ESP EZ-LOCK Manuale utente
USER MANUAL
EZ-LOCK Manual_La out 5 04/04/2013 14:53 Page 1
2
Equipment required for controlling one door:-
12 volt DC power supply 2 amp minimum (EV-BPS)
Lock - Magnetic (EVML-250)/Yale type keep 12 volt lock (enter D)
Push to exit button (EVEXIT)
Green break glass emergency release (EVEBG)*
*Note:- for use with Magnetic lock only
Functions of the EZ-LOCK
The EZ-LOC can control up to two doors by use of pin numbers.
Selectable Pin number length 2,3,4,5 and 6 digits (per zone).
Programmable door open time 00 to 99 seconds.
Two locations (zone 1, zone 2) are available for programming pin
numbers.
1000 Pins can be programmed for zone 1.
10 Pins can be programmed for zone 2.
Two volt free change over relays one per door.
Door closed function (contact required).
2 push to exit button inputs, one per zone.
Programmable volt free change over relay for door bell function.
Programmable rear tamper.
Internal buzzer for tamper monitoring (auto cut off after 1 min).
1 x Security Torx ey
4 x Screws and raw plugs
Manual and
Marking out template
EZ-LOC
and Back Plate
Contents
EZ-LOCK Manual_La out 5 04/04/2013 14:53 Page 2
3
Sighting Of The EZ-LOCK
Site the EZ-LOC within easy access to the door/doors to be controlled.
Recommended mounting height 1.2m.
Fitting
Using the template mark and drill the fixing and cable entry holes.
Remove security screw from the underside of the keypad and
remove back plate.
Fit and secure the back plate in its final position. (See Fig. 1)
Feed the cable from the keypad though the centre hole of the
back plate.
Clip the top of keypad onto the back plate and secure using the
security fixing screw located on the underside of the keypad.
Make all wiring connections and connect 12 volts DC to the keypad.
The green power LED will now be illuminated on the front of the keypad.
System wiring
Screw
raw
plugs
Screws
Torx Screw
Fig. 1
EZ-LOCK Manual_La out 5 04/04/2013 14:53 Page 3
4
Yellow-push to exit button - Zone 2
Additional power
supply for lock
Brown-door status detecting - reed switch
Orange-push to exit button - Zone 1
Green - COM
Not Used
Not Used
Exit button - Zone 2
Exit button - Zone 1
COM
Door contact - reed switc
h
Wiring Diagram and connections
EZ-LOCK Manual_La out 5 04/04/2013 14:53 Page 4
5
RED
BLACK
WHITE
PINK
Exit Button
0-20
L N
E.lock
+ -
DC out
+ -
Push button
GND P.B
N.O
Timer
secs
240vAC
INPUT
EV-BPS
Yale Release
Exit Button
0-20
L N
E.lock
+ -
DC out
+ -
Push button
GND P.B
N.C
Timer
secs
RED
BLACK
WHITE
PINK
INPUT
EV-BPS
Maglock
Emergency
door release
COM
N.C
Capacitor
0.47uF
100v
240vAC
Wiring Diagram for Maglock
Wiring Diagram for ale Release
EZ-LOCK Manual_La out 5 04/04/2013 14:53 Page 5
Brief details of programming
Access To programming mode.
Programme pin numbers.
There are two locations for entering pin numbers (zone 1 and zone 2).
Zone 1 has 1000 locations available 000-999.
Zone 2 has 10 locations available 00-09.
Select the lock release times (00-99 seconds) zone 1 and zone 2.
How to escape programming mode.
Note:- if no keys are pressed for 30 seconds the unit will drop out of
programming mode automatically.
How to enter and exit programme mode
• To enter programme mode enter the 4 digit pin number twice
(default pin 1234).
• To exit programme mode press the # key.
Zone 1 programming
Programming a User Pin number to Zone 1
Note:- Zone 1 has 1000 locations available from 000 to 999.
1. Enter programming mode
A Long bleep will be heard and the green power LED will turn orange.
2. Enter the vacant location you want to programme the pin
number in use a 3 digit format (xxx).
The green programming LED (top left of keypad) will illuminate.
Note:- if this location already has a pin number programmed the LED will
turn red.
To delete this location press the star *key twice. The LED will now turn
green.
3. Enter the pin number required, a conformation bleep will be
heard.
If further pin numbers are to be programmed select the next available
location number (xxx).
6
EZ-LOCK Manual_La out 5 04/04/2013 14:53 Page 6
7
Setting the Unlock Time for Zone 1
1. Enter programming mode.
A Long bleep will be heard and the green power LED will turn orange.
2. Press the *key then the 1 key the orange LED will start to
flash
3. Enter the time in seconds for the unlock time from 00 to 99
seconds.
Zone 2 programming
Programming A User Pin number to Zone 2
Note:- Zone 2 has 10 locations available 00-09.
1. Enter programming mode
A Long bleep will be heard and the green power LED will turn orange.
2. Press the *key followed by the 4 key
The orange LED will start to flash
3. Enter the vacant location number you want to programme the
pin number in to (xx).
The green programming LED (top left of keypad) will illuminate.
Note:- if this location already has a pin number the LED will turn red.
To delete this location press the star *key twice. The LED will now turn
green.
4. Enter the new pin number required, a conformation bleep will
be heard.
If further pin numbers are to be programmed select the next available
location number (xx).
Setting the Unlock Time for Zone 2
1. Enter programming mode.
A Long bleep will be heard and the green power LED will turn orange.
2. Press the *key then the 5 key the power LED will start to
flash.
3. Enter the time in seconds for the unlock time from 00 to 99
seconds.
EZ-LOCK Manual_La out 5 04/04/2013 14:53 Page 7
8
How to Change the Programming Pin Number
1. Enter programming mode.
A Long bleep will be heard and the green power LED will turn orange.
2. Press *key followed by the 3 key the orange LED will start to
flash.
3. Enter the new programming pin twice.
A conformation bleep will be heard.
How to delete all pin numbers
1. Enter programming mode.
A Long bleep will be heard and the green power LED will turn orange.
2. Press *key followed by the 8 key the orange LED will start to
flash.
3. Press the 8 key twice.
7 conformation bleeps will sound.
Deleting a Pin number from Zone1
1. Enter programming mode
A Long bleep will be heard and the green power LED will turn orange.
2. Enter the location number of the pin number/tag you wish to delete
using a 3 digit format (xxx).
The red LED will illuminate.
3. Press the star * key twice.
The LED will now turn green.
Deleting a Pin number from Zone2
1. Enter programming mode
A Long bleep will be heard and the green power LED will turn orange.
2. Press the * key followed by the 4 key
The orange LED will start to flash
3. Enter the location number of the pin number/tag you wish to delete
using a 2 digit format (xx).
The red LED will illuminate.
4. Press the star *key twice.
The LED will now turn green.
EZ-LOCK Manual_La out 5 04/04/2013 14:53 Page 8
9
How to load factory default settings
1. Enter programming mode.
A Long bleep will be heard and the green power LED will turn orange.
2. Press the *key followed by the 8 key the orange LED will start
to flash.
3. Press the 9 key twice.
One bleep will sound and the System will automatically come out of
programming mode.
How to Disable the rear tamper
1. Enter programming mode.
A Long bleep will be heard and the green power LED will turn orange.
2. Press the *key followed by the 6 key the orange LED will start
to flash.
3. Press the 0 key followed by the 1 key.
The rear tamer is now off.
How to Enable the rear tamper
1. Enter programming mode.
A Long bleep will be heard and the green power LED will turn orange.
2. Press the *key followed by the 6 key the orange LED will start
to flash.
3. Press the 0 key followed by the 2 key.
The rear tamer is now on.
EZ-LOCK Manual_La out 5 04/04/2013 14:53 Page 9
How to set the length of the pin numbers to be used
1. Enter programming mode by entering the 4 digit pin number
twice (default pin 1234).
A Long bleep will be heard and the green power LED will turn orange.
2. Press the *key followed by the 9 key the orange LED will now
flash.
3. Press 04 a long bleep will be heard.
4. Enter the length of the pin number you require (2,3,4,5 or 6).
If the length is the same as already programmed you will get a
conformation bleep.
If you have changed the length you will get 7 bleeps to say it has now
been changed.
Note:- Any pin numbers programmed into the system will be deleted if the
pin length is change.
How to Enable the door Bell function
Note:- If two doors are being controlled the bell function can not be used.
1. Enter programming mode.
A Long bleep will be heard and the green power LED will turn orange.
2. Press the *key followed by the 2 key the orange LED will start
to flash.
3. Press the 0 key followed by the 2 key.
The door bell function is now on.
Note:- The * key is now used to ring the doorbell
How to Disable the door Bell function
1. Enter programming mode.
A Long bleep will be heard and the green power LED will turn orange.
2. Press the *key followed by the 2 key the orange LED will start
to flash.
3. Press the 0 key followed by the 1 key.
The door bell function is now off.
10
EZ-LOCK Manual_La out 5 04/04/2013 14:53 Page 10
Indice
Altri manuali ESP Tastiera
