ETAS ES4602 Manuale utente

ES4602 Breakout Panel

User’s Guide

ES4602 Breakout Panel2

The data in this document may not be altered or amended without special

notification from ETAS GmbH. ETAS GmbH undertakes no further obligation in

relation to this document. The software described in it can only be used if the

customer is in possession of a general license agreement or single license.

Using and copying is only allowed in concurrence with the specifications stip-

ulated in the contract.

Under no circumstances may any part of this document be copied, repro-

duced, transmitted, stored in a retrieval system or translated into another lan-

guage without the express written permission of ETAS GmbH.

The names and designations used in this document are trademarks or brands

belonging to the respective owners.

R1.0.4 EN - 11.2002 TTN F 00K 700 206

Contents 3

Contents

1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2 Connectors CON-L (1) and CON-S (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.3 Connectors CON-L (2) and CON-S (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.4 Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.4.1 Signal Channel Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.4.2 Layout of the Lab Jacks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.5 Safety Measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.6 Signal Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.1 ES4602 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.1.1 Permissible Connector Load . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.1.2 Permissible Backplane Load . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.1.3 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.2 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.3 Connector Pin Allocations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Contents4

5ETAS Contact Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

List of Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Introduction 5

1Introduction

So-called breakout boxes are used to divide the signals between the control

unit and the LabCar allowing the user to simulate a cable break simply by pull-

ing a jumper. The center tabs of the jumpers make it possible to access the

individual control unit signals externally.

The chassis of the ES4602 is a backplane type breakout box. All connectors of

the ES4602 are printed versions. Standard connectors have been selected to

ensure compatibility with other products within the ES46xx series and the cou-

pling boards of the ES4500 component rack.

Using a project-specific front panel, the labels of the individual signal channels

can be customized, and it is possible to mask certain jumpers to avoid faulty or

erroneous connections.

The ES4602 breakout panel is designed as a standard 19” rack-mount type

thus allowing its use both as a stand-alone unit in its own housing and rack-

mounted as part of a LabCar system.

Introduction6

Definitions 7

2 Definitions

ES4500 Component Rack Designates a 19” assembly rack system consist-

ing of the assembly rack, power-supply unit,

and a 20-slot backplane (component rack back-

plane) with 340 loop-through signal lines. It

serves as the mounting rack for related test

plug-in cards.

Coupling board Designates a plug-in board of the ES4500

Component Rack. It allows coupling the com-

ponent rack backplane with external devices

such as control unit, breakout box, or signal

box.

Lab jack system Designates the combination of lab jacks and

the associated jumpers and connectors.

Signal channel Designates a specific signal that is uniquely

identified by its current specification and name

(channel number or label).

Definitions8

Technical Description 9

3 Technical Description

3.1 Overview

The ES4602 breakout panel is mechanically and signal-logically divided into

three areas. The connectors to the control unit ("ECU") are mounted on the

right-hand side (see Figure "Front view of the ES4602 Breakout Panel"

on page 9). The connectors to the ES4500 Component Rack (“LOADBOX”) or

signal box are located on the left.

The jumpers are arranged in the center section. The jumpers are designed

based on the current specification of each signal channel. Some signals in the

range of higher currents are protected specially (see Chapter "Safety Mea-

sures" on page 13).

Fig. 3-1 Front view of the ES4602 Breakout Panel

Although the connectors CON-L (3) and CON-S (3) are included in the back-

plane layout, they are not required at this stage and therefore hidden under a

cover.

Technical Description10

3.2 Connectors CON-L (1) and CON-S (1)

ITT Cannon DLM5-260 connectors are used for signals carrying a maximum

current of 3 A. This connector type is a so-called zero-insertion force connector

with 260 pins. Plugging this connector requires no insertion force for connect-

ing the female and male contacts. A tight connection is ensured by simply

pressing the related contacts against each other. The female and male connec-

tors are locked by turning the lever on the cable plug (see Figure "Fixing the

DLM5-260 Connector (Example)" on page 10).

Fig. 3-2 Fixing the DLM5-260 Connector (Example)

note

The connectors CON-L (load/signal box side connectors) and CON-S (ECU side

connectors) are not protected against erroneous insertion (wrong side, etc.). The

user has to take care to insert the connectors on the correct sides.

DLM5-260

position "open"

DLM5-260

position "closed"

Indice

Altri manuali ETAS Hardware per computer

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente