Estate 600A Manuale utente
ESTATE MIGHTY SPREADER
Model 600A
Owner Manual
Manufactured by:
COUNTRY MANUFACTURING, INC.
P.O. Box 104
Fredericktown, Ohio 43019
Phone: 1-800-335-1880
OWNER MANUAL AND INSTRUCTIONS
I. Introduction
The Model 600A Estate Mighty Spreader is designed primarily for the horseman, small farmer,
or homesteader with a need for spreading manure with a small horsepower tractor. It can be
pulled directly into small places, yet has a capacity large enough to minimize the number of
loads. Straw, hay or manure of most consistencies can be spread with ease. Strict adherence to
the maintenance is necessary to insure long life and continued operation.
CAUTION: THE SPREADER SHOULD ONLY BE OPERATED WHEN ALL
SURROUNDINGS ARE CLEAR OF PEOPLE AND BREAKABLE OBJECTS, TO
PREVENT POSSIBLE INJURY OR DAMAGE.
II. ASSEMBLY INSTRUCTIONS
Tools Required:
a. 1/2 inch wrench (opened or box end)
b. 7/16 inch wrench (opened or box end)
c. 3/4 inch wrench (opened end)
d. hammer
e. pliers
f. 3/16” allen wrench
g. 3/32” allen wrench
h. grease gun
i. wood bloc
Assembly Instructions (cont’d)
1. Install hubs onto axles and insert 1/4 x 1-3/4” bolt and lock nut through hub and
axle hole provided.
2. Slide the wheels onto the lug bolts with the valve stem facing outward. Install lug
nuts and tighten securely.
3. Attach the front slant panels to the spreader frame using 4 – 5/16” x 1”
bolt/nut/washer assemblies. Hand tighten only.
4. Assemble the front slant panel boards by bolting the 3 predrilled short boards to
the left and right slant panels, using 6 – 1/4” x 1-1/2”carriage bolts and nuts.
5. Mount both the left and right beater supports on the rear of the spreader using
4 – 5/16” x 1” bolt/nut/washer assemblies.
6. Insert beater stabilizer bar into the square tube on each beater support. Make sure
tube is flush with the bottom of the square tubes. Slight hammer tapping might be
necessary using a wood block between hammer and bar. Insure that the bar is not
cocked to preclude binding of beater during operation.
7. Mount 1 Beater support bearing using 2 – 5/16” x 2-1/4” bolt/nut/washer
assemblies to the left side beater support.
NOTE: bolt must be inserted into the channel on the beater support., so the
threads extend toward the rear of the spreader.
8. Slide short stub of beater into installed beater support bearing. Slide other beater
support bearing onto long shaft side of beater and install on the right side, using
the same process as the left side. Tighten all bolts securely.
9. Install the 3/16” x 5/8” keyway into the beater shaft as shown. Tap keyway until
full seated in slot.
10. Install the beater shaft pulley on to the beater shaft with the set collar facing out.
Make sure that the beater shaft pulley is in line with the lower dive pulley.
Tighten allen screw.
11. Install the v-belt as shown. Make sure the belt is under the belt tightener rod.
12. Connect the spring located at the bottom of the clutch handle, as shown.
13. Loosen bolt on the backside of the clutch handle.
14. Have another person push the belt tightener rod against the v-belt. Pull the clutch
handle forward to apply spring tension. Once the clutch handle is vertical, tighten
the bolt on the back side of the clutch handle to set your tension.
15. Loosen and slide forward the set collar on the clutch hold rod. Move collar 1/2”
away from keyhole slot on the frame. Once set, disengage clutch to check belt
tension. (belt tightener rod should release from v-belt)
16. Install all side rail lumber and side support stakes.
Indice
Manuali Spargitore popolari di altre marche
Fisher
Fisher POLY-CASTER 78601 Manuale utente
TurfEx
TurfEx RS7200 Manuale del proprietario
Ferris
Ferris Pathfinder Series Manuale utente
Fayat Group
Fayat Group DYNAPAC S100 Guida alla risoluzione dei problemi
Art's-Way Manufacturing
Art's-Way Manufacturing X700 Manuale di installazione e funzionamento
EASTMAN
EASTMAN CR 500 Manuale utente
