Eskon EPA 200 Manuale utente

KK-EPA.004 Rev No:0 28.09.18

EPA 200

USER

MANUAL

PROCESS CONTROL DEVICE

KK-EPA.004 Rev No:0 28.09.18

INDEX

INDEX ................................................................................................................................................................................2

1.TECHNICAL SPECIFICATIONS ..........................................................................................................................................4

2. MECHANICAL DIMENSIONS ..........................................................................................................................................4

3. CONNECTIONS...............................................................................................................................................................5

4. FRONT PANEL IDENTIFICATIONS...................................................................................................................................6

5. MENU TREE...................................................................................................................................................................7

6. SETUP ............................................................................................................................................................................8

6.1 Connecting the Sensor to the Device......................................................................................................................8

6.2.1. Setting the Scale Value..................................................................................................................................9

6.2.2 Setting Factor Value.........................................................................................................................................9

6.2.3 Setting Calibration Method............................................................................................................................10

6.2.4 Start Calibration (START)................................................................................................................................11

6.3. ADJUSTING THE RELAY SET VALUES.....................................................................................................................11

6.3.1. Relay Output Settings ...................................................................................................................................11

6.3.2 Changing Quick Set Values.............................................................................................................................12

6.4. RELAY PROGRAMMING MODE ............................................................................................................................12

6.4.1. Relay Function Selection...............................................................................................................................12

6.4.2 Delay ..............................................................................................................................................................14

6.4.3. Hysteresis......................................................................................................................................................14

6.4.4. Offset Value...................................................................................................................................................15

6.4.5. Default Status Of The Relay (Cond)...............................................................................................................15

6.4.6. Sensor Selection (Snsor)................................................................................................................................16

6.5. ANALOGUE OUTPUT SETTINGS............................................................................................................................16

6.5.1. Analogue Output Type Selection ..................................................................................................................16

6.5.2. Analogue Output ON/OFF.............................................................................................................................17

6.5.3. Inverse Setting ..............................................................................................................................................17

6.5.4. Analogue Output Scale Setting .....................................................................................................................18

6.5.5. Wave Function ..............................................................................................................................................18

6.6. DIGITAL OUTPUT SETTINGS..................................................................................................................................19

6.6.1. UART Settings................................................................................................................................................19

6.6.2. CAN-Open Settings........................................................................................................................................21

6.7. KEY TONE (SOUND) SETTING................................................................................................................................25

6.8. SECURITY (SECURE) MENU...................................................................................................................................25

6.8.1. Hide the Menu (HIDE)...................................................................................................................................25

6.8.2. Lock the Menu (LOCK)...................................................................................................................................26

KK-EPA.004 Rev No:0 28.09.18

6.8.3. Password Determination (PASS)...................................................................................................................26

6.8.4. Return to Factory Settings (FTRY) .................................................................................................................26

6.8.5. Restart the Device (RESET)............................................................................................................................27

7. OTHER SETTINGS.........................................................................................................................................................27

7.1. Display Menu .......................................................................................................................................................27

7.1.1. Decimal Point (POINT)...................................................................................................................................27

7.1.2. Tare Function (TARE).....................................................................................................................................28

7.1.2.1. Event ..........................................................................................................................................................28

7.1.2.2. Input...........................................................................................................................................................28

7.1.3. Screen Refresh Rate (REFRS).........................................................................................................................29

7.1.4. Prevention for Screen Flicker (FILTR)...........................................................................................................30

7.1.4.1. AVRGE (Average Calculation):....................................................................................................................30

8. OPERATION MODE FUNCTIONS..................................................................................................................................34

8.1. Tare (Reset ) Fonction......................................................................................................................................34

8.2. Viewing Maximum and Minimum Values which are read...............................................................................34

9. PRODUCT CODING ......................................................................................................................................................35

10. WARRANTY CERTIFICATE ..........................................................................................................................................36

KK-EPA.004 Rev No:0 28.09.18

1.TECHNICAL SPECIFICATIONS

2. MECHANICAL DIMENSIONS

Supply Voltage

24 VAC/DC 50/60 Hz

85-265 VAC 50/60 Hz

Power Consumption

9 VA / 2,7 Watt Maximum

Sensor Supply Voltage

Pot:

5 VDC

mV/V:

10 VDC

0-10V:

24 VDC

0-5V:

5 VDC

0,5-4,5V:

5 VDC

4-20 mA:

24 VDC

CANopen:

24 VDC

Max Sensor Supply Current

100 mA

Sampling Rate

3.5 kHz

Input Resolution

16 bit

Thermocouple Resolution

19 bit

RTD Resolution

15 bit

Analogue Inputs

Potentiometer, 0-10 V, 4-20 mA, 0-20 mA, 3,33 mV/V, 2mV/V, 2,5mV/V Ratiometric,

Thermocouple (K, J, N, R, S, T, E and B type), RTD

Relay Outputs

3 pcs 250 VAC 3A (For Resistive Load) Relay

Serial Communication (Optional)

RS-232, RS-485, USB, CANopen

Analogue Outputs (Optional)

0-10 V, 0-5 V, 0.5- 4.5 V, 4-20 mA, 0-20 mA

Analogue Output Resolution

12 bit

Connection

Terminals with 2,5 mm2sockets

Operating Temperature

0 °C … 50 °C

Storage Temperature

-10 °C … 60 °C

Protection Class

IP60 Front Panel, IP20 Back Panel

Dimensions

67 x 67 x 74 mm

Weight

~190 gr

Mounting

It is fixed to the panel with the feet at the top and bottom.

SECTION A-A

KK-EPA.004 Rev No:0 28.09.18

1. Relay Output

OUT-1

2. Relay Output

OUT-2

3. Relay Output

OUT-3

Supply Voltage

24 VAC/DC or

85/265 VAC

The following table

shows the pin

numbers.

Digital

Communication

Analogue Outputs

and Tare Input

Sensor Inputs

3. CONNECTIONS

Digital Conn.

RS485

GND

RS232

GND

USB HID

USB B TYPE CONNECTOR

USB VIRTUAL

USB B TYPE CONNECTOR

CANopen

CAN HIGH

CAN LOW

GND

Analogue

Outputs

4-20 mA

Output

GND

4-20 mA

Output

0-10 V

Output

GND

0-10 V

Output

Tare Input

Tare

Input

GND

SENSOR

Potentiometer

3. terminal

2. terminal

1. terminal

4-20 mA Input

GND

Sensor Signal

Sensor Supply

0-20 mA Input

GND

Sensor Signal

Sensor Supply

0-10 V Input

GND

Sensor Signal

Sensor Supply

3,33 mV/V Input

2 mV/V Input

2.5 mV/V Input

GND

Sensor Supply

Signal(-)

Signal(+)

Thermocouple

T-

T+

RTD

R-

R+

KK-EPA.004 Rev No:0 28.09.18

4. FRONT PANEL IDENTIFICATIONS

SAFETY WARNINGS

1. Always follow the instructions and instructions in the operating instructions before making

the connections and during use.

2. Please check the power supply type before you connect energy to your device.

3. During the operation, be sure to mount it firmly on the panel to be used against falling,

sliding, shaking and shaking.

4. Make sure the sensor connections are not energized in your device, and do not disconnect or

connect the devices while the device is running.

5. Make sure that the cables between the sensor and your device are shielded and free from

high-current energy cables.

6. Do not expose your device directly to a heat source (solar, heater, etc.) in its operating

environment.

7. The EPA200 is an industrial control device which is not suitable for outdoor use; please use

only in room conditions.

8. Wipe with a damp cloth to clean your device, do not use water, alcohol, thinner and

similiar chemicals.

9. Comply with the limit values specified in the technical specifications for relay outputs.

10. The device cannot be changed by the user in the event of a fault, Please contact our

technical service in case of failure.

1) Top Display Line: It has 5 digits and shows the

measured process value.

2) Bottom Display Line: It has 6 digits and shows the relay

setpoint, the temperature measured by the thermocouple

or the ambient temperature.

3)Min Status LED: It lights up when the lowest

(minimum) value has been read since the moment the

device is started.

4) Max Status LED: It lights up when the maximum value

has been read since the moment the device is started.

5) Tare Status LED: It lights up when the Tare function is

active.

6) Set Status LEDs: The LED associated with the active relay lights up.

7) PRG Button: Programming and Enter key. It is used to enter menus or to confirm entered values.

8) ESC Button: Escape, exit and back key. It is used to return to the upper menu or to exit the menu.

9)UP and DOWN Buttons: Navigating through the menus; is used to increase and decrease the value while entering

values, or to move to a lower and higher digit.

KK-EPA.004 Rev No:0 28.09.18

5. MENU TREE

Top Menu

Sub Menu

Out - 3

SCALE

LABEL

UNIT

POINT

TARE

REFRS

Out - 2

KK-EPA.004 Rev No:0 28.09.18

6. SETUP

6.1 Connecting the Sensor to the Device

Potentiometer Connection

4…20mA / 0…20mA Connection

*2 wire connection:

Sensor supply terminal must be connected to terminal 22

Sensor signal terminal must be connected to terminal 23

mV/Volt Connection

0…10 Volt Connection

Thermocouple Connection

RTD Connection

Potentiometer Connection

*0-5 V and 0.5-4.5 V connections are made as above.

*K, J, N, R, S, T, E and B type thermocouples can be connected

KK-EPA.004 Rev No:0 28.09.18

6.2 Device Calibration

Press and hold to the PRG key to switch to the programming menu.

6.2.1. Setting the Scale Value

Your device is automatically calibrated to the factory settings and operates in the 0-100 range. That is, the

smallest value read on the sensor is 0, and the maximum value is 100 on the display. You can change this

scale on calibration menu. Use the S-LO for the minimum value displayed on the screen and the S-HI option

for the maximum value.

* After you have set the S-LO value, you can do the same for the S-HI value.

6.2.2 Setting Factor Value

You can use the Fctor menu to expand your scale by multiplying it with a fixed factor.The number of this

factor, which is the default value of 1, is multiplied by the values of S-LO and S-HI to determine the scale

value.

For example; When you set the S-LO value to 1, the S-HI value to 20 and make the factor 4, your device will

operate in the range of 4-80 value range.

WARNING: Changing the scale and factor value does not change the calibration of your device, it only

indicates the displayed value range on the screen.

25.

2.5

The decimal point

starts flashing. Use

the UP and DOWN

buttons to select the

decimal digits point.

Press and hold the UP button to

move to the next step. To enter a

negative (-) value, move to one of

the non-digit digits and press the

DOWN button.

When you press and hold

to the PRG key, the value

in the second line starts

blinking. Enter the

desired value using the

UP and DOWN buttons.

2.5

The new S-LO value you confirmed with the PRG key has been

set. Press UP button to move to S-HI.

OUT

S-LO.

Cal

SCALE

Press and hold the PRG button.

KK-EPA.004 Rev No:0 28.09.18

6.2.3 Setting Calibration Method

Your device has been calibrated during production. If you want, you can do this calibration according to

your sensor. To do that you should select the calibration method on this menu.

6.2.3.1 Factory calibration (default)

The default calibration on your device. The multipoint calibration or the two pointed calibration that you

have made to your device does not disturb the factory calibration.

6.2.3.2 Two-point calibration

By two-point calibration option, only the maximum and minimum points are selected. For example; While

you are calibrating a 10 cm linear potentiometer, the minimum point is identified when the potentiometer

is in the fully closed position and the maximum point is identified when the potentiometer is in the fully

open position.

* After you set the CAL-L value, you can do the same for the CAL-H value.

6.2.3.3 Multiple (segmented) Calibration

With the multiple calibration option, you can calibrate your device at up to 10 different points. This

method increases the linearity of the sensor.

For example; If the length of the sensor is 40 cm and you want to calibrate at 5 different points, these

points are; There may be 0. cm, 10. cm, 20 cm, 30 cm when sensor starts and 40 cm points where the

sensor ends. These points can be set anywhere in the scale range. We recommend you to choose by equal

intervals for a more suitable linearity.

6.2.3.4. Determining the Number of Calibrations (CL.CNT)

If you select the multi-segmented calibration option, in this menu that appears, you can specify the

number of points you want to calibrate the device. It's a maximum of 10.

FCAL

2_Pnt.

SEGnt.

Factory calibration (Default)

CL.Cnt.

When the PRG button is pressed and entered into the menu, the second line starts blinking. Enter the desired value using

the UP and DOWN buttons and confirm by pressing the PRG button again.

START

CAL-L

XXX

.donE.

Multiple (Segmented )

Calibration

2 pointed calibration

CL.Cnt.

Indice

Altri manuali Eskon Controllori

Eskon

Eskon EPA300 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente