head Sheet Metal Screw
#8-32 Serrated Flange Hex Nut
Instruction Manual
P0900-P1
P0900-P2
P0900-P3
P0900-P4
P0900-P5
P0900-P6
P0900-H1
P0900-H2
P0900-M1
P1
P2
P3
P4
P5
P6
H1
H2
M1
Key# Description
Replacement Parts List for Model Number P0900
Part # Qty.
1
4
4
2
1
1
4
20
1
Part H2
Qty. 20
HARDWARE IDENTIFIER:
P5
P4
P6
H1
H2
P3
P2
P1
Part H1
Qty. 4
4
PLEASE LOOK AT YOUR TABLE AND DETERMINE THE POSITIONING OF YOUR BEAMS.
INSTALLATION WILL DEPEND ON THE TYPE OF BEAM SUPPORTS YOU HAVE ON YOUR
POOL TABLE. IF THE BEAMS RUN THE WIDTH OF THE TABLE SEE PICTURE A. IF THE
BEAMS RUN THE LENGTH OF YOUR TABLE SEE PICTURE B.
B
IF THE BEAMS RUN THE LENGTH OF
THE TABLE LIKE IN PICTURE B SKIP TO
PAGE 16 AND FOLLOW THOSE
DIRECTIONS TO INSTALL YOUR
ACCESSORY DRAWER.
A
IF BEAMS RUN THE WIDTH OF THE TABLE LIKE
IN PICTURE A GO TO THE NEXT PAGE AND
FOLLOW THOSE DIRECTIONS.
5
OVERVIEW OF INSTALLATION PROCEDURE:
BOTTOM EDGE
FRONT OF
DRAWER
4”
20”
location of the first
row of mounting holes
location of the Second
row of mounting holes
BEAM
SUPPORT
DETERMINE IF YOU WANT YOUR
DRAWER TO BE FLUSH TO
THE SIDE APRON OR
RECESSED.
SIDE VIEW
OF TABLE
BOTTOM VIEW
OF TABLE
Beam Support
on your table
Beam Support
on your table
THE FRONT OF DRAWER
WILL GO ON THIS SIDE
OF THE TABLE
Please look at the pictures below and familiarize yourself with your pool table
and which side of the table you want to attach your accessory drawer to. When
fully assembled the Drawer should be flush to the bottom edge of the Side
Apron of your table (unless you want the Drawer recessed), this is why its
important to measure accurately before pre-drilling your holes. Continue to the
next page to start assembly, you will need a cordless drill, a 7/64” drill bit a
tape measure and a fine tip marker such as a Sharpie.
NOTE:
OF SIDE APRON
6
BOTTOM VIEW
OF TABLE
OF SIDE APRON
BEAM
SUPPORTS
16”
1. Determine which side of your pool table you want to attach your Accessory Drawer
and how far in (recessed) from the bottom edge of Side Apron.
1
Figure
2. Measure 4” from the outside of the front face of the Drawer to the center of the
Beams on your table. Mark the location of where you will drill the pilot holes,
making sure hole marks are parallel to each other. See Figure 1.
3. Measure 20” from the outside of the Front of the Drawer (or 16” from the first set
of holes) to the center of the Beams. Mark the location of where you will drill the
pilot holes, making sure hole marks are parallel to each other. See Figure 1.
4. Double check the makings for the pilot holes before drilling. Hole markings must
be centered and square to other hole markings for proper drawer alignment.
Using a 7/64” bit, drill pilot holes about 1” deep into the Beam supports, keep
Drill straight when drilling so pilot hole is as straight as possible.
BOTTOM EDGE
FRONT OF
DRAWER
4”
20”
location of the first
row of mounting holes
location of the Second
row of mounting holes
BEAM
SUPPORT
SIDE VIEW
OF TABLE
OF SIDE APRON
FRONT OF
DRAWER
DETERMINE IF YOU WANT YOUR
DRAWER TO BE FLUSH TO
THE SIDE APRON OR
RECESSED.
NOTE:
4”
20”
BOTTOM EDGE
7
(MOUNTING RAIL)
P4
2
Figure
THREADED
STUDS
THREADED
STUDS
(MOUNTING SLOTS)
5. Become familiar with Mounting Rail P4. Different mounting
slots will be used depending on the distance between your
Beam supports. You will attach screws H1 through the
mounting slots and into the pre-drilled holes you made in the
previous step. The threaded studs will be facing toward the
back when attached to the pool table Beams in the next step.
See Figure 2.
(MOUNTING SLOTS)
Note: H1 Screws will attach
from the bottom in the
next step.
6. You will need two P4 Rails and four H1 Screws for the next
step.
8
Threaded studs on P4 Rail
must be facing toward the
back as shown.
SIDE VIEW
OF TABLE
3
Figure
BEAM
SUPPORTS
THE FRONT OF
DRAWER WILL
GO ON THIS SIDE
BOTTOM VIEW
OF TABLE
THE FRONT OF
DRAWER WILL
GO ON THIS SIDE
DETAIL A
Threaded studs on P4 Rail must
be facing toward the back.
Threaded studs on P4 Rail
must be facing toward the
back as shown.
Threaded studs on P4 Rail must
be facing toward the back.
P4
7. Attach Mounting Rails P4, to the support Beams with four H1 screws. Attach
screws H1 through the mounting slots and into the pre-drilled holes you made,
check to make sure Mounting Rails square, straight and centered on beams
before tightening, DO NOT over-tighten screws. The threaded studs should
be facing toward the back. See Figure 3, Detail A & Side View.
BEAM
SUPPORTS
CAUTION:
DO NOT OVER TIGHTEN SCREWS! BECAUSE YOU COULD STRIP SCREWS
IN THE WOOD BEAMS DOING IRREPARABLE DAMAGE TO THE TABLE.
H1
H1
9
TOP VIEW
NOTE: MAKE SURE
THIS EDGE IS
FACING UP
4
Figure
PARTS NEEDED:
1 - (P5) Mounting Frame
8. Fold Mounting Frame P5 so that the noted threaded studs face out as
shown in Figure 4 & the Top View.
P5
Threaded
studs
Threaded
studs
Threaded
studs
Threaded
studs
Threaded
studs
Threaded
studs
Threaded
studs
Threaded
studs
P5
10
NOTE: P3 Connector
can extend on slider
along the slot on P2.
5
Figure
P2
P3
H2
DETAIL B
P3
P2
P3
P2
9. Attach P2 hanger to P3 Connector with H2 Hex nut as shown in Figure 5. Leave nut
H2 loose enough for P3 to slide freely on P2. See Detail B. Repeat step for the
remaining P2 & P3 parts.
PARTS NEEDED:
4 - (P2) Hanger
4 - (P3) Connector
4 - (H2) Hex Nut
Stud
Threaded
Indice
Altri manuali ESCALADE Gioco
ESCALADE
ESCALADE Triumph 35-7052-2 Manuale utente
ESCALADE
ESCALADE Atomic G01342W Manuale utente
ESCALADE
ESCALADE ping-pong T8466F Manuale utente
ESCALADE
ESCALADE Triumph Manuale utente
ESCALADE
ESCALADE Triumph 45-6747 Manuale utente
ESCALADE
ESCALADE Viva Sol Manuale utente
ESCALADE
ESCALADE G07611 Manuale utente
ESCALADE
ESCALADE Triumph 35-7077 Manuale utente
ESCALADE
ESCALADE Triumph Hyperloop Manuale utente
ESCALADE
ESCALADE Atomic G01344W Manuale utente
Manuali Gioco popolari di altre marche
Koala Technologies
Koala Technologies KoalaWare Spider Eater Manuale utente
Tomy
Tomy The Magic Oven Manuale utente
Sega
Sega GAME SHOW Manuale utente
Tiger Electronics
Tiger Electronics Last Out 7-584-0 Manuale utente
Fisher-Price
Fisher-Price RollOverRover Manuale utente
Mattel
Mattel World Championship Football Manuale utente