EST EST3X Manuale del prodotto

EST3X Technical

Reference Manual

P/N 3101888-EN • REV 03 • ISS 28AUG13

Australia/New Zealand technicians please note

Certain functions and features contained in this manual are

not suitable for the ANZ market. Please refer to ANZ specific

material regarding Australian display.

2013 UTC Fire & Security Americas Corporation, Inc.

This document may not be copied in whole or in part or otherwise

reproduced without prior written consent from

UTC Fire & Security

Americas Corporation, Inc.

, except where specifically permitted

under US and international copyright law

Trademarks and

patents

The

EST3X name and logo are trademarks of UTC Fire & Security

Americas Corporation, Inc.

Other trade names used in this d

ocument may be trademarks or

registered trademarks of the manufacturers or vendors of the

respective products

Manufacturer

Edwards, A Division of

UTC Fire & Security Americas Corporation, Inc.

8985 Town Center Parkway, Bradento

n, FL 34202, USA

Version

This document applies to

EST3X with C-CPU firmware version 1.x.

Contact information

For contact information

,see www.est-fire.com.

EST3X Technical Reference Manual i

Content

Important information iv

Chapter 1 Introduction 1

About this manual 2

Intended audience 2

Fire alarm system limitations 3

Chapter 2 Product description 5

General description 6

Panel components 10

Minimum system requirements 15

EST3X user interface 15

Event message queues 20

User access levels 22

Command menus 23

Chapter 3 Operating instructions 37

Operating states 39

Control panel power up 43

Using the rotary controller 44

Accessing the Queue Menu 46

Accessing the Main Menu 46

Silencing the panel buzzer 47

Silencing alarm signals 47

Acknowledging events 48

Resetting the fire alarm system 49

Restarting the fire alarm system 49

Clearing the alarm history 50

Viewing event message details 50

Viewing reports 51

Disabling and enabling devices 56

Disabling and enabling option cards 57

Disabling and enabling logic groups 58

Disabling and enabling system time controls 59

Activating alarm signals manually 60

Testing the system and devices 60

Changing output states 62

Switching the smoke detector alarm sensitivity threshold 64

Changing event message routing 65

ii EST3X Technical Reference Manual

Changing Access Level passwords 66

Changing the LCD screen language 67

Downloading a database 67

Using a TCP/IP connection to read from the panel 70

Setting the system time and date 71

Configuring holiday lists 72

Control-display modules 72

Guard patrols 76

Chapter 4 Supplementary applications 79

Digital audio subsystem 80

Remote annunciation 89

Integrated EST3 network 94

Building management system communication 96

FireWorks communication 97

Chapter 5 Installation 99

UL 864 notification appliance circuit (NAC) signal

synchronization 101

Creating an initial startup database 110

System installation sequence 111

Component installation 112

Preliminary field wiring testing 128

3-MODCOM Modem Communicator module 130

Connecting a PT-1S serial printer 136

Connecting a CDR-3 for coded tone output 140

R-Series annunciator DIP switch settings 145

Runtime errors 146

Chapter 6 Preventive maintenance and testing 149

Visual inspections 150

Routine maintenance and tests 151

System trouble and maintenance log 165

Record of completion 166

Chapter 7 Service and troubleshooting 167

System repairs 169

Precautions 170

Panel restart problems 170

Hardware problems 171

Hardware troubleshooting 172

Pseudo points 185

Understanding Signature data loops 198

Signature loop controller troubleshooting 210

EST3X Technical Reference Manual iii

Signature device troubleshooting 212

Using the SDU Signature Series diagnostics tools213

Analog addressable devices and modules 222

Analog device troubleshooting 224

Using the SDU Analog Addressable diagnostic tools 226

Using HyperTerminal to troubleshoot the system 229

Appendix A System calculations 231

Network data riser limits 232

Signature data loop wire length 234

Notification appliance signaling line circuit calculations 242

25 or 70 VRMS NAC wire length 248

Analog addressable circuit wire length 250

Cabinet battery 250

Fiber optic cable worksheet 255

Appendix B Addresses 257

Address formats 258

Card address 258

Hardware layer device addresses 260

Operator layer device address 261

Remote annunciator device addresses 263

Logic group addresses 271

Appendix C Programming options 273

Programming options 274

Glossary 277

Index 281

iv EST3X Technical Reference Manual

Important information

Regulatory information

This product has been designed to meet the requirements of NFPA 72 National

Fire Alarm Code, UL 864 Standard for Control Units for Fire Protective Signaling

Systems, and ULC S527 Standard for Control Units for Fire Alarm Systems.

Limitation of liability

To the maximum extent permitted by applicable law, in no event will UTCFS be

liable for any lost profits or business opportunities, loss of use, business

interruption, loss of data, or any other indirect, special, incidental, or

consequential damages under any theory of liability, whether based in contract,

tort, negligence, product liability, or otherwise. Because some jurisdictions do not

allow the exclusion or limitation of liability for consequential or incidental

damages the preceding limitation may not apply to you. In any event the total

liability of UTCFS shall not exceed the purchase price of the product. The

foregoing limitation will apply to the maximum extent permitted by applicable law,

regardless of whether UTCFS has been advised of the possibility of such

damages and regardless of whether any remedy fails of its essential purpose.

Installation in accordance with this manual, applicable codes, and the instructions

of the authority having jurisdiction is mandatory.

While every precaution has been taken during the preparation of this manual to

ensure the accuracy of its contents, UTCFS assumes no responsibility for errors

or omissions.

Advisory messages

Advisory messages alert you to conditions or practices that can cause unwanted

results. The advisory messages used in this document are shown and described

below.

WARNING: Warning messages advise you of hazards that could result in injury

or loss of life. They tell you which actions to take or to avoid in order to prevent

the injury or loss of life.

Caution: Caution messages advise you of possible equipment damage. They tell

you which actions to take or to avoid in order to prevent the damage.

EST3X Technical Reference Manual v

Note: Note messages advise you of the possible loss of time or effort. They

describe how to avoid the loss. Notes are also used to point out important

information that you should read.

EST3X FCC compliance

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his own expense.

3-MODCOM FCC compliance

Cautions

•To ensure proper operation, this dialer must be installed according to the

enclosed installation instructions. To verify that the dialer is operating properly

and can successfully report an alarm, it must be tested immediately after

installation, and periodically thereafter, according to the enclosed test

instructions.

•In order for the dialer to be able to seize the phone line to report an alarm or

other event when other customer equipment (telephone, answering system,

computer modem, etc.) connected to the same line is in use, the dialer must

be connected to a properly installed RJ-31X jack. The RJ-31X jack must be

connected in series with, and ahead of, all other equipment attached to the

same phone line. Series installation of an RJ-31X jack is depicted in the

wiring diagram. If you have any questions concerning these instructions, you

should consult your telephone company or a qualified installer.

Testing

When programming emergency numbers or making test calls to emergency

numbers, remain on the line and briefly explain to the dispatcher the reason for

the call. Perform programming and testing activities in the off-peak hours, such

as early morning or late evenings.

vi EST3X Technical Reference Manual

Compliance

•For equipment approved before July 23, 2001: This dialer complies with

Part 68 of the FCC rules. A label attached to the dialer contains, among other

information, the FCC registration number and ringer equivalence number

(REN) for this equipment. If requested, this information must be provided to

the telephone company.

•For equipment approved after July 23, 2001: This dialer complies with Part

68 of the FCC rules and the requirements adopted by the Administrative

Council for Terminal Attachments (ACTA). A label attached to the dialer

contains, among other information, a product identifier in the format

US:AAAEQ##TXXXX. If requested, this information must be provided to the

telephone company.

•The plug and jack used to connect the dialer to the premises wiring and

telephone network must comply with the applicable FCC Part 68 rules and

requirements adopted by ACTA. The dialer must be connected to a compliant

RJ-31X or RJ-38X jack using a compliant cord. If a modular telephone cord is

supplied with the dialer, it is designed to meet these requirements. See

installation instructions for details.

•A ringer equivalence number is used to determine how many devices you can

connect to a telephone line. If the total REN value for all devices connected

on a telephone line exceeds that allowed by the telephone company, the

devices may not ring on an incoming call. In most (but not all) areas the total

REN value should not exceed 5.0. To be certain of the total REN value

allowed on a telephone line, contact the local telephone company.

For products approved after July 23, 2001, the REN is part of the product

identifier in the format US:AAAEQ##TXXXX. The digits ## represent the REN

without a decimal point. Example: 03 is an REN of 0.3. For earlier products

the REN is listed separately.

•If the dialer is harming the telephone network, the telephone company will

notify you in advance that temporary discontinuance of service may be

required. If advance notice isn’t practical, the telephone company will notify

you as soon as possible. You will also be advised of your right to file a

complaint with the FCC, if you believe it is necessary.

•The telephone company may make changes to its facilities, equipment,

operations, or procedures that could affect the operation of the dialer. If this

happens, the telephone company will provide advance notice in order for you

to make necessary modifications to maintain uninterrupted service.

EST3X Technical Reference Manual vii

•If you are experiencing problems with the dialer, contact the manufacturer for

repair or warranty information. If the dialer is harming the telephone network,

the telephone company may request that you disconnect the dialer until the

problem is resolved.

•The dialer contains no user serviceable parts. In case of defects, return the

dialer for repair.

•You may not connect the dialer to a public coin phone or a party line service

provided by the telephone company.

3-MODCOM Industry Canada information

Note: The Industry Canada label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective,

operational, and safety requirements. Industry Canada does not guarantee the

equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be

connected to the facilities of the local telecommunications company. The

equipment must also be installed using an acceptable method of connection. The

customer should be aware that compliance with the above conditions may not

prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian

maintenance facility designated by the supplier. Any repairs or alterations made

by the user to this equipment, or equipment malfunctions, may give the

telecommunications company cause to request the user disconnect the

equipment.

Caution: Users should not attempt to make connections themselves, but should

contact the appropriate electric inspection authority, or electrician, as appropriate

Users should ensure for their own protection that the electrical ground

connections of the power utility, telephone lines, and internal metallic water pipe

system, if present, are connected together. This precaution may be particularly

important in rural areas.

Note: The Load Number (LN) assigned to each terminal device denotes the

percentage of the total load to be connected to a telephone loop which is used by

the device, to prevent overloading. The termination on a loop may consist of any

combination of devices subject only to the requirements that the sum of the Load

Numbers of all the devices does not exceed 100.

viii EST3X Technical Reference Manual

Altri manuali per EST3X

Indice

Altri manuali EST Sistema di sicurezza

EST

EST SIGA-278 Istruzioni per il montaggio

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente