Estate Swing E-S 1000D Series Manuale utente
E-S 1000D Series Instruction Manual
Estate Swing Summary of Functions
The Estate Swing is only to be used for vehicular swing gates in a Class I setting.
Class I: A vehicular gate opener (or system) intended for use in a home
of one-to-four single family dwelling, or a garage or parking area associ-
ated therewith.
The Estate Swing automated system was designed and built for controlling vehicle
access. Do not use for any other purpose.
The external automation with an electromechanical non-reversing linear arm auto-
mates residential dual swing-leaf gates with leaves of up to 12’ in length per leaf. It
consists of an irreversible electromechanical operator with built in opening and clos-
ing limits and utilizes a worm screw system. The irreversible system ensures the gate is
mechanical locked when the motor is not operating. A lock still needs to be installed
if security or high winds are a concern. Removal of the gate slide pin will manually al-
low the gate to be opened.
For Your Assistance
Keep this manual safely stored after installation
Serial Number ________________________________
Date of Purchase _____________________________
Place of Purchase ____________________________
Have this information on hand while handling all service and warranty
issues.
E-S 1000D Series Instruction Manual
Table of Contents
The table of contents are listed to assist you locating a desired section. We do however
strongly suggest studying every page of the instruction manual before attempting installation.
Section 1: Review of Specifications, Warnings, and Tools
Specifications of the Estate Swing and Components 1.1
Parts List 1.2
System Overview & Preliminary Checks 1.3
Tools Needed for Installation 1.4
Section 2: Installation of Mounting Brackets
Manual Operation 2.1
Pull to Open Illustration 2.2
IMPORTANT: Determining Setback—Pull to Open 2.3
Installation of Operator—Pull to Open 2.4-7
Push to Open Illustration 2.8
IMPORTANT: Determining Setback—Push to Open 2.9
Installation of Operator—Push to Open 2.10-13
Section 3: Gate Operator Mounting, Wiring Motors and Power
Mounting Gate Operator(s) & Finding Limits 3.1-.2
Control Box & Running Wires 3.3
Easy Wiring Under Driveway 3.4
Removing Terminal Strips for Wiring 3.5
Wiring the Operator Arms(s) (Pull & Push to Open) 3.6-7
Temporary Safety Jumpers & Dip Switch Settings 3.8
Power 3.9
Section 4: Start Up and Operation
First Run 4.1
Determine Run Time 4.2
Operating Parameters Customization 4.3
433 Plug-In Receiver 4.4-.5
Section 5: Maintenance, Troubleshooting, and Accessories
Maintenance 5.1
Troubleshooting 5.2-.5
Control Board Overview 5.6-.10
Accessories 6.0-.1
E-S 1000D Series Instruction Manual
Section 1:
Review of Specifications, Warnings,
and Tools
E-S 1000D Series Instruction Manual
Specifications
Model Estate Swing E-S 1000D
Power Supply Group Size 24 Deep Cycle Marine
Battery (not included)
Current (A) 3
Travel (in.) 12
Cycles per hour 50% Duty Cycle / Approx.. 35
Operating Ambient Temp 0 to 100 F
Protection Class IP44
Gate leaf max length (ft.) Up to 12
Gate leaf max weight (lbs.) Up to 600
Operator Type Screw Drive
Operator Weight 14 lbs.
Gate Weight / Length Ratio 6’ 8’ 10’ 12’
100 lbs X X X X
200 lbs X X X X
300 lbs X X X X
400 lbs X X X
500 lbs X X
600 lbs X
The above chart represents the maximum weight and length combinations that this gate
opener can handle. The lengths and weights are either for a single gate or for a single leaf
of a dual gate.
1.1
E-S 1000D Series Instruction Manual
Estate Swing Parts List
1.2
A. Control Box with Control Board and
Receiver
B. 2 Operator Arms with 42” of Wire
C. Connector Pins and Clips
D. Wire Harness
E. 2 Gate Mounting Brackets
F. 2 Post Mounting Bracket Kits
Not Shown:
•Transmitter/Receiver Pack
•Additional Wire
•Mounting Hardware
2 - 3/8”x1 3/8” Hex bolts, washer, nut
2 - 5/16”x 1 3/8” Hex bolt, washer, nut
4 - 3/8”x 2” Carriage bolt, washers, nut
2 - 1/4” x 2” Hex bolt, washers, nut
Not Included: Battery
E-S 1000D Series Instruction Manual
Standard System Overview and Safety Zones
1.3
The system displayed below is a recommended standard system. Other approved accessories
can be installed. Photo sensors and a flashing light indicating gate movement is recommend-
ed for safety purposes.
1,2 Estate Swing Operator • 3 Photocells (not included) • 4 Control board • 5 N/A • 6 Push but-
ton opening device (not included) • 7 Receiver extension (not included)• 8 12Vdc flashing
lamp (not included) • 9 Positive stop (not included) • 10 Charging Control
Notes:
1) When laying electrical cables, use appropriate rigid and/or flexible tube
2) Do not run any wires in the same conduit as110 AC power that may be in the area. This will cause
danger of electrocution.
Important: Preliminary Checks
To ensure safety and an efficiently operating automated system, make sure the following conditions are
observed.
The gate and post must be suitable for being automated. Check that the structure is sufficiently
strong and rigid, and its dimensions and weights conform to those indicated on page 1.
Make sure the gates move smoothly without any irregular friction during entire travel.
Make sure the hinges are in good condition. Ball bearing hinges are necessary for gates weighing
over 200 lbs. or over 10’ in length.
Make sure the gate is plumb and level.
The gate post must be secured in the ground with concrete. This will prevent alteration of align-
ments and leveling during installation and during cycles.
E-S 1000D Series Instruction Manual
Tools Needed for Installation
1.4
• Power Drill
• Crescent Wrench
• Flat Head Screwdriver
• Hacksaw/Sawzall
• Phillips Head Screwdriver
• C-Ring Pliers
• Tape Measure
• Level
• Wire Strippers
• C-clamps
Other items may be needed prior to commencing installation. Bolded items are necessary to all appli-
cations.
• Group Size 24 Deep Cycle Marine Battery.
• Positive post, bracket or door stop. Although the Estate Swing 1000 features built in limit switches it is
highly recommended to have positive stops.
• 16 gauge, 2 conductor stranded direct burial low voltage wire will be required to run power to your
battery. Length is determined by distance between transformer or solar power supply and the control
box.
• 4 - 3/8” Carriage Bolts will be needed to connect the 2 “L” shaped brackets to the post. Length will
be determined by the size of your posts.
• A metal support bracket may be needed to achieve the appropriate desired setback. The metal
support bracket will be bolted or welded to your post to give a larger amount of space to mount the
provided mounting bracket.
• A voltage meter and digital camera may be necessary to run diagnostic checks.
• If your transformer is going to be plugged into an outdoor outlet you will need to weatherproof that
outlet and transformer. Electrical boxes or plug covers can be obtained from a local hardware store
to accommodate both the plug and transformer.
• Hardware to attach the control box to a post or fence.
• Wire strain reliefs for running wires into control box.
Protect all ongoing and outgoing wires with a surge suppressor.
Consult your local dealer for more information.
!
E-S 1000D Series Instruction Manual
Section 2:
Installation of Mounting Brackets
Altri manuali per E-S 1000D Series
1
Indice
